Home ReviewsRefund
Home/Ford/Focus/Ford Focus III (2011-2015)/Repair manual/Communication Devices/Multifunction Electronic Modules -- Electric: Removal & Ins…
Contents Wiring diagrams Section: Communication Devices All sections

Multifunction Electronic Modules -- Electric: Removal & Installation Ford Focus III

Communication Devices ~1023 words

Removal

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test B

B2 BCM
  1. NOTE: If installing a new BCM , verify at least 2 of the vehicle keys are available prior to carrying out this procedure.
  2. NOTE: If installing a new module, it is necessary to upload the module configuration information to the scan tool prior to removing the module. This information must be downloaded into the new module after installation.
  3. Upload the module configuration information from the BCM into the scan tool by following the scan tool on screen instructions. For additional information, Refer to: «MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION»(ref-566933-S06601688372013071700000) (418-01 Module Configuration, Description and Operation).
B4 RH
B6 BCM

Installation

Pinpoint Test B

B1 BCM
  1. NOTE: The BCM still communicates with the scan tool with the ignition off. Use the previous scan tool session or start a new scan tool session using the PCM part number or tear tag number located on the PCM . The tear tag can be found by double-clicking the VIN in the top left corner of PTS after OASIS has been run for the VIN .
  2. NOTE: Low vehicle battery state of charge can affect proper module programming. Battery state of charge can be monitored on the scan tool. A red battery icon would indicate low vehicle battery state of charge. Over voltage may also affect module programming.
  3. NOTE: Make sure the battery is fully charged before starting the installation procedure. Do not have a battery charger connected to the vehicle charging system during the installation procedure.
  4. NOTE: Carry out Steps 2- 15 only if installing a new BCM .
  5. To install, reverse the removal procedure.
B2 PMI
B5 OASIS
  1. NOTE: If a diagnostic scan tool is connected to the internet, it will automatically obtain As-Built data. If a diagnostic scan tool is not connected to the internet, obtain the As-Built data from Professional Technician Society (PTS) OASIS . Download the As-Built data to the scan tool or other storage device, such as a flash drive, following the on-screen instructions.
  2. From the Car Configuration screen select "Retrieve PTS derived ASBUILT data". Follow the on-screen instructions to install the as-built data into the BCM .
B7 PATS
  1. NOTE: Due to Intelligent Access (IA), key transponder internal location, proper key orientation is required for successful key programming. Transponder location is on right side of steering column.
  2. Turn ignition on. On vehicles with IA, place the IA key in the PATS transceiver slot.
B9 PCM
  1. NOTE: If a tear tag or PCM part number was used to establish the scan tool session, it may be necessary to now establish a new session using the normal process.
  2. Using a scan tool, enter the PATS Functions and follow the on-screen instructions to enter PATS security access.
B10 BCM
B11 PATS
  1. NOTE: PATS security access may need to be granted again.
  2. Select parameter reset BCM and PCM . Follow the on-screen instructions.
B12 419-01
  1. Refer to: «ERASE ALL KEYS AND KEY PROGRAMMING»(ref-566977-S42821932052013071700000) ( 419-01 Passive Anti-Theft System (PATS) - Vehicles Without: Keyless Entry and Push Button Start).
  2. Refer to: «ERASE ALL KEYS AND KEY PROGRAMMING»(ref-566977-S42821932052013071700000) ( 419-01 Passive Anti-Theft System (PATS) - Vehicles With: Keyless Entry and Push Button Start).
B15 BCM

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test B

B2 RFA
  1. NOTE: If installing a new RFA module, verify at least 2 of the vehicle keys are available prior to carrying out this procedure.
B3 LH
B4 RFA
  1. NOTE: 4-door sedan is shown, 5-door hatchback is similar.
  2. Remove the RFA module.

Pinpoint Test B

B1 RFA
  1. NOTE: 4-door sedan is shown, 5-door hatchback is similar.
  2. NOTE: If installing a new RFA module, the ignition cannot be turned ON until a parameter reset is performed and 2 keys are programmed to the vehicle. The RFA module still communicates with the scan tool with the ignition off. Use the previous scan tool session or start a scan tool session using the PCM part number or tear tag.
  3. Install the RFA module.
B3 RFA
  1. Refer to: «PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET»(ref-566977-S35003004472013071700000) (419-01B Passive Anti-Theft System (PATS), General Procedures).
B4 RFA
  1. Refer to: «KEY PROGRAMMING USING DIAGNOSTIC EQUIPMENT»(ref-566977-S37067800162013071700000) (419-01B Passive Anti-Theft System (PATS), General Procedures).
B5 RFA

Note. Removal steps in this procedure may contain installation details.

  1. WARNING: Before beginning any service procedure in this information, refer to Safety Warnings in 100-00 General Information. Failure to follow this instruction may result in serious personal injury. Refer to: «HEALTH AND SAFETY PRECAUTIONS»(ref-566930-S09442017172013071700000) (100-00 General Information, Description and Operation).
  2. Remove the door trim panel. Refer to: «FRONT DOOR TRIM PANEL»(ref-566986-S05858706212013071700000) (501-05 Interior Trim and Ornamentation, Removal and Installation). Refer to: «REAR DOOR TRIM PANEL»(ref-566986-S15800358302013071700000) (501-05 Interior Trim and Ornamentation, Removal and Installation).
  3. Torque: 2 Nm
  1. To install, reverse the removal procedure.

More articles — Multifunction Electronic Modules -- Electric