General Specifications
| Clutch | |
|---|---|
| Clutch 1 | 26 mm (1.023 in) |
| Clutch 2 | 15 mm (0.59 in) |
GENERAL SPECIFICATIONS
| Synchronizer Ring Clearance | |
|---|---|
| Clearance Between Synchronizer Ring and Flank Surface of Gear | |
| Minimum | 1.00 mm (0.039 in) |
GENERAL SPECIFICATIONS
| Shift Fork and Hub Sleeve Clearance | |
|---|---|
| Reverse/4th Gear Shift Fork and Hub Sleeve | |
| Maximum | 1.85 mm (0.072 in) |
| Standard | 0.75-1.25 mm (0.029-0.049 in) |
| Clearance Between 1st/5th Shift Fork and Hub Sleeve | |
| Maximum | 1.85 mm (0.072 in) |
| Standard | 0.75-1.25 mm (0.029-0.049 in) |
| Clearance Between 3rd Gear Shift Fork and Hub Sleeve | |
| Maximum | 1.725 mm (0.067 in) |
| Standard | 0.625-1.125 mm (0.024-0.044 in) |
| Clearance Between 2nd/6th Shift Fork and Hub Sleeve | |
| Maximum | 1.725 mm (0.067 in) |
| Standard | 0.625-1.125 mm (0.024-0.044 in) |
GENERAL SPECIFICATIONS
| Gear Clearance | |
|---|---|
| 1st Gear | |
| Radial Clearance Maximum | 0.055 mm (0.002 in) |
| Axial Clearance Maximum | 0.645 mm (0.025 in) |
| 2nd Gear | |
| Radial Clearance Maximum | 0.055 mm (0.002 in) |
| Axial Clearance Maximum | 0.495 mm (0.019 in) |
| 3rd Gear | |
| Radial Clearance Maximum | 0.055 mm (0.002 in) |
| Axial Clearance Maximum | 0.595 mm (0.023 in) |
| 4th Gear | |
| Radial Clearance Maximum | 0.055 mm (0.002 in) |
| Axial Clearance Maximum | 0.625 mm (0.024 in) |
| 5th Gear | |
| Radial Clearance Maximum | 0.055 mm (0.002 in) |
| Axial Clearance Maximum | 0.52 mm (0.02 in) |
| 6th Gear | |
| Radial Clearance Maximum | 0.055 mm (0.002 in) |
| Axial Clearance Maximum | 0.51 mm (0.02 in) |
| Reverse Gear | |
| Radial Clearance Maximum | 0.073 mm (0.002 in) |
| Axial Clearance Maximum | 0.59 mm (0.023 in) |
GENERAL SPECIFICATIONS
Torque Specifications
| Description | N.m | Lb. ft. | Lb. in. |
|---|---|---|---|
| Battery tray bolts | 10 | 89 | |
| Battery tray bracket bolts | 10 | 89 | |
| Brake hose retainer bolts | 25 | 18 | |
| Center bearing bracket nuts (1) | |||
| Clutch actuator lever bolts | 19 | 168 | |
| Clutch actuator lever spring retainer bolts () | |||
| Clutch housing-to-case bolts | 27 | 20 | |
| Clutch housing-to-engine bolts | 48 | 35 | |
| Clutch motor bolts | 5 | 44 | |
| Differential ring gear bolts (1) | |||
| Drain plug | 43 | 32 | |
| Exhaust flange nuts | 48 | 35 | |
| Fill plug | 43 | 32 | |
| Flexplate-to-clutch nuts () | |||
| Ground wire bolt | 25 | 18 | |
| Guide tube bolts | 8 | 71 | |
| Input shaft bearing retainer bolts | 11 | 97 | |
| Input shaft speed sensor bolt | 10 | 89 | |
| Lower control arm knuckle bolts | 48 | 35 | |
| Manual control lever bolt | 26 | 19 | |
| Output shaft bearing retainer bolts | 32 | 24 | |
| Output Shaft Speed (OSS) sensor bolt | 10 | 89 | |
| Park plunger plug | 43 | 32 | |
| Roll restrictor-to-transaxle bracket bolt | 48 | 35 | |
| Roll restrictor bolt | 70 | 52 | |
| Selector lever battery tray bracket bolt | 25 | 18 | |
| Selector lever cable bracket bolts | 10 | 89 | |
| Shim selection tool bolts | 18 | 159 | |
| Strut mount nuts | 48 | 35 | |
| Transaxle support insulator bracket bolts | 90 | 66 | |
| Transaxle support insulator bracket nuts | 125 | 92 | |
| Transmission Control Module (TCM) | 27 | 20 | |
| Transmission Range (TR) sensor bolts | 10 | 89 | |
| (1) Refer to the appropriate procedure in this information. | |||
| (1) | Refer to the appropriate procedure in this information. |
TORQUE SPECIFICATIONS
See also:
• JACKING AND LIFTING