Programming and Setup - All Systems: Removal & Installation GMC Savana H1500

EBCM Replacement

If the electronic brake control module (EBCM) is replaced, the following procedures must be performed

1. EBCM programming: Refer to «Service Programming System (SPS)»(ref-302118-S04909991502008102100000) .
2. With a scan tool, perform the yaw rate sensor recalibration and follow the on-screen instructions.

ECM Replacement

If the engine control module (ECM) is replaced, the following procedures must be performed

1. Capture the Option data.
2. Enable ECM Reprogramming-Refer to «Service Programming System (SPS)»(ref-302118-S04909991502008102100000) .
3. Restore the Option data in the new ECM.
4. Start and idle vehicle.
5. Using the scan tool, perform the Turbocharger Learn Procedure. Refer to «Turbocharger Learn»(ref-302156-S26001170062008102100000) .
6. Perform a DPF Regeneration Enable. Refer to «Exhaust Particulate Filter Cleaning (LMM DPF Service Regeneration)»(ref-302161-S01920738422008102100000) or «Exhaust Particulate Filter Cleaning (LMM DPF Regeneration Enable)»(ref-302161-S08277797462008102100000) .
7. If necessary, perform the following: Theft Deterrent-Refer to «Theft Deterrent Control Module Programming and Setup»(ref-302118-S08453553172008102100000) . The Fuel Injector Flow Rate Programming-Refer to «Fuel Injector Flow Rate Programming»(ref-302156-S20932469062008102100000) . Engine Oil Life Remaining-Use scan tool to reset Engine Oil Life. Fuel Filter Life-Use scan tool to reset Fuel Filter Life.

Setup for Component Replacement

The replacement of some components will require a setup procedure for complete repair.

If any of the following components are replaced, a Turbocharger Learn Procedure must be performed.

1. Turbocharger
2. Turbocharger Vane Position Sensor
3. Turbocharger Vane Position Control Solenoid Valve

If the engine control module (ECM) is replaced, the following procedures must be performed

1. The ECM Reprogramming-Refer to «Service Programming System (SPS)»(ref-302118-S04909991502008102100000) .
2. The CKP Variation Learn-Refer to «Crankshaft Position System Variation Learn»(ref-302155-S14465333272008102100000) .
3. The Theft Deterrent Programming-Refer to «Theft Deterrent Control Module Programming and Setup»(ref-302118-S08453553172008102100000) .
4. The Fuel Composition Diagnostic-Refer to «Alcohol/Contaminants-In-Fuel Diagnosis (With Special Tool)»(ref-302164-S30754127022008102100000) .
5. Engine Oil Life Remaining-When available, use a scan tool to reset the Engine Oil Life Remaining back to the original percentage recorded before the module was replaced.
6. Transmission Fluid Life Remaining-When available, use a scan tool to reset the Transmission Fluid Life Remaining back to the original percentage recorded before the module was replaced.

The replacement of some components will require a setup procedure for complete repair.

If any of the following components are replaced, a CKP Variation Learn Procedure must be performed. Refer to Crankshaft Position System Variation Learn .

1. Engine replacement
2. Any engine repair that disturbs the crankshaft position (CKP) sensor or its relationship with the crankshaft reluctor wheel
3. CKP sensor

GPCM Replacement

If the glow plug controller (GPCM) is replaced, the following procedures must be performed.

Fuel Injector Flow Rate Programming for fuel injector flow rate programming

The replacement of some components will require a setup procedure for complete repair.

If any of the following components are replaced, the Fuel Injector Flow Rate Programming must be performed. Refer to Fuel Injector Flow Rate Programming .

1. Fuel injector
2. Engine control module (ECM)
3. GPCM

Radio Replacement

If the radio is replaced, the new radio must have the setup procedure performed. Refer to Radio Setup .

Remote Control Door Lock Receiver Replacement - Copy and Paste TPM Information

This procedure will learn the TPM information to the new RCDLR using the Copy and Paste function on the scan tool. This procedure will extract the TPM Tire Type information as well as the sensor data from the existing RCDLR prior to its replacement and store this information in the scan tool. After RCDLR replacement and SPS programming, the tire type and sensor data stored in the scan tool is written to the new RCDLR, negating the need to perform the tire type setup and sensor learn procedure.

This procedure should be considered as the first programming choice when replacing an RCDLR. The Copy and Paste procedure eliminates the possibility of incorrectly inputting the tire type or learning stray TPM sensors.

1. Using a scan tool, navigate to the Copy and Paste TPM Information procedure and copy the existing TPM information from the RCDLR using the outline below. Follow the on-screen instructions after selecting Step 1: Vehicle Control Systems Module Setup Remote Control Door Lock Receiver Copy and Paste TPM Information Step 1
2. At this point, install the new RCDLR.
3. Program the RCDLR - Refer to «Service Programming System (SPS)»(ref-302118-S04909991502008102100000) .
4. Using a scan tool, navigate to the Copy and Paste TPM Information procedure to paste the stored TPM information using the outline below. Follow the on-screen instructions after selecting Step 2: Vehicle Control Systems Module Setup Remote Control Door Lock Receiver Copy and Paste TPM Information Step 2
5. Program the keyless entry transmitters - Refer to «Transmitter Programming»(ref-302136-S31087148732008102100000) .

Remote Control Door Lock Receiver Replacement - TPM Sensor Learn

This procedure will learn TPM information to the new RCDLR by manually inputting the tire type using the scan tool and performing the TPM sensor learn. This procedure should be performed if the above Copy and Paste procedure can not be completed. An example of this would be an RCDLR that is unable to communicate with the scan tool and is required to be replaced.

1. RCDLR Programming-Refer to «Service Programming System (SPS)»(ref-302118-S04909991502008102100000) .
2. Keyless Entry Transmitter Programming-Refer to «Transmitter Programming»(ref-302136-S31087148732008102100000) .
3. Tire Type Setup: Install a scan tool. Select Remote Control Door Lock Receiver under Module Setup in the Vehicle Control System menu. Select Tire Type/Pressure Selection. Follow the on-sceen instructions.
4. Tire Pressure Monitoring Sensor Learn-Refer to «Tire Pressure Sensor Learn»(ref-302162-S25881113182008102100000) .