Service Specifications: Specifications — Lexus SC II рестайлинг (2005-2010)

SPECIFIED TORQUE FOR STANDARD BOLTS

Class	Diameter (mm)	Pitch (mm)	Specified torque
			Hexagon head bolt			Hexagon flange bolt
			N*m	Kgf*cm	Ft.*lbf	N*m	Kgf*cm	Ft.*lbf
4T	6	1	5	55	48 in.*lbf	6	60	52 in.*lbf
	8	1.25	12.5	130	9	14	145	10
	10	1.25	26	260	19	29	290	21
	12	1.25	47	480	35	53	540	39
	14	1.5	74	760	55	84	850	61
	16	1.5	115	1,150	83
5T	6	1	6.5	65	56 in.*lbf	7.5	75	65 in.*lbf
	8	1.25	15.5	160	12	17.5	175	13
	10	1.25	32	330	24	36	360	26
	12	1.25	59	600	43	65	670	48
	14	1.5	91	930	67	100	1,050	76
	16	1.5	140	1,400	101
6T	6	1	8	80	69 in.*lbf	9	90	78 in.*lbf
	8	1.25	19	195	14	21	210	15
	10	1.25	39	400	29	44	440	32
	12	1.25	71	730	53	80	810	59
	14	1.5	110	1,100	80	125	1,250	90
	16	1.5	170	1,750	127
7T	6	1	10.5	110	8	12	120	9
	8	1.25	25	260	19	28	290	21
	10	1.25	52	530	38	58	590	43
	12	1.25	95	970	70	105	1,050	76
	14	1.5	145	1,500	108	165	1,700	123
	16	1.5	230	2,300	166
8T	8	1.25	29	300	22	33	330	24
	10	1.25	61	620	45	68	690	50
	12	1.25	110	1,100	80	120	1,250	90
9T	8	1.25	34	340	25	37	380	27
	10	1.25	70	710	51	78	790	57
	12	1.25	125	1,300	94	140	1,450	105
10T	8	1.25	38	390	28	42	430	31
	10	1.25	78	800	58	88	890	64
	12	1.25	140	1,450	105	155	1,600	116
11T	8	1.25	42	430	31	47	480	35
	10	1.25	87	890	64	97	990	72
	12	1.25	155	1,600	116	175	1,800	130

SPECIFIED TORQUE FOR STANDARD BOLTS

TORQUE SPECIFICATIONS

Part Tightened	N*m	Kgf*cm	Ft.*lbf
Camshaft timing oil control valve assembly at Cylinder head cover	8.5	87	75 in.*lbf
V-bank cover at Engine	5.0	51	44 in.*lbf
Intake air connector pipe at Engine	5.0	51	44 in.*lbf
No. 1 air cleaner inlet at Body	5.0	51	44 in.*lbf
No. 3 timing belt cover sub-assembly LH at Engine	7.5	76	66 in.*lbf
Intake manifold at Cylinder head	18	184	13
Purge VSV at Intake manifold	18	184	13
No. 1 V-bank cover bracket at Intake manifold	7.5	76	66 in.*lbf
No. 2 V-bank cover bracket at Intake manifold	18	184	13
No. 3 V-bank cover bracket at Intake manifold	7.5	76	66 in.*lbf
No. 4 V-bank cover bracket at Intake manifold	18	184	13
VVT sensor at Cylinder head cover	7.5	76	66 in.*lbf
Crankshaft position sensor at Cylinder block	6.5	66	57 in.*lbf
Engine coolant temperature sensor at Water inlet	20	204	15
Throttle body at Intake manifold	18	184	13
Knock sensor at Cylinder block sub-assembly	20	204	15
ECM at ECM box	5.5	56	49 in.*lbf
ECM box cover at ECM box	5.0	51	44 in.*lbf
Accelerator pedal rod at Body	5.0	51	44 in.*lbf

