Home ReviewsRefund
Home/Ford/C-MAX/Ford C-MAX II (2010-2015)/Repair manual/Collision/avoidance/Parking Aid System: Removal & Installation
Contents Wiring diagrams Section: Collision/avoidance All sections

Parking Aid System: Removal & Installation Ford C-MAX II

Collision/avoidance 2 illustrations ~561 words

Removal

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test A

A2 PAM
  1. NOTE: Module configuration is required when a new parking assist control module (PAM) is being installed.
  2. If a new module is being installed, upload the module configuration information from the PAM into the scan tool by following the instructions on the scan tool.
A3 RH
  1. Refer to: «LOADSPACE TRIM PANEL RH»(ref-635245-S25097144162014070200000) .

Installation

Pinpoint Test A

A2 PAM

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test A

A3 RH
  1. Refer to: «LOADSPACE TRIM PANEL RH»(ref-635245-S25097144162014070200000) .
  1. To install, reverse the removal procedure.
  2. If a new module has been installed, download the IPM-B configuration information from the scan tool to the new IPM-B.

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test A

A2 RH
  1. NOTE: The LH front inner park aid sensor is shown, the RH front inner sensor is similar.
  2. Remove the front bumper cover.
  3. Refer to: «FRONT BUMPER COVER»(ref-635263-S25966551712014070200000) .
  1. To install, reverse the removal procedure.
  2. Carry out the azimuth and elevation system checks. Refer to: «AZIMUTH SYSTEM CHECK»(ref-635201-S26118771842014070200000) . Refer to: «ELEVATION SYSTEM CHECK»(ref-635201-S35746699802014070200000) .

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test A

A3 RH
  1. NOTE: The LH front outer park aid sensor is shown, the RH front outer sensor is similar.
  2. click to open the image
  1. To install, reverse the removal procedure.
  2. Carry out the azimuth and elevation system checks. Refer to: «AZIMUTH SYSTEM CHECK»(ref-635201-S26118771842014070200000) . Refer to: «ELEVATION SYSTEM CHECK»(ref-635201-S35746699802014070200000) .

Note. Removal steps in this procedure may contain installation details.

Scheme 2

Scheme 2: Removal
Scheme 2: Removal
  1. WARNING: Before beginning any service procedure in this article, refer to Safety Warnings in «GENERAL INFORMATION»(ref-635189) . Failure to follow this instruction may result in serious personal injury. Refer to: «HEALTH AND SAFETY PRECAUTIONS»(ref-635189-S18367805802014070200000) .
  2. Remove the rear bumper cover. Refer to: «REAR BUMPER COVER»(ref-635263-S39920235462014070200000) .
  1. To install, reverse the removal procedure.
  2. Carry out the azimuth and elevation system checks. Refer to: «AZIMUTH SYSTEM CHECK»(ref-635201-S26118771842014070200000) . Refer to: «ELEVATION SYSTEM CHECK»(ref-635201-S35746699802014070200000) .

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test A

A2 RH
  1. NOTE: The LH rear outer park aid sensor is shown, the RH rear outer sensor is similar.
  2. Remove the rear bumper cover.
  3. Refer to: «REAR BUMPER COVER»(ref-635263-S39920235462014070200000) .
  1. To install, reverse the removal procedure.
  2. Carry out the azimuth and elevation system checks. Refer to: «AZIMUTH SYSTEM CHECK»(ref-635201-S26118771842014070200000) . Refer to: «ELEVATION SYSTEM CHECK»(ref-635201-S35746699802014070200000) .

Note. Removal steps in this procedure may contain installation details.

Scheme 3

Scheme 3: Removal
Scheme 3: Removal
  1. WARNING: Before beginning any service procedure in this article, refer to Safety Warnings in «GENERAL INFORMATION»(ref-635189) . Failure to follow this instruction may result in serious personal injury. Refer to: «HEALTH AND SAFETY PRECAUTIONS»(ref-635189-S18367805802014070200000) .
  2. Refer to: «LIFTGATE TRIM PANEL»(ref-635245-S40810924252014070200000) .

Pinpoint Test A

A2 IPMB

More articles — Parking Aid System