| Accelerator Pedal Position Sensor Retaining Bolts | 15 (20) |
| Battery Cable-To-Battery Bolt | 13 (17) |
| Engine Coolant Temperature Sensor | 15 (20) |
| EVAP Canister Mounting Bolts | 18 (25) |
| Fuel Composition Sensor Bracket-To-Frame Rail Mounting Nuts (5.3L Flex-Fuel) | 13 (17) |
| Fuel Line Fittings | 18 (25) |
| Fuel Tank Strap Retaining Bolts | 30 (40) |
| Generator Mounting Bolts | 37 (50) |
| Knock Sensors | 15 (20) |
| Oxygen Sensors | 31 (42) |
| Spare Tire Rear Crossmember Fasteners | 37 (50) |
| Spark Plugs |
| 4.8L, 5.3L & 6.0L | (1) |
| 8.1L | (2) |
| Starter Mounting Bolts (4.8L, 5.3L & 6.0L) | 37 (50) |
| INCH Lbs. (N.m) |
| Camshaft Position Sensor Retaining Bolt/Screws |
| 4.8L, 5.3L & 6.0L | (3) |
| 8.1L | 106 (12.0) |
| Crankshaft Position Sensor Retaining Bolt |
| 4.8L, 5.3L & 6.0L | (4) |
| 8.1L | 106 (12.0) |
| EVAP Canister Purge Solenoid Retaining Bolts/Nuts | 93 (10.5) |
| Fuel Composition Sensor-To-Mounting Bracket Bolts (5.3L Flex-Fuel) | 89 (10.0) |
| Fuel Fill & Vent Pipe Hose Clamps | 22 (2.5) |
| Fuel Filler Pipe Ground Strap Retaining Bolt (4.8L, 5.3L & 6.0L) | 80 (9.0) |
| Fuel Filter Bracket Retaining Bolt | 106 (12.0) |
| Fuel Rail Retaining Bolts |
| 4.8L, 5.3L & 6.0L | 89 (10.0) |
| 8.1L | 106 (12.0) |
| Generator Positive Post Cable Nut | 80 (9.0) |
| Ignition Coil Retaining Bolts |
| 4.8L, 5.3L & 6.0L | 71 (8.0) |
| 8.1L | 106 (12.0) |
| Intake Manifold Sight Shield Bracket/Retainer Bolts/Nuts (4.8L, 5.3L, 6.0L & 8.1L) | 44 (5.0) |
| Intake Manifold Sight Shield Fastener (4.8L, 5.3L, 6.0L & 8.1L) | 89 (10.0) |
| MAF Sensor Hose Clamps | 62 (7.0) |
| Manifold Absolute Pressure Sensor Retaining Bolt (8.1L) | 106 (12.0) |
| PCM Harness Connector Fasteners | 71 (8.0) |
| Positive Battery Cable-To-Solenoid Nut (4.8L, 5.3L & 6.0L) | 80 (9.0) |
| Starter Solenoid Start Lead Terminal Nut (4.8L, 5.3L & 6.0L) | 30 (3.4) |
| TAC Module Nuts | 80 (9) |
| Throttle Body Mounting Nuts (4.8L, 5.3L, 6.0L & 8.1L) | 89 (10.0) |
| Upper Engine Wiring Harness Retainer Nut (4.8L, 5.3L & 6.0L) | 44 (5.0) |
| (1) If cylinder heads have not been replaced, tighten spark plugs to 11 ft. lbs. (15 N.m). With NEW aluminum cylinder heads, tighten spark plugs to 15 ft. lbs. (20 N.m). With NEW iron cylinder heads, tighten spark plugs to 22 ft. lbs. (30 N.m). (2) If cylinder heads have not been replaced, tighten spark plugs to 15 ft. lbs. (20 N.m). With NEW iron cylinder heads, tighten spark plugs to 22 ft. lbs. (30 N.m). (3) Tighten to 21 ft. lbs. (29 N.m). (4) Tighten to 18 ft. lbs. (25 N.m). |