3UZ-FE ENGINE CONTROL SYSTEM - TORQUE SPECIFICATIONS

Part tightened		N*m	Kgf*cm	Ft.*lbf
Exhaust manifold sub-assembly at Cylinder head		44	449	32
Intake manifold assembly at Cylinder head		18	184	13
Engine hanger at Cylinder head		37	377	27
Drive plate & ring gear sub-assembly at Crankshaft	1st	49	500	36
Drive plate & ring gear sub-assembly at Crankshaft	2nd	Turn 90°	Turn 90°	Turn 90°
Drive plate & ring gear sub-assembly at Torque converter clutch		48	489	35
Flywheel housing under cover at Transmission		18	184	13
Engine rear mounting member at Body		25.5	260	19
Engine rear mounting member at Rear engine mounting insulator		13.5	138	10
Front suspension crossmember at Engine mounting insulator		68	693	50
Power steering gear housing assembly at Front suspension crossmember		65	662	48
Steering sliding yoke sub-assembly at Steering intermediate shaft		35	357	26
Cooler compressor assembly at Idler pulley assembly		49	500	36
Cooler compressor stay at Oil filter bracket		29	296	21
Vane pump assembly at Cylinder head	Bolt	39.2	400	29
Vane pump assembly at Cylinder head	Nut	43.1	439	32
Engine mounting bracket front at Cylinder block		36	367	27
Oil filter bracket sub-assembly at Engine		18	184	13
Rear water bypass pipe joint at Cylinder head		18	184	13
Front water bypass pipe joint at Cylinder block		18	184	13
Oil dipstick guide at Cylinder head		15	153	11
Camshaft drive gear at Camshaft timing tube assembly		7.5	76	66 in.*lbf
Camshaft timing tube assembly at Camshaft		78	795	58
Screw plug at Camshaft timing tube assembly		15	153	11
Engine rear oil seal retainer at Cylinder block		8.0	76	71 in.*lbf
Cylinder head at Cylinder block	1st	59	602	44
Cylinder head at Cylinder block	2nd	Turn 90°	Turn 90°	Turn 90°
Camshaft bearing cap at Cylinder head	Front bearing cap (w/o seal washer)	7.5	76	66 in.*lbf
Camshaft bearing cap at Cylinder head	Others	16	163	12
Camshaft timing pulley at Camshaft timing tube assembly		7.5	76	66 in.*lbf
No. 1 timing belt idler sub-assembly at Oil pump		34.5	352	25
No. 2 timing belt idler sub-assembly at Oil pump		34.5	352	25
Timing belt tensioner at Oil pump		26	265	19
Crankshaft damper sub-assembly at Crankshaft		245	2,498	181
Idler pulley assembly at Cylinder block	12 mm head	16	163	12
Idler pulley assembly at Cylinder block	14 mm head	32	326	24
V-ribbed belt tensioner assembly at Cylinder block		16	163	12
No. 2 timing belt cover sub-assembly at Cylinder block		16	163	12
No. 2 idler pulley sub-assembly at Idler pulley assembly		39	398	29
Cylinder head cover sub-assembly at Cylinder head		6.0	61	53 in.*lbf
Crankshaft bearing cap at Cylinder block	2 progressive type 1st	27	275	20
	2nd	Turn 90°	Turn 90°	Turn 90°
	Others	49	500	36
Connecting rod cap at Connecting rod	1st	24.5	250	18
Connecting rod cap at Connecting rod	2nd	Turn 90°	Turn 90°	Turn 90°
Water seal plate at Cylinder block		14	142	10
Cylinder block water drain cock sub-assembly at Cylinder block		49	500	36
Exhaust manifold LH at Cylinder head		44	449	32
Heat insulator at Exhaust manifold LH		7.5	76	66 in.*lbf
Exhaust manifold RH at Cylinder head		44	449	32
Heat insulator at Exhaust manifold RH		7.5	76	66 in.*lbf
Camshaft bearing cap at Cylinder head: for 21 and 22 bolts		16	163	12
Camshaft bearing cap at Cylinder head: for other bolts		7.5	76	66 in.*lbf
Ignition coil at Cylinder head cover		7.5	76	66 in.*lbf
No. 1 air cleaner inlet at Body		5.0	51	44 in.*lbf
V-bank cover at No. 1 V-bank cover bracket		5.0	51	44 in.*lbf
V-bank cover at No. 2 V-bank cover bracket		5.0	51	44 in.*lbf
Intake air connector pipe at Body		5.0	51	44 in.*lbf
ECM cover at ECM box		5.0	51	44 in.*lbf
Catalyst converter at Exhaust manifold		62	632	46
Front exhaust pipe at Catalyst converter		43	438	32
Front exhaust pipe at Center exhaust pipe		43	438	32
Front floor brace center at Body		13	132	10
Propeller with center bearing shaft at Transmission		79	806	58
Propeller with center bearing shaft at Differential		79	806	58
Propeller with center bearing shaft at Body		37	377	27
No. 1 front floor heat insulator at Body		5.0	51	44 in.*lbf
Parking brake cable head insulator at Body		5.0	51	44 in.*lbf
No. 1 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
No. 2 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
No. 3 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
No. 4 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
Throttle body at Intake manifold		18	184	13
Camshaft oil control valve at Cylinder head cover		7.5	76	66 in.*lbf
Camshaft position sensor at Cylinder head		7.5	76	66 in.*lbf
No. 3 timing belt cover at Cylinder head		7.5	76	66 in.*lbf
Transmission assembly at Engine assembly: for bolt A		37	377	27
Transmission assembly at Engine assembly: for bolt B		71	724	52
No. 1 exhaust pipe support bracket at Transmission		43	438	32
Timing belt tensioner at Cylinder block		26	265	19
Water pump at Cylinder block: for bolts		21	214	15
Water pump at Cylinder block: for stud bolts and nuts		18	184	13

3UZ-FE ENGINE MECHANICAL - TORQUE SPECIFICATIONS

Part Tightened		N*m	Kgf*cm	Ft.*lbf
V-bank cover at engine		5.0	51	44 in.*lbf
Intake air connector pipe at engine		5.0	51	44 in.*lbf
No. 1 air cleaner inlet at engine		5.0	51	44 in.*lbf
Fuel pressure pulsation damper assembly at Fuel delivery pipe sub-assembly	With SST	33	337	24
	Without SST	39	397	29
Fuel delivery pipe sub-assembly at Intake manifold		21	214	15
Purge VSV at Intake manifold		18	184	13
No. 1 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
No. 2 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
No. 3 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
No. 4 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
Fuel tank vent tube set plate at Fuel tank		6.0	61	52 in.*lbf
Fuel pump resistor at Body		8.0	82	71 in.*lbf
Fuel sender gauge at Fuel tank		1.5	15	13 in.*lbf
Fuel tank band at Body		39.2	400	29

3UZ-FE FUEL - TORQUE SPECIFICATIONS

Part Tightened		N*m	Kgf*cm	Ft.*lbf
Canister assembly at Body		5.5	56	49 in.*lbf
Under cover at Body		5.4	55	48 in.*lbf
Rear suspension member brace at Body		50	510	37
Rear drive shaft assembly RH at Differential		83	850	61
V-bank cover at Engine		5.0	51	44 in.*lbf
Intake air connector pipe at Engine		5.0	51	44 in.*lbf
No. 1 air cleaner inlet at Body		5.0	51	44 in.*lbf
Purge VSV at Intake manifold		18	184	13
Ventilation valve sub-assembly at Cylinder head cover		27	275	20
Heated oxygen sensor (for sensor 1) at Front pipe	With SST	40	408	30
Heated oxygen sensor (for sensor 1) at Front pipe	Without SST	44	449	32
Heated oxygen sensor (for sensor 2) at Center, pipe	With SST	40	408	30
Heated oxygen sensor (for sensor 2) at Center, pipe	Without SST	44	449	32

