Home ReviewsRefund
Home/Mitsubishi/Lancer Ralliart/Mitsubishi Lancer Ralliart X рестайлинг (2012-2015)/Repair manual/Hands Free Module - Lancer Evolution/PROBABLE CAUSES
Contents Section: Hands Free Module - Lancer Evolution All sections

PROBABLE CAUSES Mitsubishi Lancer Ralliart X рестайлинг

Hands Free Module - Lancer Evolution ~350 words

PROBABLE CAUSES

  1. The hands free module may be defective.
  2. The multivision display may be defective.
  3. Damaged harness wires and connectors

Required Special Tools

  1. MB991958: Scan Tool (M.U.T.-III Sub Assembly) MB991824: Vehicles Communication Interface (V.C.I.) MB991827: M.U.T.-III USB Cable MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)
  1. STEP 1. Check the combination meter. Check whether the speed meter works normally. (Refer to «SPEEDOMETER CHECK»(/mitsubishi/lancer-ralliart/x-2012-2015/remont/gauges-instrument-panels/#combination-meter-lancer-evolution__speedometer-check) .) Q: Is the check result normal? YES: Go to Step 2. NO: Diagnose the combination meter (Refer to «COMBINATION METER - LANCER EVOLUTION»(/mitsubishi/lancer-ralliart/x-2012-2015/remont/gauges-instrument-panels/#combination-meter-lancer-evolution) ).
  2. STEP 2. Check the multivision operation check if the own vehicle mark is dislocated while driving. Q: Is the check result normal? YES: Go to Step 3. NO: Diagnose the MMCS (Refer to «TROUBLE SYMPTOM CHART»(/mitsubishi/lancer-ralliart/x-2012-2015/remont/communication-devices/#hands-free-module-lancer-evolution__trouble-symptom-chart) .)
  3. STEP 3. Using scan tool MB991958, read the CAN box unit diagnostic trouble code. CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958. Connect scan tool MB991958. Refer to " «HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)»(/mitsubishi/lancer-ralliart/x-2012-2015/remont/communication-devices/#hands-free-module-lancer-evolution__how-to-connect-the-scan-tool) ." Turn the ignition switch to the "ON" position. Check if DTC is set. Turn the ignition switch to the "LOCK" (OFF) position. Q: Is the DTC set? YES: Troubleshoot the MMCS (Refer to «DIAGNOSTIC TROUBLE CODE CHART»(/mitsubishi/lancer-ralliart/x-2012-2015/remont/entertainment-systems/#mitsubishi-multi-communication-system-mmcs-lancer-evolution__diagnostic-trouble-code-chart) ). NO: Go to Step 4.
  4. STEP 4. Check the diagnosis mode Check if the hands free module can be switched to the diagnosis mode. (Refer to «DIAGNOSIS MODE < VEHICLES WITH MMCS >»(/mitsubishi/lancer-ralliart/x-2012-2015/remont/communication-devices/#hands-free-module-lancer-evolution__diagnosis-mode-vehicles-with-mmcs) .) Q: Is the check result normal? YES: Go to Step 5. NO: Perform Inspection Procedure 6: "DIAGNOSIS MODE cannot be made an entry. Mobile Phone item is not displayed on the INFOR screen of MMCS." (Refer to «INSPECTION PROCEDURE 6: DIAGNOSIS MODE CANNOT BE MADE AN ENTRY. MOBILE PHONE ITEM IS NOT DISPLAYED ON THE INFOR SCREEN OF MMCS. < VEHICLES WITH MMCS >»(/mitsubishi/lancer-ralliart/x-2012-2015/remont/communication-devices/#hands-free-module-lancer-evolution__inspection-procedure-6-diagnosis-mode-cannot) .)
  5. STEP 5. Replace the hands free module temporarily, and check the trouble symptom. Q: Is the check result normal? YES: Replace the hands free module. NO: Replace the multivision display.