ENGINE TECHNICAL DATA [MZI 3.7 V6]
ENGINE TECHNICAL DATA REFERENCE CHART Item Specification Ignition timing Approx. BTDC 13° Idle speed (P position) No load: 570-670 rpm Electrical load on: 570-730 rpm Power steering oil pump operation: 600-700 rpm A/C and heater operation: 570-745 rpm CO concentration Within the regulation HC concentration Within the regulation Standard valve clearance [Engine cold] IN: 0.150-0.250 mm {0.00591-0.00984 in} EX: 0.300-0.400 mm {0.0119-0.0157 in} Oil control valve resistance 5-14 ohms Engine oil capacity (approx. quantity) Oil replacement: 4.7 L {5.0 US qt, 4.1 Imp qt} Oil and oil filter replacement: 5.2 L {5.5 US qt, 4.6 Imp qt} Total (dry engine): 5.7 L {6.0 US qt, 5.0 Imp qt} Oil pressure (reference value) [oil temperature: 93.3°C {200 °F}] 310-621 kPa {3.17-6.33 kgf/cm 2 , 45.0-90.0 psi} [2,000 rpm] Engine coolant capacity (approx. quantity) 9.8 L {10 US qt, 8.6 Imp qt} Cooling system cap valve opening pressure 93-123 kPa {0.95-1.25 kgf/cm 2 , 14.0-17.8 psi} Thermostat initial-opening temperature 79.5-83.3°C {176-181 °F} Thermostat full-open temperature 94.5°C {202 °F} Thermostat full-open lift More than 8.1 mm {0.32 in} Cooling fan motor No. 1, No. 2 standard current 22.5-25.5 A [12 V] Fuel line pressure 375-450 kPa {3.83-4.58 kgf/cm 2 , 54.4-65.2 psi} Fuel injector resistance 11.3-12.7 ohms [20°C {68 °F}] Battery electrolyte specific gravity [20°C {68 °F}] 1.22-1.29 Battery back-up current (When the ignition is off (key is removed) and all doors are closed.) 50-65 mA Generator standard voltage [IG-ON] Terminal B: B+ Terminal A: B+ Terminal RC: Approx. 1 V or less Terminal LI: Approx. 1 V Generator standard voltage [Idle, 20°C {68 °F}] Terminal B: 12-16 V Terminal A: 12-16 V Terminal RC: 0-16 V Terminal LI: 1-16 V Generator generated current minimum value 70% of the nominal output current (nominal output current: 110 A) [Ambient temp. 20°C {68 °F}, voltage 13.0-15.0 V, both engine and generator are hot] Generator rotor resistance (between slip rings) [20°C {68 °F}] 1.8-2.2 ohm Generator brush length Standard: 22.5 mm {0.886 in} Minimum: 5.0 mm {0.20 in} Generator brush spring force Standard: 4.1-5.3 N {0.42-0.54 kgf, 1.0-1.1 lbf} Minimum: 1.7 N {0.17 kgf, 0.38 lbf} Firing order 1-4-2-5-3-6 Ignition coil secondary coil resistance 5-6 kilohms Spark plug type CY01 18110(AYFS22FM) Spark plug gap 1.29-1.45 mm {0.051-0.057 in} Spark plug resistance 2-20 kilohms Starter no-load test voltage 11V Starter no-load test current 90 A or less Starter pinion gap 0 mm {0 in} Starter armature runout 0.1 mm (0.004 in} max. Starter commutator diameter Standard: 29.4 mm {1.16 in} Minimum: 28.8 mm {1.13 in} Segment groove depth of starter commutator Standard: 0.5 mm {0.02 in} Minimum: 0.2 mm {0.008 in} Starter brush length Standard: 12.3 mm {0.484 in} Minimum: 5.5 mm {0.22 in} Starter brush spring force Standard: 15.0-20.4 N {1.53-2.08 kgf, 3.38-4.58 lbf} Minimum: 2.75 N {0.280 kgf, 0.618 lbf}