Sunroof: Other Ford Edge I

Roof Opening Panel

The roof opening panel consists of the following

1. Air deflector
2. Concertina blinds
3. Fixed glass front seal
4. Fixed glass side seals
5. Front shade assembly
6. Front trim panel
7. Front trim panel seal
8. Guide track and mechanism
9. Idler track and mechanism
10. Motor wiring harness
11. Overhead console control switch
12. Rear shade assembly
13. Roof opening panel fixed glass
14. Roof opening panel shade motor
15. Roof opening panel sliding glass
16. Roof opening panel sliding glass motor
17. Rear trim ring assembly
18. Shade motor block and drive tube assembly
19. Shade track and mechanism
20. Sliding front panel motor block and drive tube assembly
21. Sliding glass primary seal
22. Side trim panel
23. Side trim panel seals

The roof opening panel consists of an electronically operated sliding glass panel and electronically operated sunshades that can be opened or closed by pressing a switch located on the overhead console. The sliding glass panel has one-touch open, one-touch close and one-touch vent open features. The shades have a one-touch-open feature.

The front and rear shades operate together with a 80 mm (3.14 in) delay in the closing of the rear shade to the front. The sunshade may be in any position when the sliding glass panel is in the closed position. The shades will open a proportional amount when the sliding glass panel is in any position between closed and fully open. With the sliding glass panel in the fully OPEN position, the shades are disabled to prevent wind damage.

When the sliding glass panel is in the fully CLOSED position, pressing the overhead console roof opening panel control switch rearward to the second detent and then releasing it will activate the one-touch open feature and the glass panel will open to the comfort position. Pressing the switch a second time will move the glass to the fully OPEN position. The one-touch open feature can be canceled any time the sliding glass is moving by pressing the roof opening panel control switch in either direction.

With the sliding glass panel in any open position except VENT, rocking the roof opening panel control switch forward and then releasing it will activate the one-touch close feature. Pressing the roof opening panel control switch in either direction with the roof opening panel moving will cancel the one-touch close operation and the motion will immediately stop.

If an obstacle contacts the leading edge of the sliding glass panel during one-touch close operation, the roof opening panel glass will reverse direction and open to approximately the mid position and stop. The operator cannot stop this open motion once it has begun.

If an obstacle contacts the leading edge of the roof opening panel glass during one-touch vent close operation, the roof opening panel glass will reverse direction to the VENT position.

When the sliding glass panel is in the fully CLOSED position, pressing the roof opening panel control tilt switch and then releasing it will activate the one-touch vent feature. To vent the sliding glass panel from any position, press and hold the tilt switch. To close, press and hold the roof opening panel control switch in the forward position.

Global Open - MKX Only - The smart junction box (SJB) sends a signal on the global open circuit, to the roof opening panel motor, to open or close the windows based on a signal received from the remote keyless entry (RKE) transmitter. If the accessory delay relay is active, the global open feature will not operate.

Special Tools Illustration Tool Name Tool Number 73III Automotive Meter 105-R0057 or equivalent

Roof Opening Panel Motor Initialization

Note. New roof opening panel glass motor/shade motors must be initialized after installation.

Note. An de-initialized glass or shade motor will stutter step open when their respective open switches are pressed.

Note. The glass close switch must be held during the entire initialization process or the sequence will be aborted and the roof will remain in a de-initialized state.

For a new drive assembly

Note. If installing a new roof opening panel shade motor assembly, use the existing drive assembly procedure.

1. Start the engine.
2. Press and hold the glass close switch. The glass panel will move toward the front hard-stop, stall and then move backward a few millimeters and then forward. The shade panels will move toward their front hard-stops, stall, move back a few millimeters, then forward. After the shade panels have finished moving backward and forward, release the glass close switch.
3. Repress and hold the glass close switch while the glass and shades fully open and fully close.
4. Initialization is now complete. Verify successful initialization by carrying out one-touch open, one-touch close, one-touch vent (glass) and one-touch open for the shades. If roof opening panel does not operate correctly, repeat Steps 2 through 4.
5. Start the engine.
6. Press and hold the glass close switch until the glass is in CLOSED position.
7. Release, repress and hold the glass close switch (for at least 10 seconds). The glass panel will move toward the front hard-stop and stall. The shade panels will move toward their front hard-stops, stall, move back a few millimeters, then forward. After the shade panels have finished moving backward and forward, release the glass close switch.
8. Press and hold the glass close switch. The glass and shades will fully open together. Then, the glass will close first and then the shades will return to the fully CLOSED position. When the shades have stopped moving, release the glass close switch.
9. Initialization is now complete. Verify successful initialization by carrying out one-touch open, one-touch close, one-touch vent (glass) and one-touch open for the shades. If roof opening panel does not operate correctly, repeat Steps 6 through 9.

Roof Opening Panel Glass - Rear Fixed

Special Tools Illustration Tool Name Tool Number The Pumper 164-R2459 or equivalent Rotunda Interior Auto Glass Cut-Out Knife Kit 164-R2450 or equivalent

Material

Roof Opening Panel Module

Special Tools Illustration Tool Name Tool Number Rotunda Interior Auto Glass Cut-Out Knife Kit 164-R2450 or equivalent

Material

Roof Opening Panel Trim - Front

Special Tools Illustration Tool Name Tool Number Rotunda Interior Auto Glass Cut-Out Knife Kit 164-R2450 or equivalent

Material

Roof Opening Panel Trim - Side

Special Tools Illustration Tool Name Tool Number Rotunda Interior Auto Glass Cut-Out Knife Kit 164-R2450 or equivalent

Material