Tightening Torque Specifications
| Fastening part | Tightening torque | Note | ||
|---|---|---|---|---|
| N.m | Kgf-m | Lb-ft | ||
| Camshaft housing bolt | 11 | 1.1 | 8.0 | |
| Air cleaner outlet hose clamp | 3 | 0.3 | 2.5 | |
| IMT valve actuator bolt | 6 | 0.6 | 4.5 | |
| Cylinder head cover nut | Tighten 11 N.m (1.1 kgf-m, 8.0 lb-ft) by the specified procedure | |||
| Suspension frame mounting bolt | 150 | 15.0 | 108.5 | |
| Front lower cross member bolt | 55 | 5.5 | 40.0 | |
| Starting motor terminal nut | 11 | 1.1 | 8.0 | |
| Generator terminal nut | 5 | 0.5 | 4.0 | |
| Battery ground bolt | 25 | 2.5 | 18.0 | |
| Ground terminal bolt | 11 | 1.1 | 8.0 | |
| Timing chain cover bolt and nut | 11 | 1.1 | 8.0 | |
| Idler pulley nut | 42 | 4.2 | 30.5 | |
| Generator belt tensioner bolt | 25 | 2.5 | 18.5 | |
| Crankshaft pulley bolt | 150 | 15.0 | 108.5 | |
| Camshaft timing sprocket bolt | 80 | 8.0 | 57.5 | |
| Timing chain tensioner adjuster No.2 bolt | 11 | 1.1 | 8.0 | |
| Timing chain tensioner adjuster No.2 nut | 45 | 4.5 | 33.0 | |
| Timing chain tensioner nut | 25 | 2.5 | 18.0 | |
| Timing chain tensioner adjuster No.1 bolt | 11 | 1.1 | 8.0 | |
| Timing chain guide No.1 bolt | 9 | 0.9 | 6.5 | |
| Camshaft housing bolt | Tighten 11 N.m (1.1 kgf-m, 8.0 lb-ft) by the specified procedure | |||
| Cylinder head bolt (M10) | Tighten 52 N.m (5.2 kgf-m, 38.0 lb-ft), 82 N.m (8.2 kgf-m, 59.5 lb-ft), 0 N.m (0 kgf-m, 0 lb-ft), 52 N.m (5.2 kgf-m, 38.0 lb-ft) and 103 N.m (10.3 kgf-m, 74.5 lb-ft) by the specified procedure | |||
| Cylinder head bolt (M6) | 11 | 1.1 | 8.0 | |
| Connecting rod bolt | Tighten 15 N.m (1.5 kgf-m, 11.0 lb-ft), 45° and 45° by the specified procedure | |||
| Cylinder block heater mounting bolt | 11 | 1.1 | 8.0 | |
| Crankcase bolt with 10 mm thread diameter ((1) - (10)) | Tighten 40 N.m (4.0 kgf-m, 29.0 lb-ft), 0 N.m (0 kgf-m, 0 lb-ft), 40 N.m (4.0 kgf-m, 29.0 lb-ft), 58 N.m (5.8 kgf-m, 42.0 lb-ft) by the specified procedure | |||
| Crankcase bolt with 8 mm thread diameter ((11) - (22)) | Tighten 26 N.m (2.6 kgf-m, 19.0 lb-ft) by the specified procedure | |||
| CKP sensor bolt | 11 | 1.1 | 8.0 | |
| Flywheel or drive plate bolt | 70 | 7.0 | 51.0 | |
| Engine front mounting bracket bolt | 55 | 5.5 | 40.0 | |
TIGHTENING TORQUE SPECIFICATIONS
Note. The specified tightening torque is also described in the following: AIR CLEANER COMPONENTS , ELECTRIC THROTTLE BODY AND INTAKE MANIFOLD COMPONENTS , CYLINDER HEAD COVER COMPONENTS , ENGINE MOUNTINGS COMPONENTS , TIMING CHAIN COVER COMPONENTS , 2nd TIMING CHAIN AND CHAIN TENSIONER COMPONENTS , 1st TIMING CHAIN AND CHAIN TENSIONER COMPONENTS , CAMSHAFTS, TAPPET AND SHIM COMPONENTS , VALVES AND CYLINDER HEAD COMPONENTS , PISTONS, PISTON RINGS, CONNECTING RODS AND CYLINDERS COMPONENTS and MAIN BEARINGS, CRANKSHAFT AND CYLINDER BLOCK COMPONENTS
Reference
For the tightening torque of fastener not specified in this article, refer to FASTENERS INFORMATION .