General Description
FAM is a component of BCM that consists of DDM, ADM, FAM, RAM, IMS and cluster module. Each component of BCM controls relative unit and share information by CAN communication line. FAM is abbreviation of Front Area Module. it is located in the engine room and controls wiper and all kinds of lamp (Head lamp, tail lamp, stop lamp, turn signal lamp etc.), Beside that, FAM performs diagnosis of system.
DTC Description
The ECM sets DTC B1624 if there's any fault in writing/reading FAM EEPROM data procedure.
FAM is a component of BCM that consists of DDM, ADM, FAM, RAM, IMS and cluster module. Each component of BCM controls relative unit and share information by CAN communication line. FAM is abbreviation of Front Area Module. it is located in the engine room and controls wiper and all kinds of lamp (Head lamp, tail lamp, stop lamp, turn signal lamp etc.), Beside that, FAM performs diagnosis of system.
The ECM sets DTC B1627 if there's any fault in writing/reading FAM EEPROM data procedure.
When signal error occurs in BCM module, Rescue mode is activated for the safety or driver. System operating state is divided into Normal mode, Safe mode and Rescue mode. Normal mode indicates every modules are in good condition, Safe mode is the transitional mode between Normal and Rescue mode which prevents system jamming arised by intermittent abnormal signal. If error signal is inputted to BCM continuously in Safe mode, Rescue mode - the next mode - is activated. Rescue mode is classified into software Rescue mode which is applied when important CAN signal or hardware input is unavailable and hardware Rescue mode which is applied when hardware Watchdog toggle does not turn on. When system comes to be in normal operating condition, Rescue mode is deactivated then it returns to Normal mode.
The ECM sets DTC B1646 if Rescue mode is activated at FAM.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received wind shield defogger switch signal from IPM through CAN line, FAM controls wind shield defogger.
The ECM sets DTC B2119 if open/short in wind shield defogger circuit or relay failure is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. the power of stop lamp is supplied from the power line through FAM-->stop lamp-->RAM-->lamp in sequence. Controlling stop lamp is performed at FAM and RAM. FAM transfers power from "HOT AT ALL TIMES power circuit" to stop lamp switch and via RAM, this power is supplied to stop lamp. Furthermore, RAM senses stop lamp circuit error as well.
The ECM sets DTC B2521 if open in stop lamp circuit is detected between "HOT AT ALL TIMES power circuit" and FAM.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2535 if short to ground in Right turn signal lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2537 if open in Right turn signal lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2539 if short to ground in Left turn signal lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2541 if open in Left turn signal lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2543 if short to ground in Right head lamp high circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2545 if open in Right head lamp high circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2547 if short to ground in Left head lamp high circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2549 if open in Left head lamp high circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2551 if short to ground in Right head lamp low circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2553 if open in Right head lamp low circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2555 if short to ground in Left head lamp low circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2557 if open in Left head lamp low circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2559 if short to ground in Right fog lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2561 if open in Right fog lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2563 if short to ground in Left fog lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2565 if open in Left fog lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2571 if short to ground in Right parking lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2573 if open in Right parking lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2575 if short to ground in Left parking lamp circuit is detected.
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is connected to one another through CAN communication line for efficient communication. Those modules control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other modules. Front Area Module (FAM) set up at engine room controls various lamps (fog lamp, head lamp, stop lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch head lamp signal from IPM through CAN line, FAM controls head lamp with integrated IPS. IPS is a semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing circuit error, circuit protection.
The ECM sets DTC B2577 if open in Left parking lamp circuit is detected.