GENERAL SPECIFICATIONS
| Item | Specification |
|---|---|
| Displacement | 2.3L |
| No. of cylinders | 4 |
| Bore/stroke | 87.5/94.0 |
| Firing order | 1 - 3--4-2 |
| Oil pressure (hot @ 2,000 rpm) | 29 - 39 psi 200 - 268 kPa |
| Oil capacity | 4.1 qts. + 0.4 qt. with filter |
| Cylinder Block | |
| Cylinder bore diameter | 87.5 - 87.53 mm (3.444 - 3.446 in.) |
| Cylinder bore maximum out-of-round | 0.008 mm (0.0003 in.) |
| Main bearing bore diameter | 57.020 - 57.038 mm (2.244 - 2.245 in.) |
| Head gasket surface flatness | 0.1 mm/general 0.05 mm/200 x 200 (0.004 in./general) (0.0019 in./7.87 x 7.87) |
| Piston | |
| Diameter (1) | 87.5 - 87.51 mm (3.444 - 3.445 in.) |
| Diameter (2) | 87.51 - 87.52 mm (3.4452 - 3.4456 in.) |
| Diameter (3) | 87.52 - 87.53 mm (3.445 - 3.446 in.) |
| Piston-to-bore clearance | 0.025 - 0.045 mm (0.0009-0.0017 in.) |
| Ring groove width - top | 1.203 - 1.205 mm (0.0473-0.0474 in.) |
| Ring groove width - 2nd | 1.17 - 1.19 mm (0.0460 - 0.0468 in.) |
| Ring groove width - oil | 2.501 - 2.503 mm (0.0984-0.0985 in.) |
| Piston skirt coating thickness | 0.008 - 0.020 mm (0.0003 - 0.0007 in.) |
| Piston Pin | |
| Diameter | 20.995 - 21.0 mm (0.8265 - 0.8267 in.) |
| Length | 59.6 - 60.4 mm (2.346 - 2.377 in.) |
| Piston-to-pin clearance | 0.008 - 0.016 mm (0.0003 - 0.0006 in.) |
| Pin-to-rod clearance | Press fit |
| Cylinder Head | |
| Valve lift @ zero lash (exhaust) | 7.4 mm (0.29 in) |
| Valve lift @ zero lash (intake) | 7.9 mm (0.31 in) |
| Valve guide diameter | 5.509 - 5.539 mm (0.216 - 0.218 in.) |
| Valve seat width - intake/exhaust | 0.99 - 1.84 mm (0.038-0.072 in.) |
| Valve seat angle | 45 degrees |
| Valve seat runout | 0.075 mm (0.0029 in.) |
| Valve lash adjuster bore diameter | 31.00 - 31.03 mm (1.220 - 1.221 in.) |
| Cam bore diameter | 25.015 - 25.040 mm (0.984 - 0.985 in.) |
| Valve | |
| Valve head diameter - intake | 34.85 - 35.15 mm (1.372 - 1.383 in.) |
| Valve head diameter - exhaust | 29.85 - 30.15 mm (1.175 - 1.187 in.) |
| Valve stem diameter - intake | 5.470 - 5.485 mm (0.2153 - 0.2159 in.) |
| Valve stem diameter - exhaust | 5.465 - 5.480 mm (0.2151 - 0.2157 in.) |
| Valve stem-to-guide clearance - intake | 0.0027 mm (0.00010 in.) |
| Valve stem-to-guide clearance - exhaust | 0.0029 mm (0.00011 in.) |
| Valve face runout | 0.05 mm (0.0019 in.) |
| Valve face angle | 45 degrees |
| Valve Spring - Compression Pressure | |
| Intake and exhaust (installed) | 38.667 lb |
| Intake (valve open) 8.9 mm (0.35 in.) of lift | 97.032 lb |
| Exhaust (valve open) 7.4 mm of lift | 93.338 lb |
| Free length | 44.92 mm (1.768 in.) |
| Assembled height | 37.9 mm (1.492 in.) |
| Crankshaft | |
| Main bearing journal diameter | 51.980 - 52.000 mm (2.046 - 2.047 in.) |
| Production repair | 51.730 - 51.750 mm (2.036 - 2.037 in.) |
| Main bearing clearance | 0.019 - 0.035 mm (0.0007 - 0.0013 in.) |
| Connecting rod journal diameter | 49.980 - 50.000 mm (1.967 - 1.968 in.) |
| Production repair | 49.730 - 49.750 mm (1.957 - 1.958 in.) |
| End play | 0.22 - 0.43 mm (0.008 - 0.016 in.) |
| Rings | |
