Home ReviewsRefund
Home/Mazda/Tribute/Mazda Tribute II (2007-2011)/Repair manual/Engine Mechanical - Hybrid: Removal & Installation/Installation
Contents Wiring diagrams Section: Engine Mechanical - Hybrid: Removal & Installation All sections

Installation Mazda Tribute II

Engine Mechanical - Hybrid: Removal & Installation 35 illustrations ~1364 words

Installation

All vehicles

Scheme 832

Scheme 832: Installation
Scheme 832: Installation

Scheme 833

Scheme 833
Scheme 833

Scheme 834

Scheme 834
Scheme 834

Scheme 835

Scheme 835
Scheme 835

Scheme 836

Scheme 836
Scheme 836

Scheme 837

Scheme 837
Scheme 837

Scheme 838

Scheme 838
Scheme 838

Scheme 839

Scheme 839
Scheme 839

Scheme 840

Scheme 840
Scheme 840

Scheme 841

Scheme 841
Scheme 841

Scheme 842

Scheme 842
Scheme 842

Scheme 843

Scheme 843
Scheme 843

Scheme 844

Scheme 844
Scheme 844

Scheme 845

Scheme 845
Scheme 845

Scheme 846

Scheme 846
Scheme 846

Scheme 847

Scheme 847
Scheme 847

Scheme 848

Scheme 848
Scheme 848

Scheme 849

Scheme 849
Scheme 849

Scheme 850

Scheme 850
Scheme 850

Scheme 851

Scheme 851
Scheme 851

Scheme 852

Scheme 852
Scheme 852
  1. Install the transaxle damper. Tighten to 29 N.m {2.9 kgf.m, 21 ft.lbf}. NOTE: Due to packaging requirements the correct bolt must be used at the damper locations. NOTE: The damper contains a clutch which is designed to slip briefly during vehicle operation. It is essential that no grease, oil or cleaning solvents be allowed to contaminate the slip clutch. Do not use grease on transmission input shaft. Should the damper become contaminated, it must be replaced.
  2. Using the Heavy Duty Floor Crane and Spreader Bar, position the engine and transaxle together. Install the 6 transaxle-to-engine bolts. Tighten to 48 N.m {4.8 kgf.m, 35 ft.lbf}. NOTE: When positioning the engine to the transaxle, care must be taken to maintain alignment of the damper spline with the transaxle input shaft. NOTE: Transaxle removed from view for clarity.
  3. Connect the high voltage wiring harness electrical connector. Engage the electrical connector locking tab.
  4. Using the Heavy Duty Floor Crane and Engine Lifting Bracket, position the engine and transaxle onto the Powertrain Lift.
  5. Using the Universal Adapter Brackets, secure the engine to the Powertrain Lift. NOTE: Due to the weight of the transaxle, special care should be taken to mount the powertrain securely to the Powertrain Lift.
  6. Raise the engine and transaxle into the vehicle.
  7. Install the upper transaxle insulator. Tighten the nuts to 90 N.m {9.0 kgf.m, 66 ft.lbf}. Tighten the through bolt to 103 N.m {10.3 kgf.m, 76 ft.lbf}.
  8. Install the upper transaxle insulator bracket. Tighten to 25 N.m {2.5 kgf.m, 18 ft.lbf}.
  9. Install the 3 engine mount bracket nuts. Tighten to 115 N.m {11.5 kgf.m, 85 ft.lbf}.
  10. Install the engine mount bracket bolt. Tighten to 115 N.m {11.5 kgf.m, 85 ft.lbf}.
  11. Using the Powertrain Lift, raise the subframe into position.
  12. Install the 2 subframe nuts. Tighten to 150 N.m {15.0 kgf.m, 111 ft.lbf}.
  13. Tighten the 2 subframe bolts. Tighten to 175 N.m {17.5 kgf.m, 129 ft.lbf}.
  14. Install the rear roll restrictor, bracket and bolts. Tighten to 55 N.m {5.5 kgf.m, 41 ft.lbf}.
  15. Connect the steering column coupling to the steering gear and install the new steering column coupling pinch bolt. Tighten to 40 N.m {4.0 kgf.m, 30 ft.lbf}.
  16. Install the rear transaxle insulator through bolt. Tighten to 115 N.m {11.5 kgf.m, 85 ft.lbf}.
  17. Install the 2 transaxle-to-engine bolts. Tighten to 48 N.m {4.8 kgf.m, 35 ft.lbf}.
  18. Install the 2 transaxle-to-engine bolts. Tighten to 48 N.m {4.8 kgf.m, 35 ft.lbf}.
  19. Install the engine support crossmember. Tighten the bolts to 90 N.m {9.0 kgf.m, 66 ft.lbf}. Tighten the new nut to 175 N.m {17.5 kgf.m, 129 ft.lbf}.
  20. Install the rear roll restrictor-to-crossmember through bolt. Tighten to 90 N.m {9.0 kgf.m, 66 ft.lbf}.
