TORQUE SPECIFICATIONS
| Part Tightened | N*m | Kgf*cm | Ft.*lbf | |
|---|---|---|---|---|
| No. 1 air cleaner inlet x Engine assembly | 5.0 | 51 | 44 in.*lbf | |
DRIVE BELT
| Part Tightened | N*m | Kgf*cm | Ft.*lbf | |
|---|---|---|---|---|
| Air cleaner cap with air cleaner hose x Throttle body | 4.0 | 41 | 35 in.*lbf | |
| Air cleaner case x Body | 5.0 | 51 | 44 in.*lbf | |
| No. 1 air cleaner inlet x Body | 5.0 | 51 | 44 in.*lbf | |
| No. 2 ground wire x Body | Body side | 8.0 | 82 | 70 in.*lbf |
| Engine side | 10 | 102 | 7 | |
| No. 3 ground wire x Body | 8.5 | 87 | 75 in.*lbf | |
| Oil pump motor controller x Body | 5.0 | 51 | 44 in.*lbf | |
| No. 1 cooler refrigerant suction hose x Cooler compressor | 9.8 | 100 | 7 | |
| Front exhaust pipe assembly x exhaust manifold | 62 | 632 | 46 | |
| Exhaust pipe No. 1 support bracket sub-assembly x exhaust manifold | For Nut | 62 | 632 | 46 |
| For Bolt | 43 | 438 | 22 | |
| Front No. 1 floor heat insulator x Body | 5.0 | 51 | 44 in.*lbf | |
| Front No. 3 floor heat insulator x Body | 5.5 | 56 | 49 in.*lbf | |
| Front No. 4 floor heat insulator x Body | 5.5 | 56 | 49 in.*lbf | |
| Front No. 5 floor heat insulator x Body | 5.0 | 51 | 44 in.*lbf | |
| Front No. 6 floor heat insulator x Body | 5.0 | 51 | 44 in.*lbf | |
| Front floor brace center x Body | 7.4 | 75 | 65 in.*lbf | |
| Rear floor No. 1 panel brace x Body | 19 | 195 | 14 | |
| Front axle assembly x Suspension arm | 120 | 1224 | 89 | |
| Front suspension member protector lower x Front suspension crossmember sub-assembly | 8.0 | 82 | 71 in.*lbf | |
| Front suspension crossmember sub-assembly x Body | For bolt A | 167 | 1,700 | 123 |
| Front suspension crossmember sub-assembly x Body | For bolt B | 204 | 2,080 | 150 |
| Front suspension crossmember sub-assembly x Body | For bolt C | 50 | 510 | 37 |
| Front suspension crossmember sub-assembly x Body | For bolt D | 49 | 500 | 36 |
| Flywheel sub-assembly x Engine assembly | 83 | 850 | 61 | |
| Transmission input damper cover x Flywheel sub-assembly | 49 | 504 | 36 | |
| Engine mount bracket x Body | 35 | 357 | 26 | |
| Front stabilizer bar x Body | 49 | 500 | 36 | |
| No. 1 oil dipstick guide x Engine | 10 | 102 | 7 | |
| No. 2 oil dipstick guide x Engine | 21 | 214 | 15 | |
| Electric inverter compressor x Engine | 25 | 255 | 18 | |
| Intake manifold x Engine assembly | 21 | 214 | 15 | |
| Intake air surge tank x Engine assembly | For bolt | 18 | 184 | 13 |
| For nut | 16 | 163 | 12 | |
| No. 2 surge tank bracket x Intake air surge tank | 21 | 214 | 15 | |
| No. 3 water bypass hose pipe x Intake air surge tank | 10 | 102 | 7 | |
| High pressure side fuel pump x Cylinder head cover | 25 | 255 | 18 | |
| No. 1 fuel pipe x Cylinder head cover | 10 | 102 | 7 | |
| No. 2 fuel pipe x Fuel delivery pipe | 10 | 102 | 7 | |
| No. 3 fuel pipe x Fuel delivery pipe | 10 | 102 | 7 | |
| Fuel delivery pipe x Cylinder head sub-assembly | 21 | 214 | 15 | |
| Knock sensor x Cylinder block | 20 | 204 | 15 | |
| Exhaust manifold sub-assembly x Cylinder head sub-assembly | 21 | 214 | 15 | |
| Engine mount bracket x Cylinder block | 43 | 438 | 32 | |
| V-ribbed belt tensioner assembly x Cylinder block | 43 | 438 | 32 | |
| Oil pressure switch assembly x Oil filter bracket | 15 | 153 | 11 | |
| Ignition coil assembly x Cylinder head cover | 10 | 102 | 7 | |
| Bank cover bracket x Cylinder head cover | 10 | 102 | 7 | |
| Injector driver x Engine assembly | 10 | 102 | 7 | |
| Engine oil level sensor x Oil pan sub-assembly | 7.0 | 71 | 62 in.*lbf | |
| Water pump pulley x Water pump assembly | 21 | 214 | 15 | |
ENGINE ASSEMBLY
| Part Tightened | N*m | Kgf*cm | Ft.*lbf | |
|---|---|---|---|---|
| Camshaft timing oil control valve assembly x Cylinder head cover | 10 | 102 | 7 | |
| Spark plug x Cylinder head sub-assembly | 18 | 184 | 13 | |
| VVT sensor | 10 | 102 | 7 | |
| No. 2 oil pipe x Cylinder head cover | 60 | 612 | 44 | |
| No. 2 oil pipe x Cylinder block | 60 | 612 | 44 | |
