Home ReviewsRefund
Home/GMC/Sierra/GMC Sierra III (2013-2015)/Repair manual/Communication Devices/Programming and Setup - All Systems: Removal & Installation
Contents Wiring diagrams Section: Communication Devices All sections

Programming and Setup - All Systems: Removal & Installation GMC Sierra III

Communication Devices ~2655 words

Replace and Program Active Safety Control Module or Reprogram Active Safety Control Module

To program a replacement or an existing active safety control module, perform the following procedure

  1. Access the Service Programming System (SPS) and follow the on-screen instructions.
  2. On the SPS Supported Controllers screen, select Active Safety Control Module - Programming and follow the on-screen instructions.
  3. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

Replace and Program Control Module or Reprogram Control Module

To program a replacement or an existing control module, perform the following procedure

  1. Install the EL-49642 SPS Programming Support Tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select T3 Audio Amplifier - Programming and follow the on-screen instructions.
  4. At the end of programming, choose the "Clear DTCs" function on the SPS screen.

Replace and Program Control Module

To program a replacement Body Control Module (BCM), perform the following procedure

  1. Install EL-49642 SPS programming support tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select BCM Body Control Module - Configuration and follow the on-screen instructions (if applicable).
  4. On the SPS Supported Controllers screen, select BCM Body Control Module - Programming and follow the on-screen instructions.
  5. Perform the following for the appropriate ignition type prior to proceeding with the next step: Key Ignition System: Key in the ignition and any additional keys must be away from the vehicle at least 3 meters. Push Button Start System: Keyless entry transmitter must be in the programming pocket. Refer to the owner manual for the exact pocket location. All additional transmitters must be away from the vehicle at least 3 meters.
  6. On the SPS Supported Controllers screen, select IMMO Immobilizer Learn - Setup. On the next screen, select Body Control Module IMMO Learn with Existing Transponder or Remote Key and follow the on-screen instructions. When Immobilizer Learn is complete, press the Unlock button on the keyless entry transmitter to allow the keyless entry transmitter to exit the Immobilizer Learn mode.
  7. On the SPS Supported Controllers screen, select BCM Body Control Module - Setup and follow the on-screen instructions.
  8. Check the driver information center display for additional messages regarding further calibration instructions. If there are no additional driver information center instructions present, programming is complete.
  9. At the end of programming, choose the "Clear DTCs" function on the SPS screen.
  10. If ABS, Traction Control and/or Stabilitrak indicators are ON and DTC C0161 is set in the electronic brake control module after performing BCM programming and setup, do the following: Disconnect the scan tool from the data link connector. Ignition OFF, all access doors closed, all vehicle systems OFF and all keys at least 3 meters away from the vehicle. It may take up to 2 minutes to power down. Ignition ON, verify DTC C0161 is in history. If not, repeat the above step to make sure the vehicle is in sleep mode. Use the scan tool to clear the DTCs.

Communication Interface Module Replacement

Note. It is critical to use the service replacement Communication Interface Module only in the vehicle for which it was ordered. Failure to perform the following procedures will result in a red LED, DTC(s) being set and limited or incomplete OnStar® services. An OnStar® button press to the OnStar® call center is not required to complete the procedure. It may take up to 24 hours for OnStar® service to become fully activated after performing the procedures. Perform the following procedure only once. Repeat attempts of the procedure may result in a delay of the activation process. To fully activate an OnStar® module, both the setup and activation request procedures must be completed on all vehicles with and without an active OnStar® subscription to insure the unit has been setup properly for the vehicle it has been installed into and also to update the OnStar® with the correct unit information. To initialize the Turn-by-Turn feature, the vehicle must first be driven In open sky condition at speeds greater than 10 mph (16 kph) or more for a minimum of 5 miles (8 km) and perform at least 2 left and 2 right 90 degree turns coming to complete stops prior to each turn. On vehicles up fitted with TTY capabilities, it is necessary to perform a power cycle of the OnStar® Interface Module (OTIM) and toggle the TTY mode after completing the Communication Interface Module installation and setup procedures.

  1. Install EL-49642 SPS programming support tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select ONSU Onstar® Module Setup and Service Activation and follow the on-screen instructions.
  4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
  5. The default language for the new Communication Interface Module is English. To change to an alternate language, access the scan tool.
  6. Inform the customer that it may take up to 24 hours for the OnStar® service to become fully activated.

Transmission Control Module (TCM) Replacement

If the TCM is replaced, the following procedures must be performed

  1. TCM Reprogramming
  2. The Reset Transmission Adapts - Refer to «Reset Transmission Adapts»(ref-651072-S41378778212014081900000)

Setup for Component Replacement

The replacement of some components will require a setup procedure for complete repair.