  21. Install the lower transaxle insulator through bolt. Tighten to 115 N.m {11.5 kgf.m, 85 ft.lbf}.
  22. Connect the lower radiator hose to the radiator.
  23. Install the A/C compressor and connect the A/C compressor electrical connector. Tighten to 25 N.m {2.5 kgf.m, 18 ft.lbf}.
  24. Install the auxiliary coolant pump and the electrical connector. Tighten to 10 N.m {1.0 kgf.m, 89 in.lbf}.
  25. Install the Motor Electronics Cooling System (MECS) pump and the ground strap. Install the 2 bolts. Tighten to 20 N.m {2.0 kgf.m, 177 in.lbf}.
  26. Connect the MECS pump electrical connector and attach the harness retainer.
  27. Install the wiring harness fasteners, the ground cable and nut. Tighten to 20 N.m {2.0 kgf.m, 177 in.lbf}.
  28. Connect the transaxle control cable. Install the transaxle control cable bracket and the 2 nuts finger-tight. Attach the transaxle control cable to the control lever.
  29. Position the control lever between the 2 casting ribs on the transaxle case.
  30. Place the gear selector lever in the D position.
  31. Tighten the transaxle control cable bracket nuts. Tighten to 22 N.m {2.2 kgf.m, 16 ft.lbf}.
  32. To verify the correct cable adjustment, observe the control lever on the transaxle while an assistant shifts the gear selector lever to each range position ending in the D position.
  33. Install the transaxle control snow shield. Tighten to 22 N.m {2.2 kgf.m, 16 ft.lbf}.
  34. Connect the transaxle coolant hoses.
  35. Connect the transaxle coolant temperature sensor electrical connector and pin-type retainer.
  36. Position the DC-to-DC converter in place and install the 3 nuts. Tighten to 12 N.m {1.2 kgf.m, 106 in.lbf}.
  37. Connect the DC-to-DC converter electrical connector and 2 wire harness retainers (1 shown in illustration). Engage the electrical connector locking tab.
  38. Connect the coolant vent hose.
  39. Connect the 2 low voltage electrical connectors and the engine harness-to-body harness retainer.
  40. Connect the transaxle harness electrical connector and install the stud bolt. Tighten to 10 N.m {1.0 kgf.m, 89 in.lbf}.
  41. Connect the transaxle selector lever cable fastener to the intake manifold.
  42. Install the transaxle selector lever cable fasteners on the transaxle stud bolts.
  43. Connect the upper evaporative emissions Evaporative Emission (EVAP) tube quick connect coupling to the purge valve.
  44. Connect the engine control harness electrical connector.
  45. If equipped, connect the block heater electrical connector. Attach the harness retainer clips.
  46. Connect the PCM electrical connector. Position the harness and install the wiring harness retainer.
  47. Connect the brake booster vacuum hose to the brake booster.
  48. Connect the upper radiator hose to the radiator.
  49. Connect the heater hoses to the heater core.
  50. If equipped, install the spin-on engine oil filter. Tighten the spin-on oil filter three-quarters of a turn after the oil filter gasket makes contact with the oil filter adapter.
  51. If equipped, install the oil filter element. NOTE: Lubricate the oil filter O-ring with clean engine oil before installation.

All wheel drive (AWD) vehicles

Scheme 853

Scheme 853
Scheme 853

Scheme 854

Scheme 854
Scheme 854

Scheme 855

Scheme 855
Scheme 855
  1. Using the Handle and PTO Driven Gear Oil Seal Installer, install the intermediate shaft seal.
  2. Position the Power Transfer Unit (PTU) in place and install the 4 bolts. Tighten to 45 N.m {4.5 kgf.m, 33 ft.lbf}.
  3. Connect the PTU vent hose.
  4. Install the PTU heat shield and the bolts. Tighten to 11 N.m {1.1 kgf.m, 97 in.lbf}.
  5. Position the PTU-to-engine support bracket and install the bolts. Tighten to 40 N.m {4.0 kgf.m, 30 ft.lbf}. NOTE: Catalytic converter manifold is removed for clarity.
  6. Install the 2 exhaust bracket bolts. Tighten to 25 N.m {2.5 kgf.m, 18 ft.lbf}.
  7. Install the driveshaft.