| Cylinder head cover sub-assembly (Bank 1) x Cylinder head sub-assembly RH | Bolt A | 21 | 214 | 15 |
| Except Bolt A | 10 | 102 | 7 | |
| Cylinder head cover sub-assembly (Bank 2) x Cylinder head sub-assembly LH | Bolt A | 21 | 214 | 15 |
| Except Bolt A | 10 | 102 | 7 | |
| Cylinder block water drain cock sub-assembly | 30 | 306 | 22 | |
| Water drain cock plug x Water drain cock sub-assembly | 13 | 130 | 9 | |
| Rear water bypass joint x Cylinder head sub-assembly | 10 | 102 | 7 | |
| Crankshaft position sensor x Cylinder block sub-assembly | 10 | 102 | 7 | |
| Water inlet with thermostat sub-assembly x water inlet | 10 | 102 | 7 | |
| Water inlet x Cylinder head | 10 | 102 | 7 | |
| Engine rear oil seal retainer x Cylinder block sub-assembly | 10 | 102 | 7 | |
| Oil pan baffle plate x Cylinder block sub-assembly | 10 | 102 | 7 | |
| Oil strainer stud bolt x Cylinder block and timing chain cover | 4.0 | 41 | 35 in.*lbf | |
| Oil pan stud bolt x Oil pan sub-assembly | 4.0 | 41 | 35 in.*lbf | |
| Oil strainer sub-assembly x Cylinder block and timing chain or belt cover | 10 | 102 | 7 | |
| Oil filter cap x Oil pan sub-assembly | 25 | 255 | 18 | |
| Oil pan sub-assembly x Cylinder block and timing chain cover : bolt | Bolt A | 10 | 102 | 7 |
| Except Bolt A | 21 | 214 | 15 | |
| Oil pan sub-assembly x Cylinder block and timing chain cover : nut | 21 | 214 | 15 | |
| No. 2 oil pan sub-assembly x Oil pan sub-assembly | 10 | 102 | 7 | |
| Oil pan drain plug x No. 2 oil pan sub-assembly | 40 | 408 | 30 | |
| Timing chain cover plate x Timing chain cover sub-assembly | 9.1 | 93 | 81 in.*lbf | |
| Timing chain cover sub-assembly x Engine | Bolt A | 43 | 438 | 32 |
| Except Bolt A | 21 | 214 | 15 | |
| Nut | 21 | 214 | 15 | |
| Water pump assembly x Timing chain cover sub-assembly | Bolt A | 21 | 214 | 15 |
| Except Bolt A | 9.1 | 93 | 81 in.*lbf | |
| Crankshaft pulley x Crankshaft | 250 | 2,549 | 184 | |
| No. 1 idle gear x Cylinder block sub-assembly | 60 | 612 | 44 | |
| No. 1 chain vibration damper x Cylinder block sub-assembly | 23 | 235 | 17 | |
| Camshaft bearing cap x Camshaft housing | 1st | 10 | 102 | 7 |
| 2nd | 16 | 163 | 12 | |
| Camshaft housing x Cylinder head sub-assembly | 28 | 286 | 21 | |
| No. 1 chain tensioner x Cylinder head sub-assembly | 10 | 102 | 7 | |
| No. 2 chain tensioner x Cylinder head sub-assembly | 21 | 214 | 15 | |
| No. 3 chain tensioner x Cylinder head sub-assembly | 21 | 214 | 15 | |
| Camshaft timing gear assembly x Camshaft | 100 | 1,020 | 74 | |
| Water outlet pipe sub-assembly x Cylinder block sub-assembly | 10 | 102 | 7 | |
| Cylinder head x Cylinder block sub-assembly | 1st | 36 | 367 | 27 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| 3rd | Turn 90° | Turn 90° | Turn 90° | |
| Cylinder head sub-assembly x Cylinder block sub-assembly | Recessed head 1st | 36 | 367 | 27 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| 3rd | Turn 90° | Turn 90° | Turn 90° | |
| 14 mm (0.55 in.) head | 30 | 306 | 22 | |
| Union x Cylinder head sub-assembly | 15 | 153 | 11 | |
| No. 1 straight screw plug x Cylinder head sub-assembly | 44 | 449 | 32 | |
| No. 2 straight screw plug x Cylinder head sub-assembly | 80 | 816 | 59 | |
| Stud bolt x Cylinder head sub-assembly | For A, B and C bolts | 10 | 102 | 7 |
| For D bolts | 4.0 | 41 | 35 in.*lbf | |
| Main bearing cap x Cylinder block sub-assembly | 16 point head 1st | 61 | 622 | 45 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| 12 mm head | 26 | 265 | 19 | |
| Connecting rod cap x Connecting rod | 1st | 40 | 408 | 30 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| No. 1 oil nozzle sub-assembly x Cylinder block sub-assembly | 9.0 | 92 | 80 in.*lbf | |
| Ventilation valve x Cylinder head cover sub-assembly LH | 27 | 275 | 20 | |
| Oil check valve bolt x Cylinder block sub-assembly | 60 | 612 | 44 | |
| Oil pipe union x Cylinder head cover sub-assembly | 60 | 612 | 44 | |
| Stud bolt x Cylinder block sub-assembly | 10 | 102 | 7 | |
ENGINE UNIT