Introduction (General Information): Other Lexus RX III рестайлинг

CUSTOMIZE PARAMETERS [03/2012 - ]

Note. When the customer requests a change in a function, first make sure that the function can be customized. Be sure to make a note of the current settings before customizing. When troubleshooting a function, first make sure that the function is set to the default setting.

HINT

The following items can be customized.

1. POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM TILT & TELESCOPIC Display Default Content Setting Auto away/Return function ON Turn the auto away/return function ON/OFF ON / OFF
2. INTUITIVE PARKING ASSIST SYSTEM Customizing with the Techstream WARNING Display Default Content Setting Relevant ECU Fr Sensor Onset Range Wide Sets the detection operation range for the front center sensors. Narrow or Wide Narrow: 500 mm (19.7 in.) Wide: 1000 mm (39.4 in.) Clearance warning ECU assembly Rr Sensor Onset Range Wide Sets the detection operation range for the rear center sensors. Narrow or Wide Narrow: 600 mm (23.6 in.) Wide: 1500 mm (59.1 in.) Clearance warning ECU assembly Keep Sense Buzzer Avail Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds. Not Avail or Avail Not Avail: Not Available Avail: Available Clearance warning ECU assembly Fr & Rr Buzzer Volume M2 Changes the buzzer volume setting. L, M1, M2, M3 or H L: Low volume M1: Medium low volume M2: Medium volume M3: Medium high volume H: High volume Clearance warning ECU assembly SENSOR Display Default Content Setting Relevant ECU Sensor Condition N Avail Makes the front sensors available when the shift lever is in N. Not Avail or Avail Not Avail: Not Available Avail: Available Clearance warning ECU assembly Reverse Range Front Sensor Fcrn Changes the operation setting for the front sensors when the shift lever is in R. F, Fcrn or F Stop F: All front sensors are available Fcrn: Front corner sensors are available F Stop: All Front sensors are not available Clearance warning ECU assembly Non P/R Range Rear Sensor R Stop Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R. R, Rcrn or R Stop R: All rear sensors are available Rcrn: Rear corner sensors are available R Stop: All rear sensors are not available Clearance warning ECU assembly DISPLAY Display Default Content Setting Relevant ECU Display Mode*1 All The display mode setting (when the intuitive parking assist system is normal). All or Undisp Clearance warning ECU assembly *1: This item is used to allow or prevent the intuitive parking assist system from being displayed on the multi display assembly. For this model, some vehicles are not equipped with the multi display assembly. For those vehicles, the Display Mode item is not available. Customizing with Multi-display Turn the engine switch on (IG). Turn the intuitive parking assist system on. Enter the following menus: Setup / Vehicle / LEXUS park assist. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Alert volume 3 Sets the buzzer alert volume. 1, 2, 3, 4 or 5 1: Low volume 2: Medium low volume 3: Medium volume 4: Medium high volume 5: High volume Clearance warning ECU assembly Display On The display mode setting (when the intuitive parking assist system is normal). On or Off Clearance warning ECU assembly Distance FRONT Wide Sets the detection operation range for the front center sensors. Narrow or Wide Narrow: 500 mm (19.7 in.) Wide: 1000 mm (39.4 in.) Clearance warning ECU assembly Distance REAR Wide Sets the detection operation range for the rear center sensors. Narrow or Wide Narrow: 600 mm (23.6 in.) Wide: 1500 mm (59.1 in.) Clearance warning ECU assembly
3. POWER DOOR LOCK CONTROL SYSTEM Customizing with the Techstream DOOR LOCK Display Default Content Setting Unlock Key Twice ON Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors. ON or OFF Auto Lock ON*1 OFF*2 Function that locks all doors when the vehicle speed reaches a certain level. ON or OFF Auto Lock/Shift ON*2 OFF*1 Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed. ON or OFF Auto Unlock/Shift ON Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). ON or OFF All Unlock/Open-Close OFF Function that unlocks the other doors when the driver door is opened within approximately 45 seconds after the engine switch is turned off. ON or OFF *1: w/o Occupant Classification System *2: w/ Occupant Classification System ILLUMINATED ENTRY Display Default Content Setting Lighting Time 15 s Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the engine switch from off to on (ACC) or on (IG).) 7.5 s, 15 s or 30 s Customizing with Multi-display (w/ Navigation System or w/ Parking Assist Monitor System) Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Unlock on Second Key Turn On Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors. On or Off Main body ECU (Multiplex network body ECU) Auto Lock by Speed On*1 Off*2 Function that locks all doors when the vehicle speed reaches a certain level. On or Off Main body ECU (Multiplex network body ECU) Auto Lock by Shift from P On*2 Off*1 Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed. On or Off Main body ECU (Multiplex network body ECU) Auto Unlock by Shift to P On Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). On or Off Main body ECU (Multiplex network body ECU) Auto Unlock by Driver Door Off Function that unlocks the other doors when the driver door is opened within approximately 45 seconds after the engine switch is turned off. On or Off Main body ECU (Multiplex network body ECU) *1: w/o Occupant Classification System *2: w/ Occupant Classification System Customizing with Multi-display (w/o Navigation System without Parking Assist Monitor System) Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Auto Lock by Speed Off Function that locks all doors when the vehicle speed reaches a certain level. On or Off Main body ECU (Multiplex network body ECU) Auto Lock by Shift from P On Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed. On or Off Main body ECU (Multiplex network body ECU) Auto Unlock by Shift to P On Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). On or Off Main body ECU (Multiplex network body ECU) Auto Unlock by Driver Door Off Function that unlocks the other doors when the driver door is opened within approximately 45 seconds after the engine switch is turned off. On or Off Main body ECU (Multiplex network body ECU) Customizing using the Combination meter assembly Turn the engine switch on (IG). Press and hold the MENU switch on the steering pad switch assembly. Select the setting by referring to the table below Display Default Content Setting Relevant ECU SPEED SENSITIVE AUTO. LOCK ON*1 OFF*2 Function that locks all doors when the vehicle speed reaches a certain level. ON or OFF Main body ECU (Multiplex network body ECU) SHIFT-LINKED AUTOMATIC LOCK ON*2 OFF*1 Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed. ON or OFF Main body ECU (Multiplex network body ECU) SHIFT-LINKED AUTOMATIC UNLOCK ON Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). ON or OFF Main body ECU (Multiplex network body ECU) DRIVER DOOR-LINKED UNLOCK OFF Function that unlocks the other doors when the driver door is opened within approximately 45 seconds after the engine switch is turned off. ON or OFF Main body ECU (Multiplex network body ECU) *1: w/o Occupant Classification System *2: w/ Occupant Classification System Press the ENTER switch on the steering pad switch assembly. The setting completion screen will be displayed. Return to the item selection screen.
