| CNG Fuel Inlet Fitting-To-Tank Valve | 18 (24) |
| CNG Fuel Outlet Fitting-To-Tank Valve | 20 (27) |
| CNG Fuel Tank Pressure Sensor | 20 (27) |
| CNG Fuel Tank Strap Nut | 35 (48) |
| CNG Tank Vent Fitting Between HPL Fill Line Port & Female Vent Hose Fitting | 35 (48) |
| Fill Line | 30 (41) |
| Fill Line-To-Union Fitting | 27 (37) |
| Fill Valve Retaining Nut | 30 (41) |
| Fuel Tank Retaining Strap Bolt | 26 (35) |
| FTP Sensor | 20 (27) |
| FTP Sensor Port Fitting | 27 (37) |
| FTP Sensor Port Fitting CAP | 35 (48) |
| HO2S 1 | 22 (30) |
| HO2S 2 | 30 (41) |
| HPL Fill Line Fitting | 27 (37) |
| HPL Solenoid | (1) 225 (305) |
| HPL Pressure Relief Device Line | 27 (37) |
| HPL-To-HPR Fitting | 18 (24) |
| HPR Mounting Nut | 41 (55) |
| Ignition Control Module Retaining Screw | 13 (1.5) |
| Ignition Control Module Cover Bolt | 18 (10) |
| Knock Sensor Retaining Bolt | 18 (24) |
| Low Pressure Lock-Off Mounting Bolt | 9 (12) |
| LPL Fuel Inlet Elbow Fitting | 18 (24) |
| LPR/LPL-To-Transaxle Mounting Studs | 20 (28) |
| (2) Outlet Fitting Cap | 27 (37) |
| Pressure Relief Device-To-HPL | 27 (37) |
| Spare Tire Bracket Bolt | 20 (27) |
| Starter Bolt | 30 (41) |
| CNG Tank Strap Nut | 35 (47) |
| INCH Lbs. (N.m) |
| Accelerator Cable Bracket Nut | 89 (10) |
| Air Cleaner Duct-To-Resonator Clamp | 44 (5) |
| Air Cleaner Intake Duct Clamp | 44 (5) |
| Battery Cable Clamp Bolt | 133 (15) |
| CNG Fuel Tank Cover Bolts | 54 (6) |
| CNG Low Pressure Lock-Off Regulator Bolt | 108 (12) |
| CNG Low Pressure Lock-Off Solenoid Bracket Nut | 108 (12) |
| Crankshaft Position Sensor Bolt/Nut | 71 (8) |
| Cruise Control Cable Bracket | 89 (10) |
| Engine Coolant Temperature Sensor | 89 (10) |
| EVAP Canister Purge Valve Bracket Nut | 71 (8) |
| EVAP Canister Retainer Bolt | 89 (10) |
| Exhaust Shield Bolt | 18 (2) |
| Exhaust Shield Nut | 9 (1) |
| Fuel Hose Retainer Hold-Down Nut | 106 (12) |
| Fuel Injector Control Module Mounting Bolts | 106 (12) |
| Fuel Line Fitting-To-Fuel Rail | 89 (10) |
| Fuel Pressure Regulator Bolt | 89 (10) |
| Fuel Rail Attaching Bolt | 89 (10) |
| Fuel Tank Pressure Sensor | (1) |
| Hose Clamps | 18 (2) |
| HPL Connector Stand-Offs | 106 (12) |
| Idle Air Control Valve Screw | 27 (3) |
| Ignition Coil Housing Retaining Bolt | 89 (10) |
| Ignition Control Module-To-Housing Bolt | 89 (10) |
| LPR & LPL Mounting Bolt | 108 (12) |
| (2) Manual Vent Tool | 106 (12) |
| Throttle Body Retaining Bolt | 89 (10) |
| Throttle Position Sensor Screw | 18 (2) |
| Union-To-HPL Fill Line | 27 (37) |
| Upper Radiator Mounting Brackets Bolts | 89 (10) |
| Hood Latch Support Bolts | 80 (9) |
| Vent Boot Hose Clamp | 18 (2) |
| (1) A nominal torque at zero degrees. You must compensate for the torque wrench and the HPL crowfoot offset. To obtain your dial reading, multiply torque wrench length in inches by 305. 18 inch torque wrench example: 18 X 305 = 5490. Add 3 to the length of torque wrench. 18 inch torque wrench example: 18 + 3 = 21. Divide the first value obtained by the second value obtained. The result indicates the amount of torque your wrench should tighten the HPL to. 18 inch torque wrench example: 5490 divided by 21 = 261.4. For an 18 inch long torque wrench tighten the HPL to 193 ft. lbs. (261.4 N.m). (2) From CNG Take Venting Kit (J 42435) |
