| A/C Compressor Bolt | 13 (18) |
| A/C Compressor Mounting Bracket Bolt | 35 (47) |
| Air Intake Chamber Bolt/Nut | 13 (18) |
| Air Intake Chamber Support Brace Bolt | 30 (41) |
| Camshaft Bearing Cap Bolt (1) | 12 (16) |
| Camshaft Sprocket Retaining Bolt | 81 (110) |
| Center Bearing Support Bolt |
| Tacoma 2WD & T100 2WD | 27 (37) |
| Connecting Rod Nut |
| Step 1 | 18 (24) |
| Step 2 | Additional 90 Degrees |
| Crankshaft Pulley Bolt | 184 (250) |
| Crossover Pipe Nut | 33 (45) |
| Cylinder Head Bolt |
| 12-Point Bolt (2) |
| Step 1 | 25 (34) |
| Step 2 | Additional 90 Degrees |
| Step 3 | Additional 90 Degrees |
| Recessed Bolt | 13 (18) |
| Drive Shaft Flange-To-Front Differential Flange Bolt/Nut | 54 (73) |
| Drive Shaft Flange-To-Rear Differential Flange Bolt/Nut | 54 (73) |
| Drive Shaft Flange-To-Transfer Case Flange Bolt/Nut | 54 (73) |
| EGR Pipe Nut |
| Nut At Clamp On EGR Pipe | (3) |
| Nut At End Of EGR Pipe | 14 (19) |
| Engine Mount-To-Frame Bolt/Nut | 28 (38) |
| Exhaust Manifold Nut | 30 (41) |
| Flywheel/Drive Plate Bolt |
| A/T | 61 (83) |
| M/T | 63 (85) |
| Front Axle Shaft Flange-To-Side Gear Shaft Flange Nut |
| T100 4WD | 61 (83) |
| Front Crossmember Bolt/Nut |
| T100 4WD | 93 (126) |
| Front Differential Mount Bolt |
| Tacoma 4WD & 4Runner 4WD | 101 (137) |
| T100 4WD | 123 (167) |
| Front Differential Rear Mount Bolt/Nut |
| T100 4WD | 108 (146) |
| Front Differential Rear Mount Nut |
| Tacoma 4WD & 4Runner 4WD | 64 (87) |
| Front Exhaust Pipe-To-Catalytic Converter Bolt |
| Tacoma 2WD & T100 2WD | 35 (47) |
| Front Exhaust Pipe Support Bracket Bolt | 33 (45) |
| Front Exhaust Pipe-To-Crossover Pipe Nut | 46 (62) |
| Front Exhaust Pipe-To-Rear Exhaust Bolt |
| 4Runner | 35 (47) |
| Fuel Crossover Pipe Union Bolt | 25 (34) |
| Fuel Inlet Pipe-To-Fuel Rail Union Bolt | 25 (34) |
| Generator Mounting Bracket Bolt | 14 (19) |
| Intake Air Connector Bolt/Nut | 13 (18) |
| Intake Manifold Bolt/Nut | 13 (18) |
| Intake Manifold Support Brace Bolt | 13 (18) |
| Knock Sensor | 29 (39) |
| Main Bearing Cap Bolt (4) |
| Step 1 | 45 (61) |
| Step 2 | Additional 90 Degrees |
| No. 1 Idler Pulley Bolt | 26 (35) |
| No. 2 Idler Pulley Bolt | 30 (41) |
| Oil Cooler Union Bolt | 43 (58) |
| Oil Pump Bolt | (5) |
| Power Steering Pump Bolt/Nut | 32 (43) |
| Power Steering Pump Mounting Bracket Bolt | 14 (19) |
| Rear Camshaft Bearing Cap Bolt | 12 (16) |
| Rear Transmission Mount Bracket-To-Crossmember Bolt |
| Tacoma 2WD, T100 2WD & 4Runner 2WD | 43 (58) |
| Rear Transmission Mount Bracket-To-Transmission Mount Bolt |
| Tacoma 2WD, T100 2WD & 4Runner 2WD | 13 (18) |
| Spark Plug | 13 (18) |
| Stabilizer Bar Mount Bracket-To-Frame Bolt |
| T100 2WD | 22 (30) |
| Starter Bolt | 29 (39) |
| Thermostat Housing Nut | 15 (20) |
| Timing Belt Tensioner Bolt | 20 (27) |
| Torque Converter Bolt | 30 (41) |
| Transmission-To-Clutch Housing Bolt |
| M/T | 53 (72) |
| Transmission-To-Cylinder Block Bolt |
| A/T | 53 (72) |
| Water Pump Bolt | 15 (20) |
| INCH Lbs. (N.m) |
| Camshaft Position Sensor Bolt | 71 (8.0) |
| Clutch Release Cylinder Bolt |
| Tacoma 2WD & T100 2WD | 106 (12.0) |
| Crankshaft Rear Oil Seal Housing Bolt | 71 (8.0) |
| EGR Pipe-To-Cylinder Head Nut | 71 (8.0) |
| Exhaust Manifold Heat Insulator Nut | 71 (8.0) |
| Fan Clutch-To-Fan Bracket Nut | 48 (5.4) |
| Fuel Inlet Pipe-To-Intake Manifold Clamp Bolt | 71 (8.0) |
| Fuel Pressure Regulator Bolt | 71 (8.0) |
| Fuel Rail-To-Intake Manifold Bolt | 115 (13.0) |
| Ignition Coil-To-Valve Cover Bolt | 69 (7.8) |
| Lower Timing Belt Cover Bolt | 80 (9.0) |
| Oil Pan Bolt/Nut | 67 (7.6) |
| Oil Pump Body Cover Screw | 89 (10.1) |
| Oil Pump Pick-Up Tube Bolt/Nut | 66 (7.5) |
| Rear Plate-To-Cylinder Head Bolt/Nut | 71 (8.0) |
| Rear Timing Belt Cover Bolt | 80 (9.0) |
| Stabilizer Bar-To-Lower Control Arm Bolt |
| T100 2WD | 115 (13.0) |
| Upper Timing Belt Cover Bolt | 80 (9.0) |
| Valve Cover Bolt | 53 (6.0) |
| (1) Tighten bolts to specification in sequence. (Схема №31) (2) Tighten bolts to specification in sequence. (Схема №12) (3) Tighten nut to 71 INCH lbs. (8.0 N.m). (4) Tighten bolts to specification in sequence. (Схема №39) (5) Tighten small bolt at outside left corner of oil pump to 15 ft. lbs. (20 N.m) and all other large bolts to 31 ft. lbs. (42 N.m). |