| Width - top | 1.17 - 1.185 mm (0.0460 - 0.0466 in.) |
| Width - 2nd | 1.197 - 1.199 mm (0.047 - 0.0472 in.) |
| Width - oil | 2.38 - 2.45 mm (0.093 - 0.096 in.) |
| Ring gap (in bore) - top | 0.16 - 0.31 mm (0.006 - 0.012 in.) |
| Ring gap (in bore) - 2nd | 0.33 - 0.48 mm (0.012 - 0.018 in.) |
| Ring gap (in bore) - oil | 0.2 - 0.7 mm (0.007 - 0.027 in.) |
| Valve Tappet | |
| Diameter | 30.97 - 30.98 mm (1.2192 - 1.2196 in.) |
| Tappet-to-valve clearance - intake | 0.22-- 0.28 mm (0.008 - 0.011 in.) |
| Tappet-to-valve clearance - exhaust | 0.27 - 0.33 mm (0.010 - 0.013 in.) |
| Tappet-to-bore clearance | 0.02 - 0.06 mm (0.0007 - 0.0023 in.) |
| Camshaft | |
| Lobe lift - intake | 8.24999 mm (0.324 in.) |
| Lobe lift - exhaust | 7.80007 mm (0.307 in.) |
| Runout (1) (1) | 0.03 mm (0.001 in.) |
| Thrust clearance | 0.09 - 0.24 mm (0.003 - 0.009 in.) |
| Journal diameter | 24.96 - 24.98 mm (0.982 - 0.983 in.) |
| Journal-to-bore clearance | 0.035 - 0.080 mm (0.001 - 0.003 in.) |
| Connecting Rod | |
| Bearing clearance | 0.027 - 0.052 mm (0.001 - 0.002 in.) |
| Bearing thickness | 1.496 - 1.520 mm (0.058 - 0.059 in.) |
| Crank bore diameter | 53.025 - 53.045 mm (2.087 - 2.088 in.) |
| Pin bore diameter | 20.965 - 20.985 mm (0.825 - 0.826 in.) |
| Length (center-to-center) | 154.8 mm (6.094 in.) |
| Side clearance | 1.95 - 3.05 mm (0.076 - 0.120 in.) |
| Axial clearance | 0.14 - 0.36 mm (0.005 - 0.014 in.) |
| Motorcraft Metal Surface Cleaner ZC-21 | WSE-M5B392-A |
| Silicone Gasket Remover ZC-30 | |
| Motorcraft Metal Surface Prep ZC-31 | |
| Silicone Gasket and Sealant TA-30 | WSE-M4G323-A4 |
| High Temperature 4x4 Front Axle and Wheel Bearing Grease E8TZ-19590-A | ESA-M1C198-A |
| Silicone Brake Caliper Grease and Dielectric Compound XG-3-A | ESE-M1C171-A |
| Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP (in Canada Motorcraft SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12) or equivalent | WSS-M2C930-A |
| Motorcraft Premium Gold Engine Coolant VC-7-A (in California, Oregon and New Mexico VC-7-B, in Canada CVC-7-A) or equivalent (yellow color) | WSS-M97B51-A1 |
| Multi-Purpose Grease XL-5, XG-4 | ESB-M1C93-B |
| Thread Sealant with PTFE TA-24 | WSK-M2G350-A2 |
| (1) No. 3 Journal - Supported by No. 1 and No. 5 journals. | |
| (1) | No. 3 Journal - Supported by No. 1 and No. 5 journals. |
GENERAL SPECIFICATIONS
TORQUE SPECIFICATIONS
| Description | Nm | Lb-ft | Lb-in |
|---|---|---|---|
| Camshaft bearing cap bolts (1) | |||
| Coolant outlet bolts | 25 | 18 | |
| Oil pan bolts (1) | |||
| Oil pump-to-engine block bolts (1) | |||
| Cylinder head bolts (1) | |||
| Accelerator cable snow shield bolts | 10 | 89 | |
| Intake manifold bolts | 18 | 13 | |
| Flexplate bolts (1) | |||
| Flywheel bolts (1) | |||
| Crankshaft pulley bolt (1) | |||
| Crankshaft position (CKP) sensor bolts | 7 | 62 | |
| Rear crankshaft oil seal retainer bolts (1) | |||
| A/C compressor mounting bolts | 25 | 18 | |
| Oil pump sprocket bolt | 25 | 18 | |
| Knock sensor (KS) bolt | 20 | 15 | |
| Engine mount bracket bolts | 90 | 66 | |
