Memory Seat Operation
The driver seat control switch provides a ground signal to the DSM only when activated. This ground signal causes the DSM to power the appropriate motor until the input is removed. The motor circuits are normally grounded through the DSM . The DSM internally switches the appropriate circuit from ground to voltage to operate the motors.
As the seat is adjusted, the DSM monitors the motor position sensors to record the current seat position. The DSM removes voltage from the motor upon termination of the seat control switch input or if the DSM does not detect movement from the motor while monitoring the position sensor during a memory recall operation.
Normal Operation and Fault Conditions
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
| DTC | Description | Fault Trigger Conditions |
|---|---|---|
| B1060:11 | Seat Headrest Motor Output (Seat Lumbar Motor Output): Circuit Short To Ground | This DTC sets when the DSM detects the deflate or inflate relay (integral to the DSM ) is stuck or a short to ground is present in the output circuit. |
| B1060:15 | Seat Headrest Motor Output (Seat Lumbar Motor Output): Circuit Short To Battery or Open | This DTC sets when the DSM detects the deflate or inflate relay (integral to the DSM ) is stuck or a short to voltage is present in the output circuit. |
| B106D:24 | Headrest Up Switch (Lumbar Forward Switch): Signal Stuck High | This DTC sets when the DSM detects the lumbar control switch is stuck in the rearward (inflate) position or a short to ground is present on the inflate input circuit for greater than 30 seconds. |
| B106E:24 | Headrest Down Switch (Lumbar Rearward Switch): Signal Stuck High | This DTC sets when the DSM detects the lumbar control switch is stuck in the forward (deflate) position or a short to ground is present on the deflate input circuit for greater than 30 seconds. |
DTC FAULT TRIGGER CONDITIONS
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
| DTC | Description | Fault Trigger Conditions |
|---|---|---|
| B1B86:11 | Seat Height Motor Relay: Circuit Short To Ground | This DTC sets when the DSM detects the rear height motor relay (integral to the DSM ) is stuck or a short to ground is present in the rear height motor output circuit. |
| B1B86:15 | Seat Height Motor Relay: Circuit Short To Battery or Open | This DTC sets when the DSM detects the rear height motor relay (integral to the DSM ) is stuck or a short to voltage is present in the rear height motor output circuit. |
| B1B87:31 | Seat Height Motor Speed/Position Sensor: No Signal | This DTC sets when the DSM does not receive any signal from the Hall-effect sensor, integral to the rear height motor. |
| B1B88:11 | Seat Slide Motor Relay: Circuit Short To Ground | This DTC sets when the DSM detects the horizontal motor relay (integral to the DSM ) is stuck or a short to ground is present in the horizontal motor output circuit. |
| B1B88:15 | Seat Slide Motor Relay: Circuit Short To Battery or Open | This DTC sets when the DSM detects the horizontal motor relay (integral to the DSM ) is stuck or a short to voltage is present in the horizontal motor output circuit. |
| B1B89:31 | Seat Slide Motor Speed/Position Sensor: No Signal | This DTC sets when the DSM does not receive any signal from the Hall-effect sensor, integral to the horizontal motor. |
| B1B90:11 | Seat Tilt Motor Relay: Circuit Short To Ground | This DTC sets when the DSM detects the front height motor relay (integral to the DSM ) is stuck or a short to ground is present in the front height motor output circuit. |
| B1B90:15 | Seat Tilt Motor Relay: Circuit Short To Battery or Open | This DTC sets when the DSM detects the front height motor relay (integral to the DSM ) is stuck or a short to voltage is present in the front height motor output circuit. |
| B1B91:31 | Seat Tilt Motor Speed/Position Sensor: No Signal | This DTC sets when the DSM does not receive any signal from the Hall-effect sensor, integral to the front height motor. |
| B1B92:11 | Seat Recline Motor Relay: Circuit Short To Ground | This DTC sets when the DSM detects the recline motor relay (integral to the DSM ) is stuck or a short to ground is present in the recline motor output circuit. |
| B1B92:15 | Seat Recline Motor Relay: Circuit Short To Battery or Open | This DTC sets when the DSM detects the recline motor relay (integral to the DSM ) is stuck or a short to voltage is present in the recline motor output circuit. |
| B1B93:31 | Seat Recline Motor Speed/Position Sensor: No Signal | This DTC sets when the DSM does not receive any signal from the Hall-effect sensor, integral to the recline motor. |
| B1B94:24 | Seat Height Up Switch: Signal Stuck High | This DTC sets when the DSM detects the rear height control switch is stuck in the up position or a short to ground is present on the rear height switch input circuit for greater than 30 seconds. |
