Power Windows - Service Information: Other Dodge Journey I

EXPRESS DOWN WINDOW FEATURE

This feature allows you to remotely lower both front door windows at the same time. To use this feature, press and release the UNLOCK button on the RKE transmitter and then immediately press and hold the UNLOCK button until the windows lower to the desired level or until they lower completely.

CLEAR/RELEARN

Note. Make sure battery is fully charged before proceeding.

Note. This needs to be completed every time the window glass is adjusted/removed, motor replaced, and or regulator replaced.

CLEAR/DENORMALIZE USING A SCAN TOOL

To clear/denormalize the door module memory, using a scan tool under the Miscellaneous menu look for Denormalization Window Command/ECU reset, and follow the directions.

RELEARN/NORMALIZE USING A SCAN TOOL

To relearn/normalize the door module memory, using a scan tool under the Miscellaneous menu look for Normalization Window command, and follow the directions.

CLEAR/DENORMALIZE, RELEARN/NORMALIZE WITHOUT A SCAN TOOL

Hold up/down the window switch for at least 30 seconds until the DTC is set for stuck switch. This will clear the memory of the calibration information (CLEAR/DENORMALIZE). Proceed to relearn/normalize.

1. Put a battery charger on vehicle.
2. If equipped with express-up/express-down, reset the express-up/down module for the door window glass. The window switch on the corresponding door must be used to control the window. Do not use the master switch for the passenger window.
3. To calibrate, start by moving the window to the middle position.
4. Drive the glass to the full-up position by pulling up on the window switch to its second detent and hold the switch until the glass is fully closed. Do not release the window switch. Continue to hold the window switch up for 2 seconds after the window glass is full closed.
5. Drive the glass to the full - down position by pushing down (depress) the window switch, (second detent if equipped with express-down) until the window glass is down for 2 seconds after the window glass is fully open. Do not release the window switch. Continue to hold the window switch down for 2 seconds after the window glass is fully open.
6. Check the operation of the express-up/ express-down feature.
7. If the express up/down doesn't work, repeat step # 3, waiting for 3 seconds.
8. Check that the window glass reverses when in the express-up mode by holding a pen in the path of the glass.
9. Once the proper operation of the express-up/express-down feature has been verified, clear all Diagnostic Trouble Codes (DTC's).

WINDOW MOTOR

1. Remove door trim panel. Refer to «Body/Door - Front/PANEL, Door Trim - Removal»(ref-353577-S40808100392010011200000) .
2. Connect positive (+) lead from a test battery to either of the two motor terminals.
3. Connect negative (-) lead from test battery to remaining motor terminal.
4. The motor should now rotate in one direction to either move window up or down. If window happens to already be in full UP position and motor is connected so as to move it in UP direction no movement will be observed. Likewise, motor connected to move window in DOWN direction no movement will be observed if window is already in full DOWN position. Reverse battery leads in steps 1 and 2 and window should now move. If window does not move, replace motor.
5. If window moved completely up or down, the test leads should be reversed one more time to complete a full window travel inspection.
6. If window does not move, check to make sure that it is free.
7. It is necessary that the window be free to slide up and down in the glass channels. If the window is not free to move up and down, the window lift motor will not be able to move the glass.
8. To determine if the glass is free, disconnect the regulator from the glass lift plate. Remove the two attaching screws, and slide the window up and down by hand.

SWITCH - FRONT DOOR

1. Disconnect and isolate the battery negative remote cable.
2. Using a trim tool, or equivalent, carefully pry up on the window switch until it disengages from the door trim panel.
3. Disconnect switch wire connector.
4. Remove switch assembly.

SWITCH - REAR DOOR

1. Disconnect and isolate the battery negative cable.
2. Using a trim tool, or equivalent, carefully pry up on the window switch until it disengages from the door trim panel.
3. Disconnect the electrical connector.
4. Remove the switch from the handle.

1. Install the switch by snapping into place.
2. Connect switch wire connector.
3. Install the switch to the door trim panel.
4. Connect the battery negative cable.

1. Connect the electrical connector.
2. Install the switch to the door trim panel.
3. Connect the battery negative cable.