4. WIRELESS DOOR LOCK CONTROL SYSTEM Customizing with the Techstream WIRELESS DOOR LOCK Display (item) Default Function Setting Wireless Control ON Function that turns wireless door lock / ON or OFF ON or OFF Hazard Answer Back ON When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice. ON or OFF Open Door Warning ON The buzzer sounds when lock is pressed when any of the doors are ajar. ON or OFF Unlock 2 Operation ON Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. ON or OFF Panic Function ON Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds ON or OFF Auto Lock Time 60 s*1 or 30 s*2 Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s Wireless Auto Lock*1 ON This function turns the wireless auto lock function on or off. ON or OFF Wireless Buzzer Resp ON Wireless door lock buzzer response / ON or OFF ON or OFF P/W Ope buzzer ON Wireless power window buzzer response / ON or OFF ON or OFF Wireless Buzzer Vol Level 7 Wireless door lock buzzer Volume Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0 *1: except Mexico and Korea *2: for Mexico and Korea ILLUMINATED ENTRY Display Default Content Setting Lighting Time 15 s Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the engine switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s Customizing with Multi-display (w/ Navigation System or w/ Parking Assist Monitor System) Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Remote 2-Press Unlock On Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. On or Off Main body ECU (Multiplex network body ECU) Auto Relock Timer*1 60 s Function that regulates the interval between unlocking and automatic relocking of doors Off, 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU) Lock/Unlock Feedback-Lights On When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice. On or Off Main body ECU (Multiplex network body ECU) Lock/Unlock Feedback-Tone 7 Wireless door lock buzzer Volume Off, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU) *1: except Mexico and Korea Customizing with Multi-display (w/o Navigation System without Parking Assist Monitor System) Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Remote 2-Press Unlock On Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. On or Off Main body ECU (Multiplex network body ECU) Auto Relock Timer*1 60 s Function that regulates the interval between unlocking and automatic relocking of doors Off, 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU) Lock/Unlock Feedback-Lights On When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice. On or Off Main body ECU (Multiplex network body ECU) Lock/Unlock Feedback-Tone 7 Wireless door lock buzzer Volume Off, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU) *1: except Mexico Customizing using the Combination meter assembly Turn the engine switch on (IG). Press and hold the MENU switch on the steering pad switch assembly Select the setting by referring to the table below Display Default Content Setting Relevant ECU REMOTE 2-PRESS UNLOCK ON Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. ON or OFF Main body ECU (Multiplex network body ECU) AUTO. RELOCK TIME ADJUSTMENT*1 60 s Function that regulates the interval between unlocking and automatic relocking of doors OFF, 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU) LOCK/UNLOCK ANSWER BACK ON When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice. ON or OFF Main body ECU (Multiplex network body ECU) LOCK FEEDBACK VOLUME 7 Wireless door lock buzzer volume 0, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU) *1: except Mexico and Korea Press the ENTER switch on the steering pad switch assembly. The setting completion screen will be displayed. Return to the item selection screen.
5. SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function) Customizing with the Techstream SMART KEY/ACCESS Tester Display Default Content Setting Ignition Available Area All Function that switches the entry ignition detection area Front or All* Park Wait Time 2.5 s Function that sets waiting time to permit opening door after door is locked with entry lock function 0.5 s, 1.5 s, 2.5 s, or 5 s Back Door Opening Operation Long Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch) Long, Twice or OFF Door Unlock Mode Driver Function that chooses the doors to be operated by entry unlock operation All or Driver Touch Activation Over Threshold Active The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed. Active or Not Active *: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected. WARNING Tester Display Default Content Setting Key Low Battery Warning ON Function that warns driver that key battery is weak ON or OFF Customizing with Multi-display (w/ Navigation System or w/ Parking Assist Monitor System) Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Select Doors to Unlock Driver's Door Function that sets which doors are unlocked by the entry unlock function. All Doors or Driver's Door Certification ECU (smart key ECU assembly) Access System with Elec. Key On Function that enables or disables the smart access system with push-button start. On or Off Certification ECU (smart key ECU assembly) Customizing with Multi-display (w/o Navigation System without Parking Assist Monitor System) Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Select doors to unlock Driver's Door Function that sets which doors are unlocked by the entry unlock function. All Doors or Driver's Door Certification ECU (smart key ECU assembly) Access System with Elec. Key On Function that enables or disables the smart access system with push-button start. On or Off Certification ECU (smart key ECU assembly) Customizing using the Combination meter assembly Turn the engine switch on (IG). Press and hold the MENU switch on the steering pad switch assembly. Select the setting by referring to the table below Display Default Content Setting Relevant ECU SELECT DOORS TO UNLOCK DRIVER Function that chooses the doors to be operated by entry unlock operation ALL or DRIVER Certification ECU (smart key ECU assembly) ACCESS SYSTEM WITH ELEC. KEY ON Function that enables or disables the smart access system with push-button start. ON or OFF Certification ECU (smart key ECU assembly) Press the ENTER switch on the steering pad switch assembly. The setting completion screen will be displayed. Return to the item selection screen.
6. ENTRY UNLOCK MODE SWITCHING (SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function)) NOTE: Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode. Check that the power source mode is OFF and the LED on the key is not blinking. Press the lock switch and one of the other switches on the key at the same time for approximately 5 seconds while the key is in the detection area. Driver door unlock default setting: When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected. NOTE: After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again. Driver door unlock mode: When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock. All door unlock mode: When any touch sensor is touched, all doors unlock. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the smart access system with push-button start to the entry unlock mode. The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer assembly and combination meter assembly (buzzer) to inform the user that the mode has been changed. Mode Wireless Door Lock Buzzer Assembly Combination Meter Assembly (Buzzer) Driver Door (Default) Sounds 3 times Sounds once All Doors (Customized) Sounds 2 times Sounds once HINT: The procedure only changes the entry unlock mode of the smart access system with push-button start. It does not switch the unlocking of the wireless door lock control.
7. ELECTRICAL KEY CANCEL (SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function)) NOTE: Because the key (for card type) does not have a wireless transmitter function, it cannot be used to perform the key cancel operation. The electrical key cancel operation disables the following functions: Entry Unlock/Lock Entry Ignition Entry Back Door Open Electrical Key Lock-in Prevention Warning Memory Call The operation procedures are as follows: Precondition: Engine switch off, driver side door closed and unlocked. Push the unlock switch of the key once. Open the driver door within 5 seconds. Push the unlock switch of the key twice within 5 seconds. Close and open the driver door twice within 30 seconds. (Driver door: Close --> Open --> Close --> Open) Push the unlock switch of the key twice within 5 seconds. Close and open the driver door within 30 seconds. (Driver door: Close --> Open) Close the driver door within 5 seconds. When electrical key cancel is activated, the wireless door lock buzzer sounds twice. To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.
8. SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Start Function) Customizing with the Techstream SMART KEY/ACCESS Tester Display Default Content Setting Ignition Available Area All Function that switches the entry ignition detection area Front or All* *: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected. WARNING Tester Display Default Content Setting Key Low Battery Warning ON Function that warns driver that key battery is weak ON or OFF Customizing with Multi-display (w/ Navigation System or w/ Parking Assist Monitor System) Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Access System with Elec. Key On Function that enables or disables the smart access system with push-button start. On or Off Certification ECU (smart key ECU assembly) Customizing with Multi-display (w/o Navigation System without Parking Assist Monitor System) Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Access System with Elec. Key On Function that enables or disables the smart access system with push-button start. On or Off Certification ECU (smart key ECU assembly) Customizing using the Combination meter assembly Turn the engine switch on (IG). Press and hold the MENU switch on the steering pad switch assembly. Select the setting by referring to the table below Display Default Content Setting Relevant ECU ACCESS SYSTEM WITH ELEC. KEY ON Function that enables or disables the smart access system with push-button start. ON or OFF Certification ECU (smart key ECU assembly) Press the ENTER switch on the steering pad switch assembly. The setting completion screen will be displayed. Return to the item selection screen.
9. CUSTOMIZING FUNCTION WITHOUT TECHSTREAM (SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Start Function)) NOTE: Because the key (for card type) does not have a wireless transmitter function, it cannot be used to perform the key cancel operation. The electrical key cancel operation disables the following functions: Entry Unlock/Lock Entry Ignition Entry Back Door Open Electrical Key Lock-in Prevention Warning Memory Call The operation procedures are as follows: Precondition: Engine switch off, driver side door closed and unlocked. Push the unlock switch of the key once. Open the driver door within 5 seconds. Push the unlock switch of the key twice within 5 seconds. Close and open the driver door twice within 30 seconds. (Driver door: Close --> Open --> Close --> Open) Push the unlock switch of the key twice within 5 seconds. Close and open the driver door within 30 seconds. (Driver door: Close --> Open) Close the driver door within 5 seconds. When electrical key cancel is activated, the wireless door lock buzzer sounds twice. To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.