If any of the following components are replaced, the Reset Transmission Adapts procedure must be performed

  1. Transmission replacement
  2. Any internal transmission repair
  3. Any speed sensor

Refer to Reset Transmission Adapts .

Replace and Program ECU or Reprogram ECU

To program a replacement or an existing ECU, perform the following procedure

  1. Install EL-49642 SPS Programming Support Tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select TCM - Programming and follow the on-screen instructions.
  4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
  5. Perform the following all transmission related repairs.

The replacement of some components will require a setup procedure for complete repair.

If any of the following components are replaced, the procedure must be performed

  1. Transmission replacement
  2. Any internal transmission repair
  3. Any speed sensor

Refer to .

To program a replacement or an existing control module, perform the following procedure

  1. Install EL-49642 SPS Programming Support Tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select K17 Electronic Brake Control Module - Programming and follow the on-screen instructions.
  4. On the SPS Supported Controllers screen, select K17 Electronic Brake Control Module - Setup and Configuration and follow the on-screen instructions.
  5. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

If the engine control module (ECM) is replaced, the following procedures must be performed

  1. Connect a scan tool to the vehicle and access SPS. Refer to «Service Programming System (SPS)»(ref-651024-S41378629092014081900000) .
  2. Before removing the old control module, perform the SPS function Prepare Control Module for Removal, if available. NOTE: The Prepare Control Module for Removal function can only be performed when communication with the old control module is still possible.
  3. Replace the ECM.
  4. Perform the SPS function Engine Control Module - Programming and follow the on-screen instructions.
  5. Clear the DTCs after completing the Programming procedure.
  6. Perform the SPS function Immobilizer Learn and follow the on-screen instructions. Refer to «Immobilizer System Component Programming»(ref-651020-S23187677182014081900000) .
  7. Perform the SPS function Engine Control Module - Configuration & Setup and follow the on-screen instructions.
  8. Clear DTCs after completing the Configuration & Setup procedure.

Replace and Program the Front and Rear Parking Assist Control Module

If the front and rear parking assist control module needs to be replaced, the following procedures must be performed

  1. Connect a scan tool to the vehicle and access SPS. Refer to «Service Programming System (SPS)»(ref-651024-S41378629092014081900000)
  2. Perform the SPS function Front and Rear Parking Assist Control Module Programming and follow the on-screen instructions.
  3. Perform the SPS function Front and Rear Parking Assist Control Module Configuration and follow the on-screen instructions.
  4. Clear DTCs after completing the programming procedure.

Front View Camera Module Replacement

If the Front View Camera Module needs to be replaced, the following procedures must be performed

  1. Connect a scan tool to the vehicle and access Service Programming System (SPS).
  2. Perform the SPS function Front View Camera Module - Programming and follow the on-screen instructions.
  3. Perform the SPS function Front View Camera Module - Configuration & Setup and follow the on-screen instructions.
  4. Clear DTCs after completing the programming procedure.

This ECU does not require SPS programming but does require the following setup procedures after a new ECU is installed

The customer must learn the device they wish to control. This must be done at the device (garage door opener, electric gate, etc.) and cannot be performed at a dealership. Refer to the vehicle owner's manual for programming instructions.

To program a replacement control module, perform the following procedure

  1. Install the EL-49642 SPS Programming Support Tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select K74 Human Machine Interface Control Module - Programming and follow the on-screen instructions.
  4. Connect a USB drive to the computer.
  5. Access the Service Programming System (SPS) and follow the on-screen instructions.
  6. On the SPS Supported Controllers screen, select K74 Human Machine Interface Control Module - USB File Transfer. NOTE: All existing files on the USB drive will be erased when the new files are copied.
  7. Upon completion of the file transfer, remove the USB drive from the computer.
  8. Ignition ON, infotainment system ON.
  9. Connect the USB drive to the USB port in the vehicle.
  10. The infotainment system will recognize that update files are available. Follow the infotainment display on-screen instructions and select Update when prompted. Programming will take several minutes.
  11. Upon completion of programming, remove the USB drive. Follow the infotainment display on-screen instructions.
  12. At the end of programming, choose the "Clear DTCs" function on the SPS screen.

HVAC Control Module Replacement

If the HVAC control module needs to be replaced, the following procedures must be performed

  1. Connect a scan tool to the vehicle and access SPS. Refer to «Service Programming System (SPS)»(ref-651024-S41378629092014081900000) .
  2. Perform the SPS function Remote Heater and Air Conditioning Control Module - Programming and follow the on-screen instructions.
  3. Perform the SPS function Remote Heater and Air Conditioning Control Module - Configuration & Setup and follow the on-screen instructions.
  4. Clear DTCs after completing the programming procedure.

If an actuator is replaced, the following procedure must be performed

Recalibrating actuators for the HVAC system. Refer to Actuator Recalibration .

This ECU does not require SPS programming or any setup procedures.

