Home/Volvo/S80/Volvo S80 I рестайлинг (2003-2006)/Repair manual/Control Modules - Design and Function - 3 of 3/Battery voltage, value

Contents

Section: Control Modules - Design and Function - 3 of 3

Reading off input and output signals

Activating components and functions

Reading off static data

Downloading software and replacing the control module

Alarm

Locks

Rear windshield wiper/washers

Signals

Central locking

Back-up lamp

Brake light

Reading off the parameter values

Explanation

Battery voltage, value

Distance, value

Passenger compartment temperature, value

Outside temperature, value

Engine running, status

Time, value

Battery voltage

Rear seat entertainment system

Downloading software

Preparations

Verification

Downloading

Confirmation

Completion

Ordering software products

Software products

Re-downloading

Upgrading

Total upgrading CAN/MOST

Individual configuration

The Volvo central database

Clutch lock function

Reading off the control module identity

Software downloading

Controlling functions and menu selection using the steering wheel buttons

Controlling the headlamps and turn signal lamps

Horn

Windshield wiper and washer functions

Electrical function

Front airbags

SRS indication

Activating the collision protection system

Activation levels for the collision protection system

Activating the side impact protection system

Fault indication

Reading off the parameters

ID number storage for occupant weight sensor (OWS)

The occupant weight sensor (OWS) system

Side impact sensor

Side impact air bags

Inflatable curtains

Seat belt buckle

Deploying airbags / seat belt tensioners

Deployment levels for airbags and seat belt tensioners (1999-2000)

Deployment levels for airbags and seat belt tensioners (2001-)

Deployment of side impact protection (SIPS) bags

Data read-out

SRS (supplemental restraint system)

Activating components

Continuously Controlled Chassis Concept (Four-C)

Changing the driving mode (R line)

Changing the driving mode (non R line)

Prioritizing

Two types of message

Compatibility

Configuration

Electrical faults

No communication from the control module

Faulty communication

Advantages of a network

High and low speed sides on the network

Transfer speeds

Terminating resistor

Cables, CAN H and CAN L

Controller area network (CAN) message

Quality factor

Display

Remote control

GPS navigation

RTI (road traffic information)

Differential

Power flow

Towing

Controlling the shift solenoids when shifting

Shifting program

Other modes

Park / neutral position (PNP) function

Adaptation data

Emergency mode in the event of a fault

Reading input and output signals

Activation of components

Gear-shift position sensor position

Gear-shift position sensor signal A

Gear-shift position sensor signal B

Gear-shift position sensor signal C

Gear-shift position sensor signal PA

Quick shift function from the gear selector module

Quick shift shifting from gear selector module

Quick shift status according to transmission control module

Winter mode status

Current gear (according to gear ratio)

New gear (according to solenoids)

Shift solenoid status S1

Shift solenoid status S2

Lock-up solenoid SL status

Lock-up pressure switch

Stop (brake) lamp switch

Kickdown

Engine speed (RPM)

Transmission speed sensor, input speed

TCM speed sensor, calculated speed

Vehicle speed ABS

Throttle, position

Calculated battery voltage

Oil temperature sensor signal

Oil temperature

Line pressure solenoid STH amperage

Line pressure solenoid STH control

Lock-up solenoid SL, amperage

Engine control module (ECM) engine coolant temperature (ECT)

Text transmitted to the driver information module

Shifting using Geartronic

Shift-lock

Ignition switch interlock

Reading off and programming data

Programming remote controls

Tire pressure monitoring system (TPMS)

Automatic rear view mirror anti-dazzle

Siren control module (SCM)

Sun roof

Rain sensor module (RSM)

Interior roof lighting

Rear view mirror

Compass

All sections

Battery voltage, value Volvo S80 I рестайлинг

Control Modules - Design and Function - 3 of 3

Battery voltage, value

Measurement range: 0-12 V.

Normal value when the generator (GEN) is charging: 13.0-14.5 V.

The value is the voltage from the central electronic module (CEM).