FASTENER TIGHTENING SPECIFICATIONS
| ITEM | SPECIFICATION |
|---|---|
| Front deck stay mounting nut | 5.0 +/- 1. 0 N.m (44 +/- 9 in-lb) |
| Front deck crossmember mounting bolt (installation from the side of left position) | 22 +/- 4 N.m (16 +/- 3 ft-lb) |
| Front deck crossmember mounting bolt (installation from the front side of left position) | 12 +/- 2 N.m (102 +/- 22 in-lb) |
| Front deck crossmember mounting bolt (installation from the left side of center position) | 22 +/- 4 N.m (16 +/- 3 ft-lb) |
| Front deck crossmember mounting bolt (installation from the right side of center position) | 12 +/- 2 N.m (102 +/- 22 in-lb) |
| Front deck crossmember mounting bolt (installation of right position) | 22 +/- 4 N.m (16 +/- 3 ft-lb) |
| Liquid pipe mounting nut (heater unit side) | 4.9 +/- 0.9 N.m (43 +/- 8 in-lb) |
| Liquid pipe mounting bolt (condenser side) | 4.9 +/- 0.9 N.m (43 +/- 8 in-lb) |
| Flexible suction hose mounting nut (compressor side) | 25 +/- 4 N.m (18 +/- 3 ft-lb) |
| Suction pipe mounting nut (heater unit side) | 12 +/- 2 N.m (107 +/- 17 in-lb) |
| Flexible discharge hose mounting bolt (compressor side) | 25 +/- 4 N.m (18 +/- 3 ft-lb) |
| Flexible discharge hose mounting nut (condenser side) | 12 +/- 2 N.m (107 +/- 17 in-lb) |
FASTENER TIGHTENING SPECIFICATIONS
GENERAL SPECIFICATIONS
| ITEM | MANUAL AIR CONDITIONING | |
|---|---|---|
| Heater control | Dial type | |
| A/C switch | Push-button type | |
| Compressor | MSC105CA (Scroll type) | |
| Refrigerant | Type | R134a (HFC-134a) |
| Amount g (oz) | 530-570 (18.7-20.1) | |
GENERAL SPECIFICATIONS
SERVICE SPECIFICATIONS
| ITEM | STANDARD VALUE | |
|---|---|---|
| Idle speed r/min | 2.4L ENGINE | 700 +/- 50 |
| Idle speed r/min | 3.8L ENGINE | 680 +/- 50 |
| Idle-up speed r/min | 2.4L ENGINE | 700 +/- 50 |
| Idle-up speed r/min | 3.8L ENGINE | 680 +/- 50 |
| Air mix damper potentiometer resistance kohms | 1.7-5.0 | |
| Air outlet changeover damper potentiometer resistance kohms | 0.8-4.8 | |
| Resistor resistance kohms | (LO) | 2.54 |
| (ML) | 1. 24 | |
| (MH) | 0.6 | |
| Air gap (A/C compressor clutch) mm (in) | 0.3-0.5 (0.012-0.020) | |
| Cooling temperature switch | Less than 2 ohms | Slightly below 155°C (311°F) |
| No continuity | 155°C (311°F) or more [up to 125°C (257°F) when temperature drops] | |
SERVICE SPECIFICATIONS
See also:
• DIAGNOSTIC TROUBLE CODE
• DIAGNOSTIC TROUBLE CODE