Home ReviewsRefund
Home/Audi/A8/Audi A8 D2 facelift (1999-2002)/Repair manual/Exterior Body Panels/Bumper: Overview
Contents Wiring diagrams Section: Exterior Body Panels All sections

Bumper: Overview Audi A8 D2 facelift

Exterior Body Panels ~409 words

Front trim and spoiler, assembly overview

Note. The following list refers to (Схема №14).

  1. Bumper cover
  2. Trim Before removing, bumper must be removed. To remove, remove Philips-head screws -3- and -4-. Disengage locking lugs of retaining clamp and remove trim toward front. See «FRONT TRIM, REMOVING»(ref-196883-S05110146572005101000000) . Before installing trim, press retaining clamps into bumper cover
  3. Phillips-head screw
  4. Phillips-head screw
  5. Bumper carrier Removing: Remove clips -8- from upper and lower sides. See «CLIP FOR BUMPER COVER»(ref-196883-S04610777322006060600000) .
  6. Spoiler Removing: remove bumper. Remove hex bolt -7-. Remove clips from underside. See «CLIP FOR BUMPER COVER»(ref-196883-S04610777322006060600000) .
  7. Hex bolt 21 Nm
  8. Clip Qty: 15
  1. To remove, pull out locking pin -2- as shown.
  2. Remove clip -2- from bumper cover.
  3. To install, clip is pressed into bumper and secured by inserting locking pin.

Trim and rear spoiler, assembly overview

Note. The following list refers to (Схема №27).

  1. Bumper cover Can be replaced individually Remove bumper. Remove clips -5- from upperside. See «CLIP FOR BUMPER COVER»(ref-196883-S40657312212006060600000) . Remove hex bolts -9- Disengage locking mechanisms on cover and remove bumper cover.
  2. Bumper carrier Removing: Remove bumper. Unclip expanding clip -5- and remove bumper carrier from cover and spoiler.
  3. Center trim To avoid damage from scratches, first remove left and right trim Remove Phillips-head screws -10- on both ends of trim. Press locking lugs of retaining clamp together using pliers and slide trim out of bumper cover.
  4. Left trim Remove and install as done for front trim
  5. Expanding clip Qty: 18 Unclipping. See «CLIP FOR BUMPER COVER»(ref-196883-S40657312212006060600000) .
  6. Rear spoiler Can be replaced individually Remove bumper. Remove hex bolts -9- Remove clips -5- from underside. See «CLIP FOR BUMPER COVER»(ref-196883-S40657312212006060600000) . Disengage locking mechanisms on cover and remove spoiler.
  7. Torx bolts 1 Nm
  8. Ultrasound sensor Remove bumper. Disconnect electric harness connector -7- and remove bolt -7-. Press locking mechanisms slightly apart and remove sensor.
  9. Hex bolt 21 Nm
  10. Phillips-head screw 1 Nm
  1. To remove, pull out locking pin -2- as shown.
  2. Remove clip -2- from bumper cover.
  3. To install, clip is pressed into bumper and secured by inserting locking pin.

Note. The following list refers to (Схема №29).

  1. Bracket
  2. Guide Removing and installing. See «GUIDE, REMOVING AND INSTALLING»(ref-196883-S01658237512006060600000) .
  3. Bumper cover Slide bumper cover into guide -2- and bracket -1- as shown in illustration. Bumper cover must be guided into both guide -2- and bracket -1-. Tighten machine screw -5- to 65 Nm.
  4. Rear spoiler Can be replaced individually
  5. Machine screw 65 Nm

More articles — Bumper