All vehicles

Scheme 856

Scheme 856
Scheme 856

Scheme 857

Scheme 857
Scheme 857

Scheme 858

Scheme 858
Scheme 858

Scheme 859

Scheme 859
Scheme 859

Scheme 860

Scheme 860
Scheme 860

Scheme 861

Scheme 861
Scheme 861

Scheme 862

Scheme 862
Scheme 862
  1. Connect the RH and LH suspension. Position the tie-rod end and install the retaining nut. Tighten to 55 N.m {5.5 kgf.m, 41 ft.lbf}. Connect the stabilizer bar link and install the nut. Tighten to 63 N.m {6.3 kgf.m, 46 ft.lbf}. NOTE: RH side shown in illustration, LH similar.
  2. Install the intermediate shaft.
  3. Install the 2 intermediate shaft bearing retainer nuts. Tighten to 27 N.m {2.7 kgf.m, 20 ft.lbf}.
  4. Install the RH brake hose retainer and the ABS sensor bolt. Tighten to 15 N.m {1.5 kgf.m, 133 in.lbf}.
  5. Install the LH brake hose retainer and the ABS sensor bolt. Tighten to 15 N.m {1.5 kgf.m, 133 in.lbf}.
  6. Install the exhaust intermediate pipe.
  7. Install the lateral support crossmember and the bolts. Tighten to 115 N.m {11.5 kgf.m, 85 ft.lbf}.
  8. Install the front wheels and tires. See «WHEEL AND TIRE REMOVAL/INSTALLATION»(ref-373095-S28507114572010100600000) .
  9. Connect the fuel supply tube.
  10. Install the accessory drive belt. See «ACCESSORY DRIVE BELT - HYBRID REMOVAL/INSTALLATION»(ref-373078-S34131091992010100600000) .
  11. Install the engine coolant degas bottle. See «DEGAS BOTTLE REMOVAL/INSTALLATION - HYBRID»(ref-373089-S12639818932010100600000) .
  12. Install the battery and the battery tray. See «BATTERY TRAY REMOVAL/INSTALLATION»(ref-348661-S24681863762009112700000) .
  13. Install the engine air cleaner. See «AIR CLEANER REMOVAL/INSTALLATION - HYBRID»(ref-373096-S19911542102010100600000) .
  14. Fill the engine with clean engine oil.
  15. Enable the vehicle high voltage electrical system. See «HIGH-VOLTAGE TRACTION BATTERY SYSTEMS DEPOWERING - HYBRID»(ref-373092-S23272902992010100600000) .
  16. Reset the Passive Anti-Theft System (PATS).
  17. Fill and bleed the MECS. See «MOTOR ELECTRONICS COOLING SYSTEM DRAINING AND FILLING - HYBRID»(ref-373100-S24369531972010100600000) .
  18. Fill and bleed the cooling system. See «COOLING SYSTEM DRAINING, FILLING AND BLEEDING -- 2.5L»(ref-348664-S29598792362009112700000) .
  19. Fill the transaxle with fluid.

Scheme 863

Scheme 863: LOWER ENGINE BLOCK - HYBRID EXPLODED VIEW
Scheme 863: LOWER ENGINE BLOCK - HYBRID EXPLODED VIEW
  1. For additional information, see the appropriate procedure(s).

Scheme 864

Scheme 864: FRONT ENGINE BLOCK - HYBRID EXPLODED VIEW
Scheme 864: FRONT ENGINE BLOCK - HYBRID EXPLODED VIEW
  1. For additional information, see the appropriate procedure(s).

Scheme 865

Scheme 865: INTAKE MANIFOLD - HYBRID EXPLODED VIEW
Scheme 865: INTAKE MANIFOLD - HYBRID EXPLODED VIEW
  1. For additional information, see the appropriate procedure(s).

Scheme 866

Scheme 866: CYLINDER HEAD - HYBRID EXPLODED VIEW
Scheme 866: CYLINDER HEAD - HYBRID EXPLODED VIEW
  1. For additional information, see the appropriate procedure(s).