Sunroof: Other Ford Focus I facelift

Roof Opening Panel

The roof opening panel consists of the following components

1. Roof opening panel switch
2. Air deflector
3. Roof opening panel glass
4. Roof opening panel weatherstrip
5. Roof opening panel frame
6. Roof opening panel shield
7. Roof opening panel motor
8. Roof opening panel front and rear drain hoses

Special Tools Illustration Tool Name Tool Number 73III Automotive Meter 105-R0057 or equivalent Flex Probe Kit 105-R025B or equivalent

Scheme 8

Roof Opening Panel Switch

1. Measure the resistance between the following: Roof Opening Panel Switch Position Pins Measurement Neutral 1 - 5 Greater than 10,000 ohms Neutral 2 - 6 Greater than 10,000 ohms Neutral 5 - 6 Greater than 10,000 ohms Neutral 6 - 1 Greater than 10,000 ohms Fully Up/Close 5 - 6 Less than 100 ohms Fully Up/Close 5 - 1 Greater than 10,000 ohms Fully Up/Close 5 - 2 Less than 100 ohms Fully Up/Close 2 - 6 Less than 100 ohms Fully Down/Open 2 - 6 Less than 100 ohms Fully Down/Open 2 - 5 Less than 100 ohms Fully Down/Open 5 - 6 Less than 100 ohms Fully Down/Open 2 - 1 Greater than 10,000 ohms
2. Apply battery voltage to the roof opening panel control switch C9014-1, component side, and ground to the roof opening panel control switch C9014-6, component side. The LED should illuminate.
3. If all measurements of the roof opening panel control switch are as shown, return to the pinpoint test. Otherwise, install a new roof opening panel control switch.

Updating Roof Opening Panel Motor Initialization

Note. This procedure should only be carried out when the roof opening panel motor is not disconnected.

Note. The roof opening panel alignment must be carried out prior to carrying out roof opening panel motor initialization. For additional information, refer to Roof Opening Panel Alignment .

1. Operate the roof opening panel control switch to the up/close position until the roof opening panel is in the fully open/vent position.
2. Release the roof opening panel control switch.
3. Press the roof opening panel control switch in the up/close position and hold for 30 seconds until there is a small movement of approximately 2 mm (0.08 in) and the roof opening panel motor stops.
4. Release the roof opening panel control switch.
5. Press the roof opening panel control switch in the up/close position again within 0.5 second until the roof opening panel stops (1 complete cycle).

Initial Roof Opening Panel Motor Initialization

Note. This procedure must be carried out when installing any roof opening panel motor or roof opening panel.

Note. The roof opening panel alignment must be carried out prior to carrying out the roof opening panel motor initialization. For additional information, refer to Roof Opening Panel Alignment .

1. Operate the roof opening panel control switch to the up/close position.
2. Release the roof opening panel control switch.
3. Operate the roof opening panel control switch to the up/close position again within 0.5 second until the roof opening panel stops (1 complete cycle).

Erasing Roof Opening Panel Motor Initialization

Note. The erasing procedure is to be carried out only when the roof opening panel motor is removed from the roof opening panel.

Note. This procedure must be carried out before installing a previously used roof opening panel motor.

1. Connect the roof opening panel motor electrical connector.
2. Operate the roof opening panel control switch to the up/close position until the roof opening panel motor stops.
3. Release the roof opening panel control switch.
4. Operate the roof opening panel control switch again to the up/close position and hold for 30 seconds. With the roof opening panel control switch held, the roof opening panel motor rotates in 1 direction.
5. Release the roof opening panel control switch.
6. Operate the roof opening panel control switch to the down/open position. If the roof opening panel motor does not rotate, the erasing procedure has been carried out successfully.
7. If the roof opening panel motor rotates (with the roof opening panel control switch in the down/open position), repeat the procedure.

Scheme 9

1. For additional information, refer to the appropriate procedures.