TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) |
|---|
| Caliper Guide Pin Bolts | 25 (34) |
| Finger-Tighten Nuts | 63 (85) |
| Front Caliper Mounting Bolts | (1) 74 (100) |
| Master Cylinder Mounting Bolts | 22 (30) |
| Brake Shoes Mounting Bolts | 43 (58) |
| Rear Caliper Mounting Bolts | (1) 43 (58) |
| Wheel Lug Nuts | 63 (86) |
| INCH Lbs. (N.m) |
| Rotor Retaining Stud | 72 (8) |
| (1) Manufacturer recommends using new fasteners if originals are loosened or removed. |
| (1) | Manufacturer recommends using new fasteners if originals are loosened or removed. |
| Application | In. (mm) |
|---|
| Disc Diameter |
| Front |
| Solid (Type 1) | 11.02 (280) |
| Vented |
| Type 2 | 10.33 (262) |
| Type 3 | 11.30 (287) |
| Type 4 | 11.02 (280) |
| Rear |
| Version 1 (1) | 11.06 (281) |
| Version 2 (2) | 10.43 (265) |
| Lateral Runout (Maximum) |
| Front | .002 (.06) |
| Rear |
| Version 1 (1) (3) | .003 (.08) |
| Version 2 (2) (3) | .002 (.06) |
| Original Thickness |
| Front |
| Solid (Type 1) | .551 (14) |
| Vented |
| Type 2 | .866 (22) |
| Type 3 | .866 (22) |
| Type 4 | 1.023 (26) |
| Rear |
| Version 1 (1) | .377 (9.6) |
| Version 2 (2) | .394 (10) |
| Minimum Refinish Thickness | (4) |
| Discard Thickness |
| Front |
| Solid | .433 (11) |
| Vented |
| Type 2 | .787 (20) |
| Type 3 | .787 (20) |
| Type 4 | .905 (23) |
| Rear |
| Version 1 (1) | .330 (8.4) |
| Version 2 (2) | .315 (8) |
| Parking Brake Drum (Inside Rotor) |
| Maximum Diameter | 6.32 (160.45) |
| Maximum Radial Runout | .006 (.15) |
| Maximum Ovality | .008 (.2) |
| Master Cylinder Diameters |
| Primary (Without ABS) |
| Early Version | .867 (22.3) |
| Later Version | .937 (23.8) |
| Primary (With ABS) |
| Early Version | .874 (22.2) |
| Later Version | .937 (23.8) |
| Secondary (Without ABS) |
| Early Version | .620 (15.75) |
| Later Version | .662 (16.84) |
| Secondary (With ABS) |
| Early Version | .749 (19.05) |
| Later Version | .812 (20.64) |
| (1) Live rear axle. (2) Multilink suspension. (3) As measured with brake disc mounted on vehicle. (4) Always use minimum thickness specification stamped on rotors. |
| (3) | As measured with brake disc mounted on vehicle. |
| (4) | Always use minimum thickness specification stamped on rotors. |
DISC BRAKE SPECIFICATIONS