Replace and Program ECU

To program a replacement or an existing ECU, perform the following procedure

  1. Install EL-49642 SPS programming support tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select Instrument Cluster - USB File Transfer and follow the on-screen instructions.
  4. On the SPS Supported Controllers screen, select Instrument Cluster - Programming and follow the on-screen instructions.
  5. On the SPS Supported Controllers screen, select Instrument Cluster - Setup and Configuration and follow the on-screen instructions.
  6. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

Replace and Program Radar Sensor Module - Long Range or Reprogram Radar Sensor Module - Long Range

To program a replacement or an existing Long Range Radar Sensor Module, perform the following procedure

  1. Access the Service Programming System (SPS) and follow the on-screen instructions.
  2. On the SPS Supported Controllers screen, select B233B Radar Sensor Module - Long Range - Programming and follow the on-screen instructions.
  3. Ignition OFF.
  4. Following programming, the module alignment must be calibrated. Refer to «Radar Sensor Module - Long Range Calibration»(ref-651049-S22536216432014081900000) .

If the front and rear parking assist control module needs to be replaced, the following procedures must be performed

  1. Connect a scan tool to the vehicle and access SPS. Refer to «Service Programming System (SPS)»(ref-651024-S41378629092014081900000)
  2. Perform the SPS function Front and Rear Parking Assist Control Module Programming and follow the on-screen instructions.
  3. Perform the SPS function Front and Rear Parking Assist Control Module Configuration and follow the on-screen instructions.
  4. Clear DTCs after completing the programming procedure.

To program a replacement or an existing control module, perform the following procedure

Without Rear Seat Video Entertainment System

This control module does not require SPS programming or any setup procedures.

With Rear Seat Video Entertainment System

  1. Install the EL-49642 SPS Programming Support Tool.
  2. Connect a USB drive to the computer.
  3. Access the Service Programming System (SPS) and follow the on-screen instructions.
  4. On the SPS Supported Controllers screen, select Media Disc Player - USB File Transfer and follow the on-screen instructions.
  5. Upon completion of the file transfer, remove the USB drive from the computer.
  6. Ignition ON, infotainment system ON.
  7. Connect the USB drive to the USB port in the vehicle.
  8. The infotainment system will recognize that update files are available. Follow the infotainment display on-screen instructions and select Update when prompted. Programming will take several minutes.
  9. Upon completion of programming, remove the USB drive. Follow the infotainment display on-screen instructions.
  10. On the SPS Supported Controllers screen, select Media Disc Player - Programming and follow the on-screen instructions.
  11. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

To program a replacement power steering control module, perform the following procedure

  1. Install EL-49642 SPS programming support tool.
  2. Ignition ON.
  3. Access the Service Programming System (SPS) and follow the on-screen instructions.
  4. On the SPS Supported Controllers screen, select Power Steering Control Module - Programming and follow the on-screen instructions.
  5. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
  6. On the SPS Supported Controllers screen, select Power Steering Control Module - Setup and follow the on-screen instructions.
  7. With a scan tool, Clear All DTCs.

To program a replacement or an existing control module, perform the following procedure

  1. Access the Service Programming System (SPS) and follow the on-screen instructions.
  2. On the SPS Supported Controllers screen, select B233 Radar Sensor Module - Short Range - Programming and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select B233 Radar Sensor Module - Short Range - Setup and follow the on-screen instructions.
  4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
  5. Following programming, the module ID must be programmed. With a scan tool, perform the Radar Sensor Module - Short Range learn procedure.

This ECU does not require SPS programming or any setup procedures.

To program a replacement or an existing control module, perform the following procedure

  1. Install EL-49642 SPS Programming Support Tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select A11 Radio - Programming and follow the on-screen instructions.
  4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

This ECU does not require SPS programming or any setup procedures.

To program a replacement or an existing ECU, perform the following procedure

  1. Access the Service Programming System (SPS) and follow the on-screen instructions.
  2. On the SPS Supported Controllers screen, select B218 Side Object Sensor Module - Programming and follow the on-screen instructions.
  3. At the end of programming, choose the "Clear DTCs" function on the SPS screen.

Transfer Case Shift Control Module Replacement

If the transfer case shift control module is replaced, the transfer case shift control module reprogramming procedure and the Transfer Case High/Low Clutch Reset procedures must be performed. Refer to Service Programming System (SPS)

If the transfer case shift control module is replaced, the transfer case shift control module reprogramming procedure and the Transfer Case High/Low Clutch Reset procedures must be performed. Refer to Service Programming System (SPS) .

If the TCM is replaced, TCM Reprogramming must be performed. Refer to Service Programming System (SPS) .

If the TCM is replaced, TCM Reprogramming must be performed. Refer to Service Programming System (SPS) .

More articles — Programming and Setup - All Systems