TORQUE SPECIFICATIONS
| Part Tightened | N*m | Kgf*cm | Ft.*lbf | |
|---|---|---|---|---|
| No. 1 air cleaner inlet x Radiator support upper | 5.0 | 51 | 44 in.*lbf | |
DRIVE BELT
| Part Tightened | N*m | Kgf*cm | Ft.*lbf | |
|---|---|---|---|---|
| Air cleaner case x Body | 5.0 | 51 | 44 in.*lbf | |
| No. 1 air cleaner inlet x Radiator support upper | 5.0 | 51 | 44 in.*lbf | |
| No. 2 ground wire x Body | Body side | 9.0 | 92 | 80 in.*lbf |
| Engine side | 10 | 102 | 7 | |
| Front suspension member protector lower x Front suspension crossmember sub-assembly | 8.0 | 82 | 71 in.*lbf | |
| Front suspension crossmember sub-assembly x Body (for 2WD) | For nut A | 167 | 1703 | 123 |
| For bolt B | 204 | 2080 | 150 | |
| For bolt C | 50 | 510 | 37 | |
| For bolt D | 49 | 500 | 36 | |
| Front suspension crossmember sub-assembly x Body (for 4WD) | For nut A | 167 | 1703 | 123 |
| For bolt B | 165 | 1683 | 122 | |
| For bolt C | 50 | 510 | 37 | |
| Engine rear mounting member x Body | 26 | 265 | 19 | |
| Drive plate and ring gear sub-assembly x Engine assembly | 83 | 850 | 61 | |
| Engine coolant temperature sensor x Rear water by-pass joint | 20 | 204 | 15 | |
| Oil pressure switch x Oil filer bracket | 15 | 153 | 11 | |
| Engine oil level sensor x Oil pan | 7.0 | 71 | 62 in.*lbf | |
| Ignition coil x Cylinder head cover | 10 | 102 | 7 | |
| V-bank cover bracket x Cylinder head cover | 10 | 102 | 7 | |
| Radio setting condenser x Cylinder head cover | 10 | 102 | 7 | |
| Fuel tube sub-assembly x Cylinder head cover | 10 | 102 | 7 | |
| Water hose joint x Cylinder head cover | 10 | 102 | 7 | |
| No. 2 surge tank stay x Cylinder head | 21 | 214 | 15 | |
| V-ribbed belt tensioner x Cylinder block (for 2WD and 4WD) | 43 | 438 | 32 | |
| No. 2 idler pulley x Cylinder block | 54 | 550 | 40 | |
| Injector driver x Timing chain cover | 10 | 102 | 7 | |
| Engine mounting bracket LH and RH x Cylinder block (for 2WD and 4WD) | 43 | 438 | 32 | |
| Engine mounting insulator LH and RH x Engine mounting bracket LH and RH (for 2WD and 4WD) | For bolt | 35 | 357 | 26 |
| For nut | 70 | 714 | 52 | |
| No. 1 engine hanger x Cylinder head | 33 | 336 | 24 | |
| Exhaust manifold LH and RH x Cylinder head | 21 | 214 | 15 | |
| Oil dipstick guide x Cylinder block (for 2WD and 4WD) | 10 | 102 | 7 | |
| No. 2 oil dipstick guide x Cylinder head (for 2WD and 4WD) | 21 | 214 | 15 | |
| Steering sliding yoke sub-assembly x No. 2 intermediate shaft and steering sliding yoke (for 2WD) | 35 | 357 | 26 | |
| No. 2 steering intermediate shaft assembly x Steering main shaft and steering gear's shaft (for 4WD) | 35 | 357 | 26 | |
| Engine under cover air guide bracket x Body (for 2WD) | 26 | 265 | 19 | |
| No. 4 relay block x Body | 13 | 133 | 10 | |
| ECM cover x ECM box | 5.5 | 56 | 49 | |
| Ground cable x Cylinder block | 21 | 214 | 15 | |
ENGINE ASSEMBLY
| Part Tightened | N*m | Kgf*cm | Ft.*lbf | |
|---|---|---|---|---|
| Cylinder block stud bolt | 10 | 102 | 7 | |