| Engine mount bolts | 55 | 41 | |
| Engine roll-restrictor bolts | 90 | 66 | |
| Engine-to-transmission bolts | 48 | 35 | |
| Starter motor mounting bolts | 25 | 18 | |
| Torque converter-to-flywheel nuts | 35 | 26 | |
| Power steering pressure (PSP) tube nut | 20 | 15 | |
| Powertrain control module (PCM) wiring connector bolt | 6 | 53 | |
| Coolant pump bolts | 10 | 89 | |
| Engine front cover bolts (1) | |||
| Camshaft sprocket bolt | 65 | 48 | |
| Valve cover bolts | 10 | 89 | |
| Exhaust gas recirculation (EGR) valve assembly bolts | 25 | 1 | |
| Thermostat housing bolts | 10 | 89 | |
| Oil pump screen and cover assembly bolts | 10 | 89 | |
| Catalytic converter studs | 17 | 13 | |
| Catalytic converter-to-cylinder head nuts | 47 | 35 | |
| Coolant pump pulley bolts | 25 | 18 | |
| Generator mounting bolts | 48 | 35 | |
| Power steering pump mounting bolts | 25 | 18 | |
| A/C compressor mounting bolts | 48 | 35 | |
| Oil level indicator tube bolt | 10 | 89 | |
| Oil pressure sensor | 15 | 11 | |
| A/C manifold tube bolt | 20 | 15 | |
| Oil drain plug | 28 | 21 | |
| Oil pump chain tensioner bolts | 10 | 89 | |
| Oil pump chain guide bolts | 10 | 89 | |
| Timing chain guide bolts | 10 | 89 | |
| Timing chain tensioner bolts | 10 | 89 | |
| Crankcase vent oil separator bolts | 10 | 89 | |
| Oil filter adapter bolts | 25 | 18 | |
| Oil cooler bolt | 34 | 25 | |
| Air cleaner outlet tube clamps | 3 | 27 | |
| Coil-on-plug retaining stud bolts | 10 | 89 | |
| Engine timing plug bolt | 20 | 15 | |
| Belt tensioner bolt | 25 | 18 | |
| Oil filter cup | 33 | 24 | |
| Oil pan-to-bell housing bolts | 48 | 35 | |
| Rear main seal mounting plate bolts | 10 | 89 | |
| Camshaft position (CMP) sensor bolt | 20 | 15 | |
| Cylinder head temperature (CHT) sensor | 12 | 9 | |
| Spark plug | 15 | 11 | |
| Fuel rail bolts | 10 | 89 | |
| Pressure plate bolts | 32 | 24 | |
| (1) Refer to appropriate procedure under IN-VEHICLE REPAIR for specification. | |||
| (1) | Refer to appropriate procedure under IN-VEHICLE REPAIR for specification. |
TORQUE SPECIFICATIONS
The 2.3L engine is a 4 valve-per-cylinder, dual overhead camshaft engine. The engine uses a coil-on-plug ignition system. The cylinder block is made of aluminum and the bearing caps are integrated into the ladder assembly. An aluminum oil pan bolts to the bottom of the lower cylinder block and to the transmission to provide greater strength. The camshafts are mounted in the cylinder heads and act against valve tappets to open and close the valves. The camshafts are driven off the front of the cylinder head by one timing chain. The chain is driven by a sprocket that is located on the crankshaft. The piston assembly is an aluminum piston with a cast iron connecting rod. The oil pump is driven by the crankshaft via a dedicated chain that is driven by the same sprocket that drives the timing chain.
Refer to ENGINE SYSTEM-GENERAL INFORMATION for basic mechanical concerns or refer to INTRODUCTION - GASOLINE article for driveability concerns.
See also:
• JACKING AND LIFTING
• ENGINE BLOCK - 2.3L