3UZ-FE EMISSION CONTROL - TORQUE SPECIFICATIONS

Part tightened		N*m	Kgf*cm	Ft.*lbf
Vacuum switching valve at Vacuum tank		1.4	14	12 in.*lbf
Intake air control valve at Intake manifold upper		8.5	87	75 in.*lbf
Intake air control valve at Intake manifold upper		8.5	87	75 in.*lbf
Intake manifold upper at Intake manifold lower		18	184	13
Vacuum control valve at Intake manifold lower		18	184	13
Intake manifold at Cylinder head		18	184	13
No. 2 fuel pipe at Fuel main hose	With SST	28	286	21
No. 2 fuel pipe at Fuel main hose	Without SST	35	357	26
Purge VSV at Intake manifold		7.5	76	66 in.*lbf
No. 4 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
No. 3 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
No. 2 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
No. 1 V-bank cover bracket at Intake manifold		7.5	76	66 in.*lbf
Intake air connector pipe x	For hose clamp	4.0	41	35 in.*lbf
Intake air connector pipe x	For bolt	5.0	51	44 in.*lbf
V-bank cover at V-bank cover bracket		5.0	51	44 in.*lbf

3UZ-FE INTAKE - TORQUE SPECIFICATIONS

Part tightened		N*m	Kgf*cm	Ft.*lbf
Exhaust manifold at Cylinder block		44	449	32
Exhaust manifold heat insulator at Exhaust manifold		7.5	76	66 in.*lbf
Heated oxygen sensor at Exhaust manifold	With SST	40	408	30
Heated oxygen sensor at Exhaust manifold	Without SST	44	449	32
Catalyst converter at Exhaust manifold		62	632	46
No. 1 exhaust pipe support bracket at Exhaust manifold		43	438	32
Exhaust front pipe at Catalyst converter		43	438	32
Exhaust center pipe at Exhaust front pipe		43	438	32
Front floor brace center at Body		13	133	10
Exhaust tailpipe at Exhaust center pipe		43	438	32
Exhaust tailpipe at Baffle		8.0	82	71 in.*lbf
No. 2 heated oxygen sensor at Exhaust center pipe		44	449	32

3UZ-FE EXHAUST - TORQUE SPECIFICATIONS

Part tightened		N*m	Kgf*cm	Ft.*lbf
Cylinder block drain cock plug at Cylinder block		13	133	10
No. 1 air cleaner inlet at Fan Shroud		5.0	51	44 in.*lbf
V-bank cover at Intake manifold		5.0	51	44 in.*lbf
Water pump at Timing chain cover	For bolt	21	214	15
Water pump at Timing chain cover	For nut and stud bolt	18	184	13
Water inlet housing at Water pump		18	184	13
Water inlet at Water inlet housing		19	194	14
Cooling fan motor at Fan shroud		5.0	51	44 in.*lbf
No. 2 cooling fan motor at Fan shroud		5.0	51	44 in.*lbf
Fan at Cooling fan motor		5.0	51	44 in.*lbf
Fan shroud at Radiator		5.0	51	44 in.*lbf
Plate washer at Oil cooler		8.4	86	74 in.*lbf
Inlet at Plate washer		14.7	150	11
Radiator support bracket at Radiator support upper		13.5	138	10

3UZ-FE COOLING - TORQUE SPECIFICATIONS

Part tightened		N*m	Kgf*cm	Ft.*lbf
No. 2 Drain plug at Oil pan sub-assembly		39	398	29
Oil pump body cover at Oil pump body		10	102	7
Oil pump body at Plug for relief valve		49	500	36
Oil pump assembly at Cylinder block	12 mm head and 6 mm hexagon head	15.5	158	11
Oil pump assembly at Cylinder block	14 mm head	30.5	311	22
Oil strainer at Cylinder block, Oil pump assembly		7.5	76	66 in.*lbf
Oil pan sub-assembly at Oil pump assembly, Rear oil seal retainer		7.5	76	66 in.*lbf
Oil pan sub-assembly at Cylinder block	10 mm head	7.5	76	66 in.*lbf
Oil pan sub-assembly at Cylinder block	12 mm head and nut	28	286	21
Oil pan baffle plate at Oil pan sub-assembly		7.5	76	66 in.*lbf
No. 2 Oil pan sub-assembly at Oil pan sub-assembly		7.5	76	66 in.*lbf
Oil level sensor at Oil pan sub-assembly		6.9	70	61 in.*lbf
Crank position sensor at Oil pump assembly		6.5	66	58 in.*lbf
Oil filter bracket sub-assembly at Oil pump assembly		18	184	13

3UZ-FE LUBRICATION - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Spark plug at Cylinder head	18	183	13
Ignition coil at Cylinder head cover	7.5	76	66 in.*lbf

3UZ-FE IGNITION - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Starter wire clamp at Wire bracket	9.8	100	87 in.*lbf
Starter wire at Starter assembly	9.8	100	87 in.*lbf
End cover at Brush holder	3.8	39	34 in.*lbf
Starter housing at Magnetic switch	9.3	95	82 in.*lbf
End cover with starter yoke at Starter housing	9.3	95	82 in.*lbf
Lead wire of starter yoke at Terminal C	5.9	60	52 in.*lbf
Starter assembly at Cylinder block	39	398	29

3UZ-FE STARTING - TORQUE SPECIFICATIONS

Part tightened		N*m	Kgf*cm	Ft.*lbf
Generator at Cylinder block	For bolt and nut A	39	398	29
Generator at Cylinder block	For nut B	15	153	11
Vane pump at Vane pump pulley		43	438	32
Coil assembly at Drive end frame		5.8	59	51 in.*lbf
Generator pulley at Rotor		111	1,132	82
Brush holder assembly at Coil assembly		1.8	18	16 in.*lbf
Rear end cover at Coil assembly		4.6	47	41 in.*lbf