| Cylinder head stud bolt | For stud bolt A, B and C | 10 | 102 | 7 |
| For stud bolt D | 4.0 | 41 | 35 | |
| No. 1 oil nozzle sub-assembly x Cylinder block | 9.0 | 92 | 80 in.*lbf | |
| Water drain cock LH and RH x Cylinder block | 30 | 306 | 22 | |
| Water drain cock plug LH and RH x Cylinder block | 13 | 130 | 9 | |
| Crankshaft bearing cap x Cylinder block | 1st for 16 point head | 61 | 622 | 45 |
| 2nd for 16 point head | Turn 90° | Turn 90° | Turn 90° | |
| For 12 mm head | 26 | 265 | 19 | |
| Connecting rod cap x Connecting rod sub-assembly | 1st | 40 | 408 | 30 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Crankshaft position sensor x Cylinder block | 10 | 102 | 7 | |
| No. 2 straight screw plug x Cylinder head | 80 | 816 | 59 | |
| No. 2 straight screw plug x Cylinder head | 44 | 449 | 32 | |
| Water outlet pipe sub-assembly x Cylinder block | 10 | 102 | 7 | |
| Cylinder head sub-assembly x Cylinder block (for bank 1 and 2) | 1st | 36 | 367 | 27 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| 3rd | Turn 90° | Turn 90° | Turn 90° | |
| For 14 mm head | 30 | 306 | 22 | |
| Camshaft bearing cap x Cylinder head (for bank 1 and 2) | 10 | 102 | 7 | |
| Camshaft housing sub-assembly x Cylinder head (for bank 1 and 2) | 28 | 286 | 21 | |
| No. 2 chain tensioner assembly x Cylinder head | 21 | 214 | 15 | |
| Camshaft timing gear x Camshaft | 100 | 1020 | 74 | |
| No. 3 chain tensioner x Cylinder head | 21 | 214 | 15 | |
| No. 1 chain vibration damper x Cylinder head and cylinder block | 23 | 235 | 17 | |
| Idle sprocket assembly x Cylinder block | 60 | 612 | 44 | |
| No. 1 chain tensioner assembly x Cylinder head | 10 | 102 | 7 | |
| Crankshaft pulley x Crankshaft | 250 | 2549 | 184 | |
| Oil strainer sub-assembly x Cylinder block (for 2WD and 4WD) | 10 | 102 | 7 | |
| Oil pan baffle plate x Cylinder block | 10 | 102 | 7 | |
| Oil pan sub-assembly x Cylinder block (for 2WD and 4WD) | For bolt A | 10 | 102 | 7 |
| For bolt except A | 21 | 214 | 15 | |
| Oil strainer pipe sub-assembly x Oil pan sub-assembly (for 4WD) | 10 | 102 | 7 | |
| No. 2 oil pan sub-assembly x Oil pan sub-assembly (for 2WD and 4WD) | 10 | 102 | 7 | |
| Oil pan drain plug x No. 2 oil pan sub-assembly (for 2WD and 4WD) | 40 | 408 | 30 | |
| Cylinder head cover sub-assembly x Cylinder head (for Bank 1 and 2) | For bolt A | 21 | 214 | 15 |
| For bolt except A | 10 | 102 | 7 | |
| Rear water by-pass joint x Cylinder head | 10 | 102 | 7 | |
| Water inlet with thermostat sub-assembly x Water inlet | 10 | 102 | 7 | |
| Water inlet x Chain cover | 10 | 102 | 7 | |
| No. 1 oil pipe x Cylinder head cover and cylinder head (for Bank 1 and 2) | 60 | 612 | 44 | |
| No. 1 oil pipe x Cylinder head cover and cylinder head (for Bank 1 and 2) | 60 | 612 | 44 | |
| Camshaft timing oil control valve x Cylinder head cover | 10 | 102 | 7 | |
| VVT sensor x Cylinder head cover | 10 | 102 | 7 | |
| Ventilation valve sub-assembly x Cylinder head cover | 27 | 275 | 18 | |
| Spark plug x Cylinder head | 18 | 184 | 13 | |
ENGINE UNIT