APPLICATION ITEM
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
| Diagnosis mode | Function description |
|---|---|
| ECU Identification | BCM part number is displayed. |
| Self-Diagnostic Result | Displays the diagnosis results judged by BCM. Refer to " DTC INDEX ". |
| Data Monitor | BCM input/output signals are displayed. |
| Active Test | The signals used to activate each device are forcibly supplied from BCM. |
| Work Support | Changes the setting for each system function. |
| Configuration | Read and save the vehicle specification. Write the vehicle specification when replacing BCM. |
| CAN Diag Support Monitor | Monitors the reception status of CAN communication viewed from BCM. |
DIAGNOSTIC TEST MODES CHART
SYSTEM APPLICATION
BCM can perform the following functions for each system.
Note. It can perform the diagnosis modes except the following for all sub system selection items.
| X: Applicable item | ||||
|---|---|---|---|---|
| System | CONSULT-III sub system selection item | Diagnosis mode | ||
| Work Support | Data Monitor | Active Test | ||
| Door lock | DOOR LOCK | X | X | X |
| Rear window defogger | REAR DEFOGGER | X | X | |
| Warning chime | BUZZER | X | X | |
| Interior room lamp control | INT LAMP | X | X | X |
| Remote keyless entry system | MULTI REMOTE ENT | X | X | X |
| Exterior lamp | HEAD LAMP | X | X | X |
| Wiper and washer | WIPER | X | X | X |
| Turn signal and hazard warning lamps | FLASHER | X | X | |
| Auto air conditioning system Manual air conditioning system | AIR CONDITONER | X | ||
| Intelligent Key system | INTELLIGENT KEY | X | ||
| Combination switch | COMB SW | X | ||
| Body control system | BCM | X | ||
| Immobilizer | IMMU | X | X | |
| Interior room lamp battery saver | BATTERY SAVER | X | X | X |
| Back door open | TRUNK | X | X | |
| Vehicle security system | THEFT ALM | X | X | X |
| RAP system | RETAINED PWR | X | X | X |
| Signal buffer system | SIGNAL BUFFER | X | X | |
| FUEL LID (1) | ||||
| TPMS | TPMS (AIR PRESSURE MONITOR) | X | X | X |
| Panic alarm system | PANIC ALARM | X | ||
| (1) This item is displayed, but is not function. | ||||
| (1) | This item is displayed, but is not function. |
SUB SYSTEM SELECTION ITEMS CHART
CONSULT-III performs the following functions via CAN communication with BCM.
| Diagnosis mode | Function Description |
|---|---|
| DATA MONITOR | The BCM input/output signals are displayed. |
| ACTIVE TEST | The signals used to activate each device are forcibly supplied from BCM. |
CONSULT-III FUNCTION CHART (BCM - IMMU)
CONSULT-III performs the following functions via CAN communication with BCM.
| Diagnosis mode | Function Description |
|---|---|
| DATA MONITOR | The BCM input/output signals are displayed |
| ACTIVE TEST | The signals used to activate each device are forcibly supplied from Intelligent Key unit |
CONSULT-III FUNCTION CHART (BCM - TRUNK)
CONSULT-III performs the following functions via CAN communication with BCM.
| Diagnosis mode | Function Description |
|---|---|
| WORK SUPPORT | Changes the setting for each system function. |
| DATA MONITOR | The BCM input/output signals are displayed. |
| ACTIVE TEST | The signals used to activate each device are forcibly supplied from BCM. |
CONSULT-III FUNCTION CHART (BCM - THEFT ALM)
CONSULT-III performs the following functions via CAN communication with BCM.
| Diagnosis mode | Function Description |
|---|---|
| ACTIVE TEST | The signals used to activate each device are forcibly supplied from BCM |
CONSULT-III FUNCTION CHART (BCM - PANIC ALARM)