3UZ-FE CHARGING - TORQUE SPECIFICATIONS

AUTOMATIC TRANSMISSION ASSEMBLY

Part tightened	N*m	Kgf*cm	Ft.*lbf
Refill plug at Transmission assembly	39	398	29
Overflow plug at Transmission assembly	20	204	15
Transmission case cover at Transmission assembly	5.4	55	48 in.*lbf
Park/neutral position switch at Set bolt	13	133	10
Control shaft lever at Park/neutral position switch	16	163	12
Lock nut at Park/neutral position switch	6.9	70	61 in.*lbf
Engine rear mounting member at Body	26	265	19
Floor shift gear shifting rod at Shift lever assembly	13	133	10
Transmission revolution sensor at Transmission assembly	5.4	55	48 in.*lbf
Drain plug at Transmission assembly	20	205	15
Transmission control shaft lever RH at Park/neutral position switch	16	163	12
Engine mounting insulator rear No.1 at Transmission assembly	12	122	9
Transmission assembly at Engine 17 mm head	71	724	52
Transmission assembly at Engine 14 mm head	37	377	27
Torque converter clutch at Drive plate	48	489	35
Flywheel housing under cover at Transmission assembly	18	184	13
Wire harness at Transmission assembly Bolt A	71	724	52
Wire harness at Transmission assembly Bolt B	10	102	7
Engine rear mounting member at Engine mounting insulator rear No.1	13	133	10
Oil cooler tube clamp at Transmission assembly	5.0	50	43 in.*lbf
Oil cooler outlet tube No.1 at Transmission assembly	44	449	32
Oil cooler inlet tube No.1 at Transmission assembly	44	449	32
Exhaust pipe No.1 support bracket at Transmission assembly	43	438	32
Transmission wire at Transmission assembly	5.4	55	48 in.*lbf
Clamp at Transmission valve body Bolt A	6.4	65	57 in.*lbf
Clamp at Transmission valve body Bolt B	10	102	7
ATF temperature sensor at Transmission valve body	10	102	7
Valve body oil strainer assembly at Transmission valve body	10	102	7
Automatic transmission oil pan at Transmission assembly	4.4	44	39 in.*lbf
Floor shift assembly at Body	8.3	85	74 in.*lbf

AUTOMATIC TRANSMISSION ASSEMBLY - TORQUE SPECIFICATIONS

AUTOMATIC TRANSMISSION UNIT

Part tightened	N*m	Kgf*cm	Ft.*lbf
Transmission housing at Transmission case: Bolt length 14 mm	34	345	25
Transmission housing at Transmission case: Bolt length 17 mm	57	581	42
Automatic transaxle breather tube at Transmission case	5.4	55	48 in.*lbf
Park/Neutral position switch assembly: Bolt	13	130	9
Park/Neutral position switch assembly: Nut	6.9	70	61 in.*lbf
Transmission wire at Transmission case	5.4	55	48 in.*lbf
Oil cooler tube union at Transmission case	29	296	21
Transmission control shaft lever RH set nut	16	163	12
Transmission revolution sensor at Transmission case	5.4	55	48 in.*lbf
Extension housing assembly at Transmission case	34	345	25
Oil pan at Transmission case	4.4	45	39 in.*lbf
Valve body oil strainer assembly at Transmission valve body assembly	10	102	7
Transmission valve body assembly at Transmission case	11	110	8
Parking lock pawl bracket at Transmission case	7.4	75	65 in.*lbf
Drain plug	20	204	15
Over flow plug	20	204	15
Flange yoke at Output shaft	126	1,285	93
Oil pump at Transmission case	21	214	15
Oil pump body at Stator shaft assembly	11	110	8
Detent spring at Transmission valve body assembly	10	102	7
Lock plate at Transmission valve body assembly	6.4	65	57 in.*lbf
Solenoid valve (SL1, SLT) at Valve body	6.4	65	56 in.*lbf
Solenoid valve (SR) at Valve body	10	102	7
Solenoid valve (S1) at Valve body	10	102	7
Solenoid valve (S2, S4) at Valve body	10	102	7
Solenoid valve (S3) at Valve body	10	102	7
Solenoid valve (SLU, SL2) at Valve body	6.4	65	56 in.*lbf
Valve body at Transmission assembly	11	112	8
ATF Temperature sensor at Transmission valve body assembly	10	102	7
Transmission wire at Transmission valve body assembly	10	102	7

AUTOMATIC TRANSMISSION UNIT - TORQUE SPECIFICATIONS

Part Tightened	N*m	Kgf*cm	Ft.*lbf
Intermediate shaft assembly at Adjusting nut for use without SST	69	700	51
Intermediate shaft assembly at Adjusting nut for use with SST	51	520	38
Front floor No. 1 heart insulator at Body	5.4	55	48 in.*lbf
Parking brake cable heat insulator at Body	5.4	55	48 in.*lbf
Propeller shaft assembly at Automatic transmission companion flange	79	805	58
Propeller shaft assembly at Rear Differential companion flange	79	805	58
Center No. 1 support bearing assembly at Body	37	375	27
Front floor center brace at Body	20	204	15

PROPELLER SHAFT - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Front wheel set nut	103	1,050	76
Rear drive shaft at Rear axle shaft nut	289	2,947	213
Rear upper control arm assembly LH at Rear axle carrier assembly	108	1,101	80
Toe control link sub-assembly LH at Rear axle carrier assembly	59	600	44
Rear No. 1 suspension arm assembly LH at Rear axle carrier assembly	75	765	55
Rear No. 2 suspension arm assembly LH at Rear axle carrier assembly	110	1,122	81
Rear speed sensor at Rear axle carrier assembly	7.8	80	69 in.*lbf
No. 3 parking brake cable assembly at Rear axle carrier assembly	7.8	80	69 in.*lbf
Rear disc brake cylinder assembly at Rear axle carrier assembly	104	1,061	77
Rear suspension member brace at Body	50	510	37