10. REMOTE ENGINE STARTER SYSTEM Display (Item) Default Content Setting Air Conditioner Mode User This function controls the air conditioner when the remote start function is operating. Auto/User Defogger Control OFF This function controls the window defogger operation when the remote start function is operating. ON/OFF
11. LIGHTING SYSTEM (LIGHTING INT) Customizing with the Techstream ILLUMINATED ENTRY Tester Display Default Content Setting Relevant ECU Lighting Time 15 s Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the engine switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s Main body ECU (Multiplex network body ECU) I/L when ACC OFF ON Lights up engine switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights when the engine switch is turned from on (ACC or IG) to off. ON or OFF I/L ON W/Door Key Unlock ON Lights up engine switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights when doors are unlocked using a mechanical key or door control transmitter. ON or OFF Room Light when Aprchd ON Lights up the engine switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights when a key enters any actuation area around the doors. ON or OFF Center Console Spot Light ON Lights up the center console spot light when engine switch is turned on (ACC or IG) ON or OFF Interior Light Control ON Change the interior lights (engine switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights) control. ON or OFF Customizing with Multi-display Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Lights Settings. Select the setting by referring to the table below: Display Default Content Setting Relevant ECU Interior Lights Off Timer 15 sec. Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the engine switch from off to on (ACC or IG).) Off, 7.5 sec., 15 sec., or 30 sec. Main body ECU (Multiplex network body ECU) Customizing using the Combination meter assembly Turn the engine switch on (IG). Press and hold the MENU switch on the steering pad switch assembly. Select the setting by referring to the table below: Display Default Content Setting Relevant ECU INTERIOR LIGHTS OFF TIME ADJUSTMENT 15 s Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the engine switch from off to on (ACC or IG).) Off, 7.5 s, 15 s, or 30 s Main body ECU (Multiplex network body ECU) Press the ENTER switch on the steering pad switch assembly. The setting completion screen will be displayed. Return to the item selection screen.
12. METER / GAUGE SYSTEM WARNING Tester Display Default Content Setting Driver Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer ON / OFF Front Passenger Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer ON / OFF *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more. *2: Although the item is displayed on the Techstream, the vehicle have not got the indicator, warning, buzzer, or display. DISPLAY Tester Display Default Content Setting ECO Drive Indicator ON Function to turn on or off the ECO driving indicator zone display in the multi-information display ON / OFF
13. FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) Customizing with the Techstream MAIN BODY Tester Display Default Content Setting Seat Move Distance Standard Allows customizing of the seat movement distance for the power easy access system. OFF / Little / Standard Customizing with Multi-display Turn the engine switch on (IG). Enter the following menus: Menu / Setup / Vehicle / Vehicle Settings / Vehicle Customization / Other Vehicle Settings Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Driver's Seat Easy Exit Full Allows customizing of the seat movement distance for the power easy access system. Full / Partial / Off Front power seat switch (driver side) Customizing using the Combination meter assembly Turn the engine switch on (IG). Press and hold the MENU switch on the steering pad switch assembly. Select the setting by referring to the table below Display Default Content Setting Relevant ECU DRIVER'S SEAT EASY EXIT FULL Allows customizing of the seat movement distance for the power easy access system. FULL / PARTIAL / OFF Front power seat switch (driver side) Press the ENTER switch on the steering pad switch assembly. The setting completion screen will be displayed. Return to the item selection screen.
14. SEAT BELT WARNING SYSTEM COMBINATION METER Tester Display Default Content Setting Driver Side Seatbelt Warning Buzzer ON Function to sound the seat belt warning buzzer ON / OFF Front Passenger Side Seatbelt Warning Buzzer ON Function to sound the seat belt warning buzzer ON / OFF HINT: This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.
15. AIR CONDITIONING SYSTEM Customizing with the Techstream AIR CONDITIONER Display (Item) Default Content Setting Set Temperature Shift Normal Function to control with the shifted temperature against the displayed temperature -2C, -1C, Normal, +1C, +2C Evaporator Control Automatic Function to set the evaporator control to the automatic position (AUTO) to save power, or to the coldest position (MANUAL) to dehumidify air and to prevent the windows from fogging up Automatic or Manual Air Inlet Mode*2 Automatic In case of turning the A/C on to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode Automatic or Manual Compressor Mode*3 Automatic Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off Automatic or Manual Foot/DEF Auto Mode ON Function to automatically turn the airflow to FOOT/DEF on when AUTO mode is on ON or OFF Foot/DEF Automatic Blow Up Function ON Function to automatically