Power Window Control System (Convertible): Overview Infiniti Q60 I

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL: Description

Initial setting is necessary when battery terminal is removed.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT: Description

Initial setting is necessary when replacing power window main switch.

POWER WINDOW OPERATION

1. Power window main switch can open/close all windows.
2. Power window sub-switch can open/close the passenger side windows.
3. Retained power operation can operate power window switch and power window sub-switch for 45 seconds after ignition switch is turned OFF.
4. Power window lock function prohibits operation other than power window main switch when lock switch is pressed.
5. Anti-pinch function lowers door glass a specific amount during power window AUTO UP operation when resistance is detected because of a trapped foreign object.
6. Power window serial link transmits and receives signal between retractable hard top control unit and power window main switch or power window sub-switch.
7. Power window system operation links with retractable hard top system to " «RETRACTABLE HARD TOP SYSTEM: SYSTEM DESCRIPTION»(/infiniti/q60/i-2013-2016/remont/sun-rooft-topconvertible-top/#roof-convertible) ".

POWER WINDOW AUTO-OPERATION

1. Driver and passenger power window motors operate AUTO UP/DOWN when power window main switch or power window sub-switch is operated in AUTO.
2. Power window main switch and power window sub-switch read the changes of encoder signal and stop AUTO operation when door glass is fully open or closed. (Anti-pinch function does not operate just before door glass is fully closed and before it is fully closed.)
3. Even if encoder is malfunctioning, power window motors are operative (except during AUTO operation).
4. For rear power window motor, only AUTO DOWN operation is operative.

POWER WINDOW SIMULTANEOUS OPERATION

All door glass moves upward (downward) when driver side front switch and passenger side front switch of power window main switch are simultaneously pulled (pressed) in AUTO position.

Note. This function is adopted in consideration of convenience after all door glass is fully closed (open) when retractable hard top is operated.

RETAINED POWER OPERATION

1. During 45 seconds after ignition switch is turned OFF, BCM controls timer and enables open and close operation of driver door glass, passenger door glass, and rear quarter glass.

Note. Retained power operation is not operative when system initialization is not complete.

Retained power function cancel conditions

When BCM detects the following signal it cancels.

1. Door CLOSE (door switch OFF)-->OPEN (door switch ON).
2. Ignition switch is ON.
3. Timer time passes. (45 seconds)

OPERATION CONDITION

1. When all door glass AUTO-UP operation is performed (anti-pinch function does not operate just before the door glass closes and is fully closed)

Note. Depending on environment and driving conditions, if a similar impact or load is applied to the door glass, it may lower.

KEY CYLINDER SWITCH OPERATION

Hold the door key cylinder the LOCK or UNLOCK direction for 1 second or more to OPEN or CLOSE all power windows when ignition switch is OFF. In addition, it stops when key position is moved to NEUTRAL when operating.

1. Ignition switch OFF.
2. Hold door key cylinder LOCK position for 1 second or more to perform CLOSE operation of the door glass.
3. Hold door key cylinder UNLOCK position for 1 second or more to perform OPEN operation of the door glass.

KEYLESS POWER WINDOW DOWN OPERATION

All power windows open when the unlock button on Intelligent Key is activated and kept pressed for more than 3 seconds with the ignition switch OFF. The windows keep opening if the unlock button is continuously pressed.

The power window opening stops when the following operations are performed.

1. When the ignition switch is turned ON while the power window opening is operated.
2. When the unlock button is released.

While retained power operation keyless power window down function cannot be operated.

Keyless power window down operation mode can be changed by "PW DOWN SET" mode in "WORK SUPPORT". Refer to " INTELLIGENT KEY: CONSULT FUNCTION (BCM - INTELLIGENT KEY) ".

Note. Use CONSULT to change settings.

MODE 1 (3 sec)/MODE 2 (OFF)/MODE 3 (5 sec)

Component Description

DRIVER SIDE: Description

Door glass moves UP/DOWN by receiving the signal from power window main switch.

PASSENGER SIDE: Description

Door glass moves UP/DOWN by receiving the signal power window main switch or power window sub-switch.

REAR LH: Description

Door glass moves UP/DOWN by receiving the signal from power window main switch.

REAR RH: Description

Door glass moves UP/DOWN by receiving the signal power window main switch or power window sub-switch.

Detects door open/closed condition.

Detects door open/closed condition.

Detects condition of the driver side power window motor operation and transmits to power window main switch as the pulse signal.

Detects condition of the passenger side power window motor operation and transmits to power window sub-switch as the pulse signal.

Description

Power window main switch detects condition of the door key cylinder switch and transmits to BCM as the LOCK or UNLOCK signals.

All power windows do not operate via power window main switch and power window sub-switch.

Driver side power window does not operate using power window main switch.

Passenger side power window operates using power window main switch and power window sub-switch.

Anti-pinch function does not operate when power window up operated.

Retained power function does not operate after ignition switch turns OFF.

Power window does not operate when locking or unlocking a door using door key cylinder.

Power window down does not operate when pressing unlock button on Intelligent Key.

See also:
• RETRACTABLE HARD TOP SYSTEM: SYSTEM DESCRIPTION