| B1B95:24 | Seat Height Down Switch: Signal Stuck High | This DTC sets when the DSM detects the rear height control switch is stuck in the down position or a short to ground is present on the rear height switch input circuit for greater than 30 seconds. |
| B1B96:24 | Seat Slide Forward Switch: Signal Stuck High | This DTC sets when the DSM detects the horizontal control switch is stuck in the forward position or a short to ground is present on the horizontal switch input circuit for greater than 30 seconds. |
| B1B97:24 | Seat Slide Backward Switch: Signal Stuck High | This DTC sets when the DSM detects the horizontal control switch is stuck in the rearward position or a short to ground is present on the horizontal switch input circuit for greater than 30 seconds. |
| B1B98:24 | Seat Tilt Up Switch: Signal Stuck High | This DTC sets when the DSM detects the front height control switch is stuck in the up position or a short to ground is present on the front height switch input circuit for greater than 30 seconds. |
| B1B99:24 | Seat Tilt Down Switch: Signal Stuck High | This DTC sets when the DSM detects the front height control switch is stuck in the down position or a short to ground is present on the front height switch input circuit for greater than 30 seconds. |
| B1C00:24 | Seat Recline Up Switch: Signal Stuck High | This DTC sets when the DSM detects the recline control switch is stuck in the up position or a short to ground is present on the recline switch input circuit for greater than 30 seconds. |
| B1C01:24 | Seat Recline Down Switch: Signal Stuck High | This DTC sets when the DSM detects the recline control switch is stuck in the down position or a short to ground is present on the recline switch input circuit for greater than 30 seconds. |
DTC FAULT TRIGGER CONDITIONS
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
| DTC | Description | Fault Trigger Conditions |
|---|---|---|
| B1C03:24 | Memory #1 Switch: Signal Stuck High | This DTC sets when the DSM detects the memory 1 switch is stuck in the active position or a short to ground is present on the memory switch input circuit for greater than 30 seconds. |
| B1C04:24 | Memory #2 Switch: Signal Stuck High | This DTC sets when the DSM detects the memory 2 switch is stuck in the active position or a short to ground is present on the memory switch input circuit for greater than 30 seconds. |
| B1C05:24 | Memory #3 Switch: Signal Stuck High | This DTC sets when the DSM detects the memory 3 switch is stuck in the active position or a short to ground is present on the memory switch input circuit for greater than 30 seconds. |
DTC FAULT TRIGGER CONDITIONS
Voltage to the heated seat control switch is supplied from a common circuit. The driver and passenger heated seat modules receive power from the accessory relay whenever the ignition is in the ON position.
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
| DTC | Description | Fault Trigger Conditions |
|---|---|---|
| U0140:00 | Lost Communication With Body Control Module BCM: No Sub Type Information | This DTC sets when the DSM detects data messages received from the BCM over the MS-CAN are missing for a short period of time or longer. |
DTC FAULT TRIGGER CONDITIONS
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
| DTC | Description | Fault Trigger Conditions |
|---|---|---|
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | This DTC sets when the DSM detects battery voltage below 10 volts. |
DTC FAULT TRIGGER CONDITIONS
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
| DTC | Description | Fault Trigger Conditions |
|---|---|---|
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | This DTC sets when the DSM detects battery voltage above 16 volts. |
DTC FAULT TRIGGER CONDITIONS
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
| DTC | Description | Fault Trigger Conditions |
|---|---|---|
| U0199:00 | Lost Communication With "Door Control Module A": No Sub Type Information | This continuous DTC sets in the DSM if data messages received from the DDM over the MSCAN are missing for 10 seconds or more. |
DTC FAULT TRIGGER CONDITIONS
Refer to: FRONT SEATS - SYSTEM OPERATION AND COMPONENT DESCRIPTION.
| DTC | Description | Fault Trigger Conditions |
|---|---|---|
| P1188:54 | Calibration Memory: Missing Calibration | This DTC can be set in the DSM if the seat calibration routine has not been completed successfully. |
| U1A4C:00 | Build/End of Line Mode Active: No Sub Type Information | This DTC can be set in the DSM if the seat calibration routine has not been completed successfully. |
DTC FAULT TRIGGER CONDITIONS
| DTC | Description | Fault Trigger Conditions |
|---|---|---|
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC can be set in the DSM if the seat calibration routine has not been completed successfully. |
DTC DESCRIPTION