DRIVE SHAFT - TORQUE SPECIFICATIONS

Part tightened		N*m	Kgf*cm	Ft.*lbf
Propeller intermediate shaft at Transmission		79	805	58
Propeller shaft at Companion flange		79	805	58
Center support bearing at Body		37	375	27
Front floor No. 1 heat insulator set bolt		5.4	55	48 in.*lbf
Parking brake cable heat insulator set bolt		5.4	55	48 in.*lbf
Oxygen sensor at Exhaust pipe		44	450	32
Rear suspension member brace rear lower at Body		23	235	17
Front floor brace center at Body		20	204	15
Rear suspension No. 1 arm at Rear axle carrier		75	765	55
Rear suspension No. 2 arm at Rear axle carrier		110	1,120	81
Rear drive shaft at Side gear shaft		83	850	61
Rear drive shaft set nut		289	2,950	213
Differential carrier set nut	Front side	123	1,250	90
Differential carrier set nut	Rear side	142	1,450	105
Rear suspension member brace set bolt		50	510	37
Body Rear end mounting bracket sub-assembly at Body	Bolt (A)	103	1,050	76
	Bolt (B)	69	704	51
	Nut	54	551	40
Rear end body mounting set plate at Body		56	570	41
Drain plug		49	500	39
Filler plug		49	500	39
Breather plug		21	210	15
Companion flange at Drive pinion		98 to 490	1,000 to 5,000	72 to 361
Differential case at Ring gear		64	650	47
Differential carrier at Differential carrier cover		47	475	35
Oil deflector set bolt		7.0	70	62 in.*lbf

DIFFERENTIAL - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Front wheel set bolt	103	1,050	76
Steering knuckle at Lower ball joint assembly	113	1,152	83
Steering knuckle at Upper suspension arm	87	887	64
Front axle hub nut at Front axle hub sub-assembly	199	2,030	147
Steering knuckle at Front disc brake cylinder assembly	118	1,203	87
Steering knuckle at Front speed sensor	8.5	87	75 in.*lbf
Rear wheel set nut	103	1,050	76
Rear drive shaft at Rear axle shaft nut	289	2,947	213
Rear axle carrier at Toe control link sub-assembly	59	602	44
Rear axle carrier at Rear upper control arm assembly	108	1,101	80
Rear axle carrier at Rear No. 1 suspension arm assembly	75	765	55
Rear axle carrier at Rear No. 2 suspension arm assembly	289	2,947	213
Rear axle carrier at Parking brake anchor block sub-assembly	76	775	56
Rear axle carrier at Rear speed sensor	7.8	80	69 in.*lbf
Rear axle carrier at Rear disc brake cylinder assembly	104	1,061	77
Rear axle carrier at No. 3 parking brake cable assembly	7.8	80	69 in.*lbf

AXLE - TORQUE SPECIFICATIONS

Part tightened		N*m	Kgf*cm	Ft.*lbf
Tie rod end lock nut		56	570	41
Front shock absorber at Body		56	570	41
Front shock absorber at Front shock absorber bracket		157	1,600	116
Suspension support at Piston rod		28	286	21
Upper arm at Steering knuckle		87	890	64
Upper arm at Body		53	540	39
ABS speed sensor wire harness bracket set bolt		5.0	51	44 in.*lbf
Lower arm at Front shock absorber bracket		59	600	44
Lower arm at Steering knuckle		162	1,650	19
Lower arm at Suspension member		172	1,755	127
Lower arm at Suspension arm sub-assembly lower No. 2		164	1,690	121
Steering gear at Suspension member		65	663	48
Height control link at Front shock absorber bracket		5.4	55	48 in.*lbf
Suspension arm sub-assembly lower No. 2 at Strut bracket		152	1,550	112
Suspension member at Front suspension member brace sub-assembly RH		56	570	41
Front suspension member brace at Body		58	590	43
Lower ball joint assembly front at Front suspension lower arm assembly		162	1,650	119
Lower ball joint assembly front at steering knuckle		113	1,150	83
Lower ball joint assembly front at Tie rod end		87	890	64
Lower arm at Front stabilizer link		113	1,150	83
Front stabilizer bar at Stabilizer link		51	520	38
Hub nut		103	1,050	76
Wheel hub ornament		20	204	15
Piston rod set nut		28	286	21
Rear shock absorber at Body	Upper side	64	650	47
Rear shock absorber at Body	Lower side	18	184	13
Rear shock absorber at Rear suspension arm		110	1,120	81
Rear suspension arm at Axle carrier		110	1,120	81
Rear suspension arm at Suspension member		110	1,120	81
Upper control link sub-assembly at Body	Front side	88	900	65
Upper control link sub-assembly at Body	Rear side	74	755	55
Rear suspension No. 1 arm assembly at Axle carrier		75	765	55
Rear suspension No. 1 arm assembly at Body		75	765	55
Rear suspension No. 2 arm assembly at Height control sensor link		30	306	22
Toe control link sub-assembly at Body		49	500	36
Toe control link sub-assembly at Axle carrier		59	600	44
Toe control link sub-assembly at Speed sensor wire		5.0	51	44 in.*lbf
Rear stabilizer bracket at Body		18	185	13
Rear stabilizer bar at Rear stabilizer link		65	663	48
Rear end body mounting set plate at Body		56	570	29
Exhaust pipe		43	438	32
Wheel hub ornament		20	204	15

SUSPENSION - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Tire pressure warning valve at Disc wheel	3.0	31	27 in.*lbf
Tire pressure antenna front at Body	7.8	80	69 in.*lbf
Tire pressure antenna rear at Body	7.8	80	69 in.*lbf
Tire pressure warning receiver at Brace	9.0	92	80 in.*lbf
Hub nut	103	1,050	76
Wheel hub ornament	20	204	15

