FASTENER TIGHTENING SPECIFICATIONS
| ITEM | SPECIFICATION |
|---|---|
| Charging system | |
| Evaporative emission purge solenoid bolt | 9.0 +/- 1.0 N. m (80 +/- 9 in-lb) |
| Fuel pressure solenoid bolt | 9.0 +/- 1.0 N. m (80 +/- 9 in-lb) |
| Fuel rail bolt | 11 +/- 1 N. m (98 +/- 8 in-lb) |
| Generator bracket bolt (generator bolt) | 22 +/- 4 N. m (16 +/- 3 ft-lb) |
| Generator bracket bolt (intake manifold bolt) | 20 +/- 2 N. m (16 +/- 3 ft-lb) |
| Generator bracket bolt (water pump bolt) | 22 +/- 4 N. m (15 +/- 1 ft-lb) |
| Generator nut | 44 +/- 10 N. m (33 +/- 7 ft-lb) |
| Generator terminal nut | 14 +/- 3 N. m (124 +/- 26 in-lb) |
| Ground cable bolt | 5.0 +/- 1.0 N. m (44 +/- 9 in-lb) |
| Oil level gauge guide bolt | 13 +/- 1 N. m (115 +/- 9 in-lb) |
| Water pump pulley bolt | 8.8 +/- 1.0 N. m (78 +/- 9 in-lb) |
| Starting system | |
| Starter bolt | 30 +/- 3 N. m (23 +/- 2 ft-lb) |
| Starter cover bolt | 4.9 +/- 1.0 N. m (44 +/- 8 in-lb) |
| Starter cover nut | 4.9 +/- 1.0 N. m (44 +/- 8 in-lb) |
| Starter terminal nut | 13 +/- 2 N. m (111 +/- 22 in-lb) |
| Ignition system | |
| Camshaft position sensor bolt (exhaust side) | 10.5 +/- 0.5 N. m (93 +/- 4 in-lb) |
| Camshaft position sensor bolt (inlet side) | 10.5 +/- 0.5 N. m (93 +/- 4 in-lb) |
| Crankshaft position sensor bolt | 8.8 +/- 1.0 N. m (78 +/- 9 in-lb) |
| Ignition coil bolt | 10 +/- 2 N. m (89 +/- 17 in-lb) |
| Knock sensor | 23 +/- 2 N. m (17 +/- 1 ft-lb) |
| Power steering oil pressure hose bolt | 12 +/- 2 N. m (102 +/- 22 in-lb) |
| Power steering oil pump bracket bolt (cylinder block side) | 49 +/- 9 N. m (36 +/- 7 ft-lb) |
| Power steering oil pump bracket bolt (power steering oil pump side) M8 | 22 +/- 4 N. m (16 +/- 3 ft-lb) |
| M10 | 40 +/- 5 N. m (30 +/- 3 ft-lb) |
| Power steering oil pump heat protector bolt | 22 +/- 4 N. m (16 +/- 3 ft-lb) |
| Power steering oil reservoir bolt | 12 +/- 2 N. m (102 +/- 22 in-lb) |
| Spark plug | 25 +/- 4 N. m (18 +/- 3 ft-lb) |
FASTENER TIGHTENING SPECIFICATIONS
GENERAL SPECIFICATIONS
| ITEMS | SPECIFICATIONS |
|---|---|
| Generator | |
| Type | Positive battery positive voltage sensing |
| Identification number | A3TB1791 |
| Part No. | MD366831 |
| Rated output V/A | 12/90 |
| Voltage regulator | Electronic built-in type |
| Starter motor | |
| Type | Reduction drive with planetary gear |
| Identification number | M0T31771 |
| Part No. | 1810A025 |
| Rated output kW/V | 1.2/12 |
| Number of pinion teeth | 8 |
| Ignition coil | |
| Type | Molded 2-coil |
| Spark plugs | |
| NGK | ILFR7H |
GENERAL SPECIFICATIONS
SERVICE SPECIFICATIONS
| ITEMS | STANDARD VALUE | LIMIT | |
|---|---|---|---|
| Generator | |||
| Regulated voltage (Ambient temperature at voltage regulator) | 20 °C (-4° F) | 14.2 - 15.4 | |
| 20°C (68°F) | 13.9 - 14.9 | ||
| 60°C (140°F) | 13.4 - 14.5 | ||
| 80°C (176°F) | 13.1 - 14.5 | ||
| Generator output line voltage drop (at 30A) V | Maximum 0.3 | ||
| Output current | 70% of normal output current | ||
| Field coil resistance ohms | Approximately 2 - 5 | ||
| Brush protrusion length mm (in) | Minimum 2 (0.08) | ||
| Starter motor | |||
| Free running characteristics | Terminal voltage V | 11 | |
| Current A | 95 | ||
| Speed r/min | 2,500 or more | ||
| Pinion gap mm (in) | 0.5 - 2.0 (0.02 - 0.07) | ||
| Commutator run-out mm (in) | 0.05 (0.002) | Minimum 0.1 (0.004) | |
| Commutator diameter mm (in) | 29.4 (1.16) | Minimum 28.8 (1.13) | |
| Undercut depth mm (in) | 0.5 (0.02) | Minimum 0.2 (0.008) | |
| Ignition parts | |||
| Ignition secondary coil resistance at 20° C (68° F) kohms. | 8.5-11.5 | ||
| Spark plug gap mm (in) | 0.5 - 0.6 (0.020 - 0.024) | 0.75 (0.0295) | |
| Spark plug cable resistance kohms | Maximum 19 | ||
SERVICE SPECIFICATIONS