APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
| Diagnosis mode | Function Description |
|---|
| Work Support | Changes the setting for each system function. |
| Self Diagnostic Result | Displays the diagnosis results judged by BCM. |
| CAN Diag Support | Monitor Monitors the reception status of CAN communication viewed from BCM. |
| Data Monitor | The BCM input/output signals are displayed. |
| Active Test | The signals used to activate each device are forcibly supplied from BCM. |
| Ecu Identification | The BCM part number is displayed. |
| Configuration | Read and save the vehicle specification. Write the vehicle specification when replacing BCM. |
SYSTEM APPLICATION
BCM can perform the following functions for each system.
Note. It can perform the diagnosis modes except the following for all sub system selection items.
| System | Sub system selection item | Diagnosis mode |
|---|
| Work Support | Data Monitor | Active Test |
| Door lock | DOOR LOCK | (1) | (1) | (1) |
| Rear window defogger | REAR DEFOGGER | | (1) | (1) |
| Warning chime | BUZZER | | (1) | (1) |
| Interior room lamp timer | INT LAMP | (1) | (1) | (1) |
| Exterior lamp | HEAD LAMP | (1) | (1) | (1) |
| Wiper and washer | WIPER | (1) | (1) | (1) |
| Turn signal and hazard warning lamps | FLASHER | (1) | (1) | (1) |
| Air conditioning system | AIR CONDITONER | | (1) | (1) (2) |
| Intelligent Key system Engine start system | INTELLIGENT KEY | (1) | (1) | (1) |
| Combination switch | COMB SW | | (1) | |
| Body control system | BCM | | (1) | |
| NVIS - NATS | IMMU | (1) | (1) | (1) |
| Interior room lamp battery saver | BATTERY SAVER | (1) | (1) | (1) |
| Back door open | TRUNK | | (1) | |
| Theft warning alarm | THEFT ALM | (1) | (1) | (1) |
| RAP | RETAINED PWR | | (1) | |
| Signal buffer system | SIGNAL BUFFER | | (1) | (1) |
| TPMS | AIR PRESSURE MONITOR | (1) | (1) | (1) |
| (1) Applicable item NOTE: (2) For models with automatic A/C, this diagnosis mode is not used. |
| NOTE |
|---|
| (2) For models with automatic A/C, this diagnosis mode is not used. |
| (2) | For models with automatic A/C, this diagnosis mode is not used. |
CONSULT performs the following functions via CAN communication with BCM.
| Diagnosis mode | Function Description |
|---|
| Work Support | Changes the setting for each system function. |
| Self Diagnostic Result | Displays the diagnosis results judged by BCM. |
| CAN Diag Support Monitor | Monitors the reception status of CAN communication viewed from BCM. |
| Data Monitor | The BCM input/output signals are displayed. |
| Active Test | The signals used to activate each device are forcibly supplied from BCM. |
| Ecu Identification | The BCM part number is displayed. |
| Configuration | Read and save the vehicle specification. Write the vehicle specification when replacing BCM. |
BCM can perform the following functions for each system.
Note. It can perform the diagnosis modes except the following for all sub system selection items.
| System | Sub system selection item | Diagnosis mode |
|---|
| Work Support | Data Monitor | Active Test |
| Door lock | DOOR LOCK | (1) | (1) | (1) |
| Rear window defogger | REAR DEFOGGER | | (1) | (1) |
| Warning chime | BUZZER | | (1) | (1) |
| Interior room lamp control | INT LAMP | (1) | (1) | (1) |
| Remote keyless entry system | MULTI REMOTE ENT | (1) | (1) | (1) |
| Exterior lamp | HEAD LAMP | (1) | (1) | (1) |
| Wiper and washer | WIPER | (1) | (1) | (1) |
| Turn signal and hazard warning lamps | FLASHER | | (1) | (1) |
| Air conditioning system | AIR CONDITONER | | (1) | (1) |
| Combination switch | COMB SW | | (1) | |
| Body control system | BCM | (1) | | |
| NATS | IMMU | (1) | | (1) |
| Interior room lamp battery saver | BATTERY SAVER | (1) | (1) | (1) |
| Back door open | TRUNK | | (1) | |
| Theft warning alarm | THEFT ALM | (1) | (1) | (1) |
| RAP system | RETAINED PWR | | (1) | (1) |
| Signal buffer system | SIGNAL BUFFER | | (1) | (1) |
| Panic alarm | PANIC ALARM | | | (1) |
| TPMS | AIR PRESSURE MONITOR | (1) | (1) | (1) |
| (1) Applicable item |
CONSULT performs the following functions via CAN communication with IPDM E/R.
| Diagnosis mode | Description |
|---|
| Ecu Identification | Allows confirmation of IPDM E/R part number. |
| Self Diagnostic Result | Displays the diagnosis results judged by IPDM E/R. |
| Data Monitor | Displays the real-time input/output data from IPDM E/R input/output data. |
| Active Test | IPDM E/R can provide a drive signal to electronic components to check their operations. |
| CAN Diag Support Monitor | The results of transmit/receive diagnosis of CAN communication can be read. |
CONSULT performs the following functions via CAN communication with IPDM E/R.
| Diagnosis mode | Description |
|---|
| Ecu Identification | Allows confirmation of IPDM E/R part number. |
| Self Diagnostic Result | Displays the diagnosis results judged by IPDM E/R. |
| Data Monitor | Displays the real-time input/output data from IPDM E/R input/output data. |
| Active Test | IPDM E/R can provide a drive signal to electronic components to check their operations. |
| CAN Diag Support Monitor | The results of transmit/receive diagnosis of CAN communication can be read. |
