Home/Volvo/V70/Volvo V70 II facelift (2004-2007)/Repair manual/Gearbox, Input/output Speed Sensor - Removal & Installation/Joining cables

Contents

Wiring diagrams Section: Gearbox, Input/output Speed Sensor - Removal & Installation

Gearbox, removing (Preparatory work)

Disconnecting the battery lead

Gearbox, removing (AW50/51 AWD; AW55-50/51SN; 2003-2007)

Gearbox, removing (M56; 2001-2007)

Gearbox, removing

Removing the hose

Measuring the position of the tie rod in the steering gear

Exposing the steering shaft joint

Removing the cap for the drive shaft support bearing

Installing the gearbox (AW50/51 AWD; B5234T3, AW55-50/51SN; 2001-2004)

Installing the angle gear

Installing the collision protection system over the steering gear

Installing the water hose

Installing the battery cable

Check

Installing the gearbox (AW50/51 AWD; AW55-50/51SN; 2001)

Installing the gearbox

Lifting the engine/gearbox

Installing the rear engine mounting

Installing the lower oil pipe to the gearbox

Installing the left-hand drive shaft to the gearbox and the wheel spindle

Fitting the subframe to the body

Installing the right-hand drive shaft to the gearbox, wheel spindle and link arm

Installing the steering wheel shaft joint

Installing the crossmembers

Installing the cable conduit

Removing the lifting beam

Fitting the remaining screws to the gearbox/starter motor

Installing the gear selector cables and oil line

Installing service clips

Installing engine compartment components

Installing the collision protection system over the steering gear (right-hand drive cars)

Lifting the engine and gearbox to the horizontal position

Installing the subframe on the bodywork

Installing the sealing ring for the CV joint housing

Installing the left drive shaft on the gearbox, stub axle and control arm

Installing the screws for the front engine pad

Installing the right drive shaft on the gearbox, stub axle and control arm

Installing new lock nuts on the steering gear

Lowering the car and removing the lifting beam and lifting tools from the engine

Installing the coolant hose

Installing the gearbox (TCM-002E, AW55-50/51SN; AW50/51 AWD; AW55-50/51SN; 2001-2007)

Fitting the sub-frame to the body

Installing the service clips

Installing the gearbox (B5254T4, TF-80SC AWD; 2006-2007)

Installing the left drive shaft on the transmission and the wheel spindle

Software

Jacking points, body

Installing the charge air pipe (only applies to 6-cylinder turbocharged engines)

Gear-shift position sensor, checking/adjusting

Gear-shift position sensor, checking/adjusting (AW50/51 AWD; AW55-50/51SN; 2001-2007)

Installing the gear selector cable

Input speed sensor/output speed sensor, replacing

Preparations

Installing the sensor

Installing the air cleaner (ACL) housing

Input speed sensor/output speed sensor, replacing (AW50/51 AWD; AW55-50/51SN; 2003-2007)

Information about the CAN network, structure and function

Joining cables

Disconnect the battery

Treat the cable terminal surfaces

Installing wheels (B5234T3; B5244S; B5244T3; 2001-2007)

All sections

Joining cables Volvo V70 II facelift

Gearbox, Input/output Speed Sensor - Removal & Installation 5 illustrations ~112 words

Joining cables

Special tools 951 2620 Stripping tool (for wiring) Tool number: 951 2620 Tool description: Stripping tool (for wiring) Tool boards: 39 951 2785 Crimping tool (included in 9512669) Tool number: 951 2785 Tool description: Crimping tool (included in 9512669) Tool boards: 39 951 2850 Hot air gun (110 V US) Tool number: 951 2850 Tool description: Hot air gun (110 V US) Tool boards: 951 2851 Hot-air gun (220V UK) Tool number: 951 2851 Tool description: Hot-air gun (220V UK) Tool boards: 08 951 2777 Hot-air gun Tool number: 951 2777 Tool description: Hot-air gun Tool boards: 08

Scheme 1736

Scheme 1736: Joining cables

Scheme 1736: Joining cables

Scheme 1737

Scheme 1737

Scheme 1737

Scheme 1738

Scheme 1738

Scheme 1738

Scheme 1739

Scheme 1739

Scheme 1739

Scheme 1740

Scheme 1740

Scheme 1740