increase the blower level when the defroster is on ON or OFF Emission Gas Sensor Shift*1 Normal Function to change the sensitivity of the smog ventilation sensor Much Less, Less, Little Less, Normal, Little More, More, Much More ECO MODE Cancel OFF Function to cancel the ECO mode drive when item is on. OFF or ON *1: w/ Smog Ventilation Sensor *2: for Korea *3: except Korea Customizing with Multi-display Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Settings / Climate Settings. Select the setting by referring to the table below. Display Default Content Setting Relevant ECU Smog Sensor Sensitivity*1 0 Function to change the sensitivity of the smog ventilation sensor -3, -2, -1, 0, +1, +2, +3 Air conditioning amplifier assembly Auto A/C Mode*3 On Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off On or Off Air conditioning amplifier assembly Efficient Ventilation Mode*2 On In case of turning the A/C on to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode On or Off Air conditioning amplifier assembly *1: w/ Smog Ventilation Sensor *2: for Korea *3: except Korea
16. POWER WINDOW CONTROL SYSTEM POWER WINDOW Tester Display Default Content Setting Door Key P/W Up ON This function is used to close the windows by operating the mechanical key. ON/OFF Door Key P/W Down ON This function is used to open the windows by operating the mechanical key. ON/OFF P/W Down W/ Transmitter ON This function is used to open the windows using the wireless key transmitter. ON/OFF P Window Auto Up Avail This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger side). Avail/Not Avl P Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly. Avail/Not Avl RR Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH side). Avail/Not Avl RR Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly. Avail/Not Avl RL Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH side). Avail/Not Avl RL Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly. Avail/Not Avl
17. SLIDING ROOF SYSTEM SLIDING ROOF Tester Display Default Content Setting Door Key Related Open*1 ON Function to manually open sliding roof linked with power windows by holding driver side door key for 1.5 seconds or more to unlock position when engine switch is off ON / OFF Door Key Related Close*1 ON Function to manually close sliding roof linked with power windows by holding driver side door key for 1.5 seconds or more to lock position when engine switch is off ON / OFF Wireless Key Related Open*2 ON Function to manually open sliding roof linked with power windows by pressing transmitter UNLOCK switch for 2.5 seconds or more when engine switch is off ON / OFF Door Key Related Operation Slide Function to select tilt up or slide open of manual sliding roof operation linked with power windows by holding driver side door key for 1.5 seconds or more to unlock position when engine switch is off Tilt / Slide Wireless Key Related Operation Slide Function to select tilt up or slide open of manual sliding roof operation linked with power windows by pressing on transmitter UNLOCK switch for 2.5 seconds or more when engine switch is off Tilt / Slide *1: This function is linked with the power window key-linked function. If the power window key-linked function is set to OFF, the sliding roof key-linked function will not operate even when it is set to ON. *2: This function is linked with the power window wireless transmitter-linked function. If the power window wireless transmitter-linked function is set to OFF, the sliding roof wireless transmitter-linked function will not operate even when it is set to ON.
18. POWER BACK DOOR SYSTEM PSD&PBD OPERATION Tester Display Default Content Setting PBD SW Operation 0.8 s Function that turns the power back door closer switch on when a switch is pushed once or held down for 0.8 seconds. 0.8 s or 0.0 s PBD Buzzer*1 OFF Function that makes the power back door buzzer sound when the power back door is operating. OFF or ON Door unlock with 1 motion Back Door Function that selects the door or doors to unlock when the back door is locked and the transmitter switch is pushed to operate the power back door. Back Door or ALL DOORS One Motion (Not Use)*2 Function that operates the power back door by pushing the transmitter switch when the back door is unlocked. OFF, 1 Op, 2 Op or 0.8 s One Motion with unlock door 0.8 s Function that operates the power back door by pushing the transmitter switch regardless of the door lock condition. OFF, 2 Op or 0.8 s PBD Assist Open Operation*3, 4 OFF Function that enables or disables the power back door assist open operation. When PBD Assist Open is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated. OFF or ON *1: The warning buzzer that sounds when the power back door is operating cannot be customized (even if this function is set to "OFF", the buzzer will still sound). *2: "Not Use" is not a setting that can be selected. HINT: When either "One Motion" or "One Motion with unlock door" is selected, the other will display "Not Use". *3: The power back door assist operation will be linked with the "Back Door Opening Operation" setting of the smart access system with push-button start (for entry function) only when all doors are locked. If "Back Door Opening Operation" is set to "OFF", the power back door assist will not operate even if "PBD Assist Open Operation" is set to "ON". Refer to «CUSTOMIZE PARAMETERS [03/2012 - ]»(ref-602557-S37926127862014030500000) *4: for models with the "PBD Assist Open Operation" customize setting item.