TIRE AND WHEEL - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Front speed sensor at Steering knuckle	8.0	82	71 in.*lbf
Front speed sensor harness clamp	5.0	51	44 in.*lbf
Rear speed sensor at Axle hub	8.0	82	71 in.*lbf
Rear speed sensor harness clamp	5.0	51	44 in.*lbf
Yaw rate sensor at Body	13	130	9
Steering wheel assembly at Horn button assembly	8.8	90	78 in.*lbf
Steering wheel assembly set nut	50	510	37
Skid control ECU set bolt	5.0	51	44 in.*lbf

BRAKE CONTROL - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Bleeder plug	11	110	8
Brake booster clevis lock nut	26	265	19
Brake pedal shaft nut	37	375	27
Brake booster pump at Brake booster accumulator	54	550	36
Brake master cylinder at No. 2 brake booster pump bracket	7.8	80	69 in.*lbf
Brake booster pump at No. 1 brake booster pump bracket	7.8	80	69 in.*lbf
Brake booster pump at Brake booster pump bracket	12	122	8.9
Brake booster pump at No. 3 bake booster pump bracket	12	122	8.9
Brake booster pump at Brake control wire	2.9	30	26 in.*lbf
Brake master cylinder at Brake control wire	1.7	17.5	15 in.*lbf
Brake master cylinder at No. 1 brake master cylinder union	32	326	23
Brake master cylinder at No. 2 brake master cylinder union	32	326	23
Brake tube flare nut (without SST)	15	155	11
Brake tube flare nut (with SST)	14	143	10
Brake master cylinder at No. 1 brake actuator bracket	8.5	87	75 in.*lbf
Brake master cylinder at No. 3 brake actuator bracket	7.8	80	69 in.*lbf
Brake master cylinder at Master cylinder reservoir	1.7	17.5	15 in.*lbf
Brake master cylinder at Body	15	155	11
Body at Brake line	4.9	50	43 in.*lbf
Front disc brake cylinder mounting at Steering knuckle	118	1,200	87
Front disc brake cylinder at Front disc brake cylinder mounting	34	350	25
Flexible hose at Front disc brake cylinder	30	310	22
Rear disc brake cylinder assembly at Axle hub	104	1,065	77
Flexible hose at Rear disc brake cylinder assembly	30	310	22

BRAKE - TORQUE SPECIFICATIONS

Part Tightened	N*m	Kgf cm	Ft.*lbf
Parking brake control pedal assembly	19	195	14
Parking brake release cable sub-assembly	5.4	55	48 in.*lbf
No. 1 parking brake cable lock nut	5.4	55	48 in.*lbf
No. 1 parking brake cable assembly at Body (Bolt)	7.8	80	69 in.*lbf
No. 1 parking brake cable assembly at Body (Nut)	5.4	55	48 in.*lbf
Intermediate lever bracket sub-assembly at Body	5.4	55	48 in.*lbf
No. 2 parking brake cable assembly at Body (Bolt A)	18.6	190	19
No. 2 parking brake cable assembly at Body (Bolt B)	5.4	55	48 in.*lbf
No. 2 parking brake cable assembly at Backing plate	7.8	80	69 in.*lbf
No. 3 parking brake cable assembly at Body (Bolt A)	18.6	190	19
No. 3 parking brake cable assembly at Body (Bolt B)	5.4	55	48 in.*lbf
No. 3 parking brake cable assembly at Backing plate	7.8	80	69 in.*lbf
Wheel nut	103	1,050	76
Ornament	20	204	15

PARKING BRAKE - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Tilt steering gear assembly at Tilt steering slider sub-assembly	23	230	17
Tilt steering gear assembly at Steering intermediate shaft assembly No. 2	35	360	26
Steering column assembly set bolt and nut	25	260	19
Steering column assembly at Steering sliding yoke sub-assembly	35	360	26
Steering wheel set nut	50	510	37
Steering wheel pad set screw ("TORX" screw)	8.8	90	78 in.*lbf

STEERING COLUMN - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
VANE PUMP ASSEMBLY
Vane pump housing sub-assembly front at Vane pump bracket rear	39	400	29
Power steering solenoid valve assembly at Vane pump housing sub-assembly front	51	520	38
Suction port union set bolt	13	130	9
Air control valve assembly at Vane pump housing sub-assembly front	29	300	22
Vane pump pulley set nut	43	440	32
Vane pump assembly set nut	43	440	32
Vane pump assembly set nut	39	400	29
Union bolt	49	500	36
RACK & PINION POWER STEERING GEAR ASSEMBLY
Cylinder end stopper at Power steering rack housing sub-assembly	59	600	43
Bearing guide nut	25	250	18
Control valve housing at Power steering rack housing	18	180	13
Steering rack guide spring cap	25	250	18
Steering rack guide spring nut	51	520	38
Steering rack end sub-assembly at Power steering rack	76	770	56
Tire rod assembly lock nut	56	570	41
Steering left and right turn pressure tube at power steering rack housing	23	240	17
Rack & pinion power steering gear assembly set bolt	65	660	48
Tube clamp set bolt	5.0	55	48 in.*lbf
Pressure feed and return tube set union bolt	49	500	36
Tie rod assembly at Lower ball joint	87	890	64
Front suspension member brace sub-assembly RH	58	590	43
Front suspension member brace rear LH	58	590	43
Front suspension member brace rear RH	58	590	43

POWER STEERING - TORQUE SPECIFICATIONS

REFRIGERANT LINE

Part tightened	N*m	Kgf*cm	Ft.*lbf
No. 1 cooler refrigerant suction hose at Body	9.8	100	87 in.*lbf
Cooler refrigerant liquid pipe A at Cooler condenser assembly	5.4	55	47 in.*lbf
No. 1 cooler refrigerant discharge hose at Cooler condenser assembly	5.4	55	47 in.*lbf
No. 1 cooler refrigerant discharge hose at Compressor and magnetic clutch	9.8	100	87 in.*lbf
No. 1 cooler refrigerant suction hose at Compressor and magnetic clutch	9.8	100	87 in.*lbf
Cooler condenser assembly at Body	9.8	100	87 in.*lbf

