Home ReviewsRefund
Home/Nissan/Titan/Nissan Titan I (2003-2006)/Repair manual/Power Locks & Anti-Theft Systems/Inputs
Contents Wiring diagrams Section: Power Locks & Anti-Theft Systems All sections

Inputs Nissan Titan I

Power Locks & Anti-Theft Systems ~554 words

Inputs

Power is supplied at all times

  1. To BCM terminal 70
  2. Through 50A fusible link (letter f , located in the fuse and fusible link box).
  3. To BCM terminal 57
  4. Through 15A fuse [No. 22, located in the fuse block (J/B)].

When the key switch and key lock solenoid is ON (inserted), power is supplied

  1. To BCM terminal 37
  2. Through key switch and key lock solenoid terminals 3 and 4
  3. Through 10A fuse [No. 19, located in the fuse block (J/B)].

When the ignition switch is ACC or ON, power is supplied

  1. To BCM terminal 11
  2. Through 10A fuse [No. 4, located in the fuse block (J/B)].

When the ignition switch is ON or START, power is supplied

  1. To BCM terminal 38
  2. Through 10A fuse (No. 59, located in the fuse and relay box).

BCM is connected to main power window and door lock/unlock switch and power window and door lock/unlock switch RH through a serial link.

When the front door switch LH is ON (door is open), ground is supplied

  1. To BCM terminal 47
  2. Through front door switch LH terminals 2 and 3
  3. through grounds B7 and B19.

When the rear door switch upper LH is ON (door is open), ground is supplied

  1. To BCM terminal 47
  2. Through rear door switch upper LH terminals 1 and 2
  3. Through grounds B7 and B19.

When the rear door switch lower LH is ON (door is open), ground is supplied

  1. To BCM terminal 47
  2. Through rear door switch lower LH terminals 1 and 2
  3. Through grounds B7 and B19.

When the front door switch RH is ON (door is open), ground is supplied

  1. To BCM terminal 12
  2. Through front door switch RH terminals 2 and 3
  3. Through grounds B117 and B132.

When the rear door switch upper RH is ON (door is open), ground is supplied

  1. To BCM terminal 12
  2. Through rear door switch upper RH terminals 1 and 2
  3. Through grounds B117 and B132.

When the rear door switch lower RH is ON (door is open), ground is supplied

  1. To BCM terminal 12
  2. Through rear door switch lower RH terminals 1 and 2
  3. Through grounds B117 and B132.

BCM is connected to main power window and door lock/unlock switch and power window and door lock/unlock switch RH through a serial link.

When the front door switch LH is ON (door is open), ground is supplied

  1. To BCM terminal 47
  2. Through front door switch LH terminal 2
  3. Through front door switch LH case ground.

When the front door switch RH is ON (door is open), ground is supplied

  1. To BCM terminal 12
  2. Through front door switch RH terminal 2
  3. Through front door switch RH case ground.

When the rear door switch LH is ON (door is open), ground is supplied

  1. To BCM terminal 48
  2. Through rear door switch LH terminal 2
  3. Through rear door switch LH case ground.

When the rear door switch RH is ON (door is open), ground is supplied

  1. To BCM terminal 13
  2. Through rear door switch RH terminal 2
  3. Through rear door switch RH case ground.

Key fob signal is inputted to BCM from the remote keyless entry receiver. The remote keyless entry system controls operation of the

  1. power door lock
  2. interior lamp and step lamps
  3. panic alarm
  4. hazard and horn reminder
  5. keyless power window down (open)
  6. auto door lock operation