19. LIGHTING SYSTEM (LIGHTING EXT) Customizing with the Techstream LIGHT CONTROL Display Default Content Setting Relevant ECU Disp Ex ON Sen NORMAL Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*A LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2 Main Body ECU (Multiplex Network Body ECU) Disp Ex OFF Sen NORMAL Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2 Light Auto OFF Delay 30 s Keeps the headlights on for a certain period of time after turning the engine switch off and closing all the doors with the low beam headlights on. OFF, 30 s, 60 s or 90 s Sensitivity Normal Adjusts the sensitivity of the automatic light control system.*C Light2, Light1, Normal, Dark1 or Dark2 DRL Function ON ON/OFF of the DRL function ON or OFF Light up Clearance Lights at Door Unlock Function ON This function turns on the parking lights and taillights for 15 seconds when the doors are unlocked by the smart key or the wireless key. ON or OFF HINT: The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle. *A Brightness level required to dim the lights Setting DARK2 DARK1 NORMAL LIGHT1 LIGHT2 *B Brightness level required to cancel the dimming of the lights Setting DARK2 DARK1 NORMAL LIGHT1 LIGHT2 *C Sensitivity of the automatic light control system Setting Dark2 Dark1 Normal Light1 Light2 ILLUMINATED ENTRY Display Default Content Setting Relevant ECU Mirr-Foot-Lgt Approached ON Lights up the door mirror foot lights when a key enters any actuation area around the doors. ON or OFF Main Body ECU (Multiplex Network Body ECU) Mirr-Foot-Lgt Unlocked ON Lights up door mirror foot lights when doors are unlocked using a mechanical key or door control transmitter. ON or OFF Mirror Foot Lighting Time 15 s Changes the lighting time of the door mirror foot lights. 7.5 s, 15 s, 30 s or 0 s Exterior Light Control ON Changes the door mirror foot light control. ON or OFF Customizing with Multi-display Turn the engine switch on (IG). Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Light Settings. Select the setting by referring to the table below. LIGHT SETTINGS Display Default Content Setting Relevant ECU Headlamps-On Sensitivity 0 Adjusts the sensitivity of the automatic light control system.*A -2, -1, 0, +1 or +2 Main Body ECU (Multiplex Network Body ECU) Headlamps Auto-Off Timer 30 sec. Keeps the headlights on for a certain period of time after turning the engine switch off and closing all doors with the low beam headlights on. Off, 30 sec., 60 sec. or 90 sec. Daytime Running Lights On ON/OFF of the DRL function On or Off Exterior Lights Off Timer 15 sec. Changes the lighting time of the door mirror foot lights. Off, 7.5 sec., 15 sec. or 30 sec. HINT: The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle. *A Sensitivity of the automatic light control system Setting -2 -1 0 +1 +2 Customizing using the Combination meter assembly Turn the engine switch on (IG). Press and hold the MENU switch on the steering pad switch assembly. Select the setting by referring to the table below: Display Default Content Setting Relevant ECU LIGHT SENSOR SENSITIVITY 0 Adjusts the sensitivity of the automatic light control system.*A -2, -1, 0, +1 or +2 Main Body ECU (Multiplex Network Body ECU) HEADLIGHT OFF TIME ADJUSTMENT 30 s Keeps the headlights on for a certain period of time after turning the engine switch off and closing all doors with the low beam headlights on. OFF, 30 s, 60 s or 90 s DAYTIME RUNNING LIGHTS ON ON/OFF of the DRL function ON or OFF EXTERIOR LIGHTS OFF TIME ADJUSTMENT 15 s Changes the lighting time of the door mirror foot lights. OFF, 7.5 s, 15 s or 30 s HINT: The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle. *A Sensitivity of the automatic light control system Setting -2 -1 0 +1 +2 Press the ENTER switch on the steering pad switch assembly. The setting completion screen will be displayed. Return to the item selection screen.

INITIALIZATION [03/2012 - 07/2012]

1. PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED Necessary Procedures Effect / Inoperative Function When Necessary Procedures are not Performed Refer to Reset back door close position Power back door function Back door closer function Refer to «INITIALIZATION [03/2012 - ]»(ref-602558-S11668731092014030500000) Correct the steering angle neutral point Parking assist monitor system Refer to «INITIALIZATION [03/2012 - ]»(ref-602559-S30982920972014030500000) NOTE: After the engine switch is turned off, the multi-media module receiver assembly (w/ Navigation System or w/ Parking Assist Monitor System) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.
2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED Replacement Part Necessary Procedure Effect / Inoperative Function when Necessary Procedures are not Performed Refer to ECM Vehicle Identification Number (VIN) registration MIL comes on Refer to «REGISTRATION [03/2012 - ]»(ref-602560-S26315024432014030500000) ECU communication ID registration (Engine immobiliser system) Engine start Refer to «REGISTRATION [03/2012 - ]»(ref-602561-S11508190522014030500000) Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly (Dynamic radar cruise control system) Dynamic radar cruise control system Pre-collision system Refer to «ADJUSTMENT [03/2012 - ]»(ref-602562-S10556630812014030500000) Automatic transaxle assembly Reset memory Input transaxle compensation code into TCM Perform road test to allow TCM to Learn Large shift shock The deterioration of fuel efficiency Refer to «INITIALIZATION [03/2012 - ]»(ref-602563-S09744920352014030500000) for U660E Initialization Refer to «REGISTRATION [03/2012 - ]»(ref-602563-S13160861212014030500000) for