REFRIGERANT LINE - TORQUE SPECIFICATIONS

AIR CONDITIONING AND BLOWER UNIT

Part tightened	N*m	Kgf*cm	Ft.*lbf
No. 1 cooler refrigerant suction hose at Air conditioning radiator assembly	9.8	100	87 in.*lbf
Air conditioning radiator assembly at Body	9.8	100	87 in.*lbf
Air conditioning tube assembly at Cooler expansion valve	4.1	42	36 in.*lbf

AIR CONDITIONING AND BLOWER UNIT - TORQUE SPECIFICATIONS

COMPRESSOR AND MAGNETIC CLUTCH

Part tightened		N*m	Kgf*cm	Ft.*lbf
No. 1 cooler refrigerant discharge hose at Compressor and magnetic clutch		9.8	100	7
No. 1 cooler refrigerant suction hose at Compressor and magnetic clutch		9.8	100	7
No. 1 compressor mounting bracket at Compressor and magnetic clutch	Nut	29	300	21
	Bolt	49	500	36

COMPRESSOR AND MAGNETIC CLUTCH - TORQUE SPECIFICATIONS

CONDENSER

Part tightened	N*m	Kgf*cm	Ft.*lbf
Cooler refrigerant liquid pipe A at Cooler condenser assembly	5.4	55	47 in.*lbf
Cooler refrigerant discharge hose at Cooler condenser assembly	5.4	55	47 in.*lbf
Radiator upper support at Body	9.8	100	7
Cooler condenser assembly at Body	9.8	100	7
Bracket at Cooler condenser assembly	5.4	55	47 in.*lbf
Cap at Cooler condenser assembly	12.3	125	9

CONDENSER - TORQUE SPECIFICATIONS

STEERING PAD

Part tightened	N*m	Kgf*cm	Ft.*lbf
Steering wheel assembly at Steering pad assembly	8.8	90	78 in.*lbf

STEERING PAD - TORQUE SPECIFICATIONS

SPIRAL CABLE

Part tightened	N*m	Kgf*cm	Ft.*lbf
Steering wheel assembly at Steering pad assembly	8.8	90	78 in.*lbf
Steering wheel assembly at Steering column assembly	50	510	37

SPIRAL CABLE - TORQUE SPECIFICATIONS

FRONT PASSENGER AIRBAG ASSEMBLY

Part tightened	N*m	Kgf*cm	Ft.*lbf
Front passenger airbag assembly at Instrument panel reinforcement	20	204	14

FRONT PASSENGER AIRBAG ASSEMBLY - TORQUE SPECIFICATIONS

CENTER AIRBAG SENSOR ASSEMBLY

Part tightened	N*m	Kgf*cm	Ft.*lbf
Center airbag sensor assembly at Body	20	204	14

CENTER AIRBAG SENSOR ASSEMBLY - TORQUE SPECIFICATIONS

FRONT AIRBAG SENSOR

Part tightened	N*m	Kgf*cm	Ft.*lbf
Front airbag sensor RH at Body	20	204	14
Front airbag sensor LH at Body	20	204	14

FRONT AIRBAG SENSOR - TORQUE SPECIFICATIONS

SIDE AIRBAG SENSOR

Part tightened	N*m	Kgf*cm	Ft.*lbf
Side airbag sensor assembly at Front door panel	20	204	14

SIDE AIRBAG SENSOR - TORQUE SPECIFICATIONS

REAR AIRBAG SENSOR

Part tightened	N*m	Kgf*cm	Ft.*lbf
Rear side airbag sensor at Body	20	204	14

REAR AIRBAG SENSOR - TORQUE SPECIFICATIONS

FRONT SEAT BELT

Part tightened	N*m	Kgf*cm	Ft.*lbf
Front seat inner belt assembly at Front seat	42	428	31
Front seat outer belt assembly (shoulder anchor) at Body	42	428	31
Front seat outer belt assembly (Upper part of retractor) at Body	7.5	77	66 in.*lbf
Front seat outer belt assembly (Lower part of retractor) at Body	42	428	31
Front seat outer belt assembly (floor anchor) at Body	42	428	31

FRONT SEAT BELT - TORQUE SPECIFICATIONS

REAR SEAT BELT

Part tightened	N*m	Kgf*cm	Ft.*lbf
Rear seat inner belt assembly at Front seat	42	428	31
Rear seat outer belt assembly (Upper part of retractor) at Body	7.5	77	66 in.*lbf
Rear seat outer belt assembly (Lower part of retractor) at Body	42	428	31
Rear seat outer belt assembly (floor anchor) at Body	42	428	31

REAR SEAT BELT - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Height control sensor sub-assembly front LH at Body	7.8	80	69 in.*lbf
Height control sensor sub-assembly front LH at Lower suspension arm	5.4	55	48 in.*lbf
Height control sensor sub-assembly front LH at Look nut	5.4	55	48 in.*lbf
Height control sensor sub-assembly rear LH at Body	7.8	80	69 in.*lbf
Height control sensor sub-assembly rear LH at Lower suspension arm	5.4	55	48 in.*lbf

LIGHTING - TORQUE SPECIFICATIONS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Windshield wiper motor assembly at Windshield wiper link assembly	5.4	55	48 in.*lbf
Windshield wiper motor assembly at Clank arm	17.2	175	13
Windshield wiper link assembly at Body	5.5	56	49 in.*lbf
Windshield wiper link assembly at Front wiper arm LH	25.5	260	18
Windshield wiper link assembly at Front wiper arm RH	25.5	260	18

WIPER AND WASHER - TORQUE SPECIFICATIONS

LOW PITCHED HORN

Part tightened	N*m	Kgf*cm	Ft.*lbf
Low pitched horn at Body	19	194	14

LOW PITCHED HORN - TORQUE SPECIFICATIONS

HIGH PITCHED HORN

Part tightened	N*m	Kgf*cm	Ft.*lbf
High pitched horn at Body	19	194	14

HIGH PITCHED HORN - TORQUE SPECIFICATIONS

WINDSHIELD/WINDOWGLASS

Part tightened	N*m	Kgf*cm	Ft.*lbf
Wiper arm at Body	22	224	16

WINDSHIELD/WINDOWGLASS - TORQUE SPECIFICATIONS

MIRROR

Part tightened	N*m	Kgf*cm	Ft.*lbf
Outer rear view mirror assembly at Door panel	5.5	56	49 in.*lbf

