Home/Peugeot/307/Peugeot 307 3C (2001-2005)/Repair manual/Power unit/Re-assembling: engine — variant 8
Contents Wiring diagrams Section: Power unit All sections

Re-assembling: engine — variant 8 Peugeot 307 3C

Power unit ~303 words

Re-assembling

Refit

  • The flywheel (1)
  • Pre-coated bolts (2) (LOCTITE FRENETANCH)

Insert the flywheel stop [4]

Tighten (in the order shown): engine flywheel fixing bolt (2)

Centre on the flywheel (using tool [22])

  • The clutch plate (3)
  • The clutch mechanism (4)

Tighten the bolts (5)

Remove the tool [22]

Refit: the cap from the camshaft dephaser (6) (inlet)

Fit the cap

Refit

  • The cylinder head covers (7)
  • The timing housings (8)

WarningTighten in the sequence indicated

Refit

  • The exhaust manifold seal (9)
  • The exhaust manifold (10)
  • The 10 nuts (11)

Fit the new rubber seals to the inlet manifold

Refit: the inlet manifold (12)

Tighten

  • The 5 nuts (13)
  • The 2 bolts (14)

Refit

  • The sparking plugs
  • The lifting plates (15)
  • The air pressure sensor (16)
  • The camshaft position sensor (17)

WarningFit new seals on the water outlet housing and the coolant temperature sensor

Refit

  • The piloting electrovalve (18)
  • The thermostat (19)

Refit the coil pack unit (20)

Refit the oil gauge guide tube (21) (sealing on engine block with RECTIJOINT adhesive paste)

Refit

  • The oxygen sensor (23)
  • The heat shield (22)

Refit

  • The oil filter bracket (24) (tighten the bolts (26))
  • The oil pressure switch (25)
  • According to equipment: The electric oil gauge (27)

Refit

  • The centralising pins (28) (compressor bracket - alternator mounting)
  • The alternator bracket (29)
  • The compressor bracket (30)

Tighten the bolts (31)

Refit

  • The roller tensioner (33)
  • The ancillary drive pulley (35)

Tighten

  • The (32) bolt
  • The bolts (34)
  • Fixing bolt in the ancillaries drive pulley

Refit

  • The alternator (36)
  • The air-conditioning compressor (37)

Tighten

  • The 4 alternator fixing bolts
  • The 4 fixing bolts on the air conditioning compressor

Refit the intermediate engine support (38)

Tighten: lower engine mounting (39)

Refit the ancillary belt

Refit the ancillary belt

Refit the ancillary belt

Tightening torques

referencedesignationdaNm
(2)engine flywheel fixing bolt6.7
(5)clutch cover fastener2.0
(6)camshaft dephaser cap3.2
-fixing of cylinder head cover0.9
-timing cover fixing0.8
(11)exhaust manifold fastenings0.8
(13 - 14)inlet manifold mountings0.8
-sparking plugs2.25
-lifting bracket3.0
-pressure sensor0.8
-camshaft position sensor0.2
(18)control electrovalve0.8
-fixing of water outlet housing0.8
-fixing: compact coil block0.8
-the bolt which secures the dipstick tube to the cylinder head0.7
(23)oxygen sensor4.7
-heat shield fixing0.8
(25)oil pressure switch2.0
(26)fixing of the oil filter mounting1.0
(27)electric oil gauge3.2
(31)fixing securing support (alternator - compressor)2.5
(32)timing roller tensioner fixing2.5
(34)timing roller tensioner fixing5.4
-ancillaries pulley fastening0.8
-alternator mounting bolts4.9
-compressor fastener2.5
(39)lower engine mounting4.5