U660E Registration Refer to «INITIALIZATION [03/2012 - ]»(ref-602564-S02539185132014030500000) for U660F Initialization Refer to «REGISTRATION [03/2012 - ]»(ref-602564-S36675098982014030500000) for U660F Registration Valve body assembly Shift solenoid valve SL3 and/or SL4 Reset memory Reset transaxle compensation code Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency Shift solenoid valve SL1 and/or SL2 Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency TCM (If possible, read the transaxle compensation code from the previous TCM) Possible Reset memory Transfer transaxle compensation code Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency Impossible Reset memory Reset transaxle compensation code Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency Tire pressure warning ECU Tire pressure warning valve and transmitter Code registration (Tire pressure warning system) When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates. Tire pressure warning function Refer to «REGISTRATION [03/2012 - ]»(ref-602565-S38902899122014030500000) Brake actuator assembly (Skid control ECU) Perform yaw rate and acceleration sensor zero point calibration and store system information ABS warning light illumination Slip indicator light illumination VSC disabled or malfunctioning Refer to «CALIBRATION [03/2012 - ]»(ref-602555-S22584671462014030500000) Yaw rate and acceleration sensor Clear the zero point calibration data and system information Perform yaw rate and acceleration sensor zero point calibration and store system information Power steering ECU Rotation angle sensor initialization and torque sensor zero point calibration P/S warning light comes on EPS control Refer to «CALIBRATION [03/2012 - ]»(ref-602566-S35786595422014030500000) Steering column assembly Rotation angle sensor initialization and torque sensor zero point calibration Steering effort is different between turning steering wheel to left and right Spiral with sensor cable sub-assembly Correct steering angle neutral point Steering angle setting Parking assist monitor system Refer to «INITIALIZATION [03/2012 - ]»(ref-602559-S30982920972014030500000) for Initialization Refer to «CALIBRATION [03/2012 - ]»(ref-602559-S36923938072014030500000) for Calibration Multi-media module receiver assembly Parking assist monitor system initialization Parking assist monitor system Refer to «CALIBRATION [03/2012 - ]»(ref-602559-S36923938072014030500000) Rear television camera assembly Back camera position setting Parking assist monitor system Inner rear view mirror assembly*1 Re-registration of codes in the garage door opener system Register transmitter code Garage door opener system Refer to «REGISTRATION [03/2012 - ]»(ref-602567-S40192760102014030500000) DCM (Telematics Transceiver) DCM activation Safety connect system Refer to «DCM ACTIVATION [03/2012 - ]»(ref-602568-S31924659552014030500000) Certification ECU (smart key ECU assembly) ID code box (immobiliser code ECU) Steering lock ECU (steering lock actuator assembly) Key Code registration (Engine immobiliser system) Wireless door lock control system Smart access system with push-button start Engine start Refer to «REGISTRATION [03/2012 - ]»(ref-602561-S11508190522014030500000) Remote engine starter ECU assembly *2 Code registration (Engine immobiliser system) Remote engine start Occupant classification ECU Front passenger seat Zero point calibration (Occupant classification system) Sensitivity check (Occupant classification system) Occupant classification system Passenger airbag ON/OFF indicator Airbag system (Front passenger side) Seat belt warning system (Front passenger side) Refer to «INITIALIZATION [03/2012 - ]»(ref-602569-S05128513522014030500000) Power window regulator motor Door window regulator Initialize power window control system Automatic door glass open/ close function Jam protection function Operation function after engine switch is turned off Key-linked operation function Wireless transmitter-linked operation Refer to «INITIALIZATION [03/2012 - ]»(ref-602570-S16724986282014030500000) Sliding roof ECU (sliding roof drive gear sub-assembly) Sliding roof glass Sliding roof housing Initialize sliding roof ECU (pulse sensor initial position setting) Automatic slide open/close and tilt up/down function of sliding roof Jam protection function Operation function after engine switch is turned off Key-linked operation function Wireless transmitter-linked operation Refer to «INITIALIZATION [03/2012 - ]»(ref-602571-S15172327232014030500000) AFS ECU (headlight swivel ECU assembly) Perform AFS ECU (headlight swivel ECU assembly) initialization Headlight leveling function Refer to «INITIALIZATION [03/2012 - 07/2012]»(ref-602572-S10538147802014030500000) Rear height control sensor sub-assembly RH Perform AFS ECU (headlight swivel ECU assembly) initialization Headlight leveling function *1: w/ Garage Door Opener System *2: w/ Remote Engine Starter System

INITIALIZATION [07/2012 - ]

1. PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED Necessary Procedures Effect / Inoperative Function When Necessary Procedures are not Performed Refer to Reset back door close position Power back door function Back door closer function Refer to «INITIALIZATION [03/2012 - ]»(ref-602558-S11668731092014030500000) Correct the steering angle neutral point Parking assist monitor system Refer to «INITIALIZATION [03/2012 - ]»(ref-602559-S30982920972014030500000) NOTE: After the engine switch is turned off, the multi-media module receiver assembly (w/ Navigation System or w/ Parking Assist Monitor System) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.