MIRROR - TORQUE SPECIFICATIONS

INSTRUMENT PANEL

Part tightened	N*m	Kgf*cm	Ft.*lbf
Steering column assembly at Instrument panel reinforcement	25	255	18
Front passenger airbag assembly at Instrument panel reinforcement	20	200	14
Steering wheel assembly at Steering column assembly	50	510	37

INSTRUMENT PANEL - TORQUE SPECIFICATIONS

FRONT SEAT

Part tightened	N*m	Kgf*cm	Ft.*lbf
Front seatback spring assembly at Front seat adjuster assembly	43.0	439	32
Front seat cushion spring assembly at Front seat adjuster assembly	21.0	214	15
Front seat inner belt assembly at Front seat adjuster assembly	42.0	428	31
Reclining remote control lever sub-assembly at Front seatback spring assembly	8.0	82	71 in.*lbf
Front seat assembly at Body	37.0	377	27

FRONT SEAT - TORQUE SPECIFICATIONS

REAR SEAT

Part tightened	N*m	Kgf*cm	Ft.*lbf
Wind deflector board assembly at Rear seat headrest assembly	5.0	51	43 in.*lbf
Rear seat headrest assembly at Body	5.0	51	43 in.*lbf
Rear seatback assembly at Body	18.0	184	13

REAR SEAT - TORQUE SPECIFICATIONS

Part tightened		N*m	Kgf*cm	Ft.*lbf
HOOD
Hood at Hood hinge		13	130	10
Hood lock at Body		8.0	82	71 in.*lbf
HOOD SUPPORT
Hood at Hood support		22	224	16
FRONT DOOR
Door hinge at Body		32.5	331	24
Door hinge at Door panel		32.5	331	24
Door lock striker at Body		23	235	17
Door lock at Door panel		5.5	56	48 in.*lbf
Window regulator at Door panel	Upper side	8.0	82	71 in.*lbf
Window regulator at Door panel	Lower side	13.0	133	10 ft.*lbf
Window regulator Motor at Door panel		5.5	56	48 in.*lbf
Door glass stopper at Door panel		11.5	117	8.5
LUGGAGE COMPARTMENT DOOR PANEL SUB-ASSEMBLY
Luggage compartment door panel sub-assembly at Luggage compartment door hinge assembly		22	224	16
Luggage compartment door striker assembly at Luggage compartment door panel sub-assembly		8.0	82	71 in.*lbf
LUGGAGE COMPARTMENT DOOR HINGE ASSEMBLY
Luggage compartment door panel sub-assembly at Luggage compartment door hinge assembly		22	224	16
Luggage compartment door support assembly at Body		22	224	16
Luggage compartment door support assembly at Luggage closer motor assembly		8.0	82	71 in.*lbf
Luggage compartment door support assembly at Luggage door closer assembly		5.0	51	44 in.*lbf
Luggage compartment door support assembly at Luggage door driver gear assembly		19	194	14
LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
Luggage control cable bracket set nut		5.5	56	49 in.*lbf

ENGINE HOOD / DOOR - TORQUE SPECIFICATIONS

FRONT BUMPER

Part tightened	N*m	Kgf*cm	Ft.*lbf
Front bumper reinforcement at Body	58	590	43

FRONT BUMPER - TORQUE SPECIFICATIONS

REMOVABLE ROOF PANEL

Part tightened	N*m	Kgf*cm	Ft.*lbf
Sliding roof drive gear sub-assembly at Removable roof lock sub-assembly	5.4	55	48 in.*lbf
Sliding roof removable roof panel sub-assembly at Roof panel link sub-assembly	40	408	30
Sliding roof removable roof panel sub-assembly at Removable roof lock sub-assembly	6.9	70	61 in.*lbf

REMOVABLE ROOF PANEL - TORQUE SPECIFICATIONS

BACK WINDOW FRAME

Part tightened	N*m	Kgf*cm	Ft.*lbf
Back window frame sub-assembly upper at Roof panel link sub-assembly	40	408	30

BACK WINDOW FRAME - TORQUE SPECIFICATIONS

ROOF PANEL LINK

Part tightened		N*m	Kgf*cm	Ft.*lbf
Sliding roof removable roof panel sub-assembly at Roof panel link sub-assembly		40	408	30
Rear seatback assembly at Body	Bolt	18	184	13
Rear seatback assembly at Body	Nut	7.0	71	63 in.*lbf
Back window frame sub-assembly upper at Roof panel link sub-assembly		40	408	30
Sliding roof drive gear assembly RH at Roof panel link sub-assembly		19	194	14

ROOF PANEL LINK - TORQUE SPECIFICATIONS

PACKAGE TRAY TRIM

Part tightened		N*m	Kgf*cm	Ft.*lbf
Rear seatback assembly at Body	Bolt	18	184	13
Rear seatback assembly at Body	Nut	7.0	71	63 in.*lbf

PACKAGE TRAY TRIM - TORQUE SPECIFICATIONS

REMOVABLE ROOF AUXILIARY CATCH

Part tightened	N*m	Kgf*cm	Ft.*lbf
Removable roof auxiliary catch assembly at Body	22	224	16

REMOVABLE ROOF AUXILIARY CATCH - TORQUE SPECIFICATIONS

Service Specifications: Specifications Lexus SC II рестайлинг

SPECIFIED TORQUE FOR STANDARD BOLTS

TORQUE SPECIFICATIONS

More articles — Service Specifications

Login / Signup

Enter the code

You have successfully logged in!