2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED Replacement Part Necessary Procedure Effect / Inoperative Function when Necessary Procedures are not Performed Refer to ECM Vehicle Identification Number (VIN) registration MIL comes on Refer to «REGISTRATION [03/2012 - ]»(ref-602560-S26315024432014030500000) ECU communication ID registration (Engine immobiliser system) Engine start Refer to «REGISTRATION [03/2012 - ]»(ref-602561-S11508190522014030500000) Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly (Dynamic radar cruise control system) Dynamic radar cruise control system Pre-collision system Refer to «ADJUSTMENT [03/2012 - ]»(ref-602562-S10556630812014030500000) Automatic transaxle assembly Reset memory Input transaxle compensation code into TCM Perform road test to allow TCM to Learn Large shift shock The deterioration of fuel efficiency Refer to «INITIALIZATION [03/2012 - ]»(ref-602563-S09744920352014030500000) for U660E Initialization Refer to «REGISTRATION [03/2012 - ]»(ref-602563-S13160861212014030500000) for U660E Registration Refer to «INITIALIZATION [03/2012 - ]»(ref-602564-S02539185132014030500000) for U660F Initialization Refer to «REGISTRATION [03/2012 - ]»(ref-602564-S36675098982014030500000) for U660F Registration Valve body assembly Shift solenoid valve SL3 and/or SL4 Reset memory Reset transaxle compensation code Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency Shift solenoid valve SL1 and/or SL2 Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency TCM (If possible, read the transaxle compensation code from the previous TCM) Possible Reset memory Transfer transaxle compensation code Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency Impossible Reset memory Reset transaxle compensation code Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency Automatic transaxle assembly Reset memory Input transaxle compensation code into TCM Perform road test to allow TCM to Learn Large shift shock The deterioration of fuel efficiency Refer to «INITIALIZATION [07/2012 - ]»(ref-602573-S18429846892014030500000) for U880F Initialization Refer to «REGISTRATION [07/2012 - ]»(ref-602573-S20946371132014030500000) for U880F Registration ECM Engine Reset memory Perform road test to allow TCM to Learn Large shift shock The deterioration of fuel efficiency Valve body assembly Shift solenoid valve SL3, SL4 and/or SL5 Reset transaxle compensation code Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency Shift solenoid valve SL1 and/or SL2 Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency TCM (If possible, read the transaxle compensation code from the previous TCM) Possible Transfer transaxle compensation code Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency Impossible Reset transaxle compensation code Set the transaxle compensation code Perform road test to allow TCM to learn Large shift shock The deterioration of fuel efficiency Tire pressure warning ECU Tire pressure warning valve and transmitter Code registration (Tire pressure warning system) When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates. Tire pressure warning function Refer to «REGISTRATION [03/2012 - ]»(ref-602565-S38902899122014030500000) Brake actuator assembly (Skid control ECU) Perform yaw rate and acceleration sensor zero point calibration and store system information ABS warning light illumination Slip indicator light illumination VSC disabled or malfunctioning Refer to «CALIBRATION [03/2012 - ]»(ref-602555-S22584671462014030500000) Yaw rate and acceleration sensor Clear the zero point calibration data and system information Perform yaw rate and acceleration sensor zero point calibration and store system information Power steering ECU Rotation angle sensor initialization and torque sensor zero point calibration P/S warning light comes on EPS control Refer to «CALIBRATION [03/2012 - ]»(ref-602566-S35786595422014030500000) Steering column assembly Rotation angle sensor initialization and torque sensor zero point calibration Steering effort is different between turning steering wheel to left and right Spiral with sensor cable sub-assembly Correct steering angle neutral point Steering angle setting Parking assist monitor system Refer to «INITIALIZATION [03/2012 - ]»(ref-602559-S30982920972014030500000) for Initialization Refer to «CALIBRATION [03/2012 - ]»(ref-602559-S36923938072014030500000) for Calibration Multi-media module receiver assembly Parking assist monitor system initialization Parking assist monitor system Refer to «CALIBRATION [03/2012 - ]»(ref-602559-S36923938072014030500000) Rear television camera assembly Back camera position setting Parking assist monitor system Inner rear view mirror assembly*1 Re-registration of codes in the garage door opener system Register transmitter code Garage door opener system Refer to «REGISTRATION [03/2012 - ]»(ref-602567-S40192760102014030500000) DCM (Telematics Transceiver) DCM activation Safety connect system Refer to «DCM ACTIVATION [03/2012 - ]»(ref-602568-S31924659552014030500000) Certification ECU (smart key ECU assembly) ID code box (immobiliser code ECU) Steering lock ECU (steering lock actuator assembly) Key Code registration (Engine immobiliser system) Wireless door lock control system Smart access system with push-button start Engine start Refer to «REGISTRATION [03/2012 - ]»(ref-602561-S11508190522014030500000) Remote engine starter ECU assembly *2 Code registration (Engine immobiliser system) Remote engine start Occupant classification ECU Front passenger seat Zero point calibration (Occupant classification system) Sensitivity check (Occupant classification system) Occupant classification system Passenger airbag ON/OFF indicator Airbag system (Front passenger side) Seat belt warning system (Front passenger side) Refer to «INITIALIZATION [03/2012 - ]»(ref-602569-S05128513522014030500000) Power window regulator motor Door window regulator Initialize power window control system Automatic door glass open/ close function Jam protection function Operation function after engine switch is turned off Key-linked operation function Wireless transmitter-linked operation Refer to «INITIALIZATION [03/2012 - ]»(ref-602570-S16724986282014030500000) Sliding roof ECU (sliding roof drive gear sub-assembly) Sliding roof glass Sliding roof housing Initialize sliding roof ECU (pulse sensor initial position setting) Automatic slide open/close and tilt up/down function of sliding roof Jam protection function Operation function after engine switch is turned off Key-linked operation function Wireless transmitter-linked operation Refer to «INITIALIZATION [03/2012 - ]»(ref-602571-S15172327232014030500000) AFS ECU (headlight swivel ECU assembly) Perform AFS ECU (headlight swivel ECU assembly) initialization Headlight leveling function Refer to «INITIALIZATION [07/2012 - ]»(ref-602572-S03490169582014030500000) Rear height control sensor sub-assembly RH Perform AFS ECU (headlight swivel ECU assembly) initialization Headlight leveling function *1: w/ Garage Door Opener System *2: w/ Remote Engine Starter System

GLOSSARY OF SAE AND LEXUS TERMS [03/2012 - ]

This glossary lists all SAE-J1930 terms and abbreviations used in this manual in compliance with SAE recommendations, as well as their LEXUS equivalents.