REMOVAL Land Rover Range Rover L322

REMOVAL

Scheme 12

Scheme 13

Scheme 14

Scheme 15

Scheme 16

1. Position the front seat fully forwards.
2. Remove the safety belt lower anchor bolt cover. Carefully release the clip from behind the front seat base side trim panel. Remove the cover.
3. Release the safety belt lower anchor from the front seat. Remove and discard the bolt.
4. Remove the 2 rear bolts from the front seat.
5. Remove the 2 front bolts from the front seat. Position the front seat fully rearwards.
6. Reposition the front seat to the central position. Reposition the front seat backrest to the fully upright position. Lower the front seat head restraint to the fully lowered position.
7. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
8. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
9. Reposition the front seat for access. Disconnect the 4 electrical connectors.
10. Reposition the RH front seat for access. Disconnect the 5 electrical connectors.
11. With assistance carefully remove the front seat. Fit protection around the door aperture to protect the interior.

Scheme 17

1. With assistance carefully install the front seat. Remove the protection from around the door aperture.
2. Reposition the front seat for access. Connect the 4 electrical connectors.
3. Reposition the front seat for access. Connect the 5 electrical connectors.
4. Reposition the front safety belt buckle wiring harness.
5. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
6. Install the 2 front bolts to the front seat. Align the front seat locating pegs. Position the front seat fully rearwards. Tighten the front seat front bolts to 45 Nm (33 lb.ft).
7. Install the 2 rear bolts to the front seat. Position the front seat fully forwards. Tighten the front seat rear bolts to 45 Nm (33 lb.ft).
8. Attach the safety belt lower anchor to the seat. Install a new bolt and tighten to 45 Nm (33 lb.ft).
9. Install the safety belt lower anchor bolt cover.
10. Reposition the front seat to the original position.

Scheme 18

Scheme 19

Scheme 20

Scheme 21

Scheme 22

Scheme 23

Scheme 24

Scheme 25

Scheme 26

Scheme 27

1. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
2. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
3. Remove the front seat head restraint. See «Front Seat Head Restraint - Vehicles With: Head Restraint Video Display»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
4. Remove the seat armrest. See «Seat Armrest»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
5. Remove the front seat backrest cover upper trim panel. Remove the 2 screws. Release the front seat backrest cover from the front seat backrest upper trim panel.
6. Remove the front seat backrest cooling duct. Remove the clip from the front seat backrest cooling duct.
7. Remove and discard the 2 clips from the front seat backrest cover.
8. Release the 2 outer tension straps from the front seat backrest.
9. Release the front seat side air bag sleeve from the front seat backrest cover outer tension strap.
10. Reposition the lumbar motor control valve.
11. Release the front seat side air bag sleeve. Remove and discard the front seat side air bag sleeve bolt. Remove and discard the front seat side air bag lower nut.
12. Reposition the front seat backrest heater and blower motor assembly. Carefully release the 2 clips.
13. Reposition the front seat backrest heater and blower motor assembly duct. Release the 2 clips.
14. Release the 3 inner central tension straps from the front seat backrest. Reposition the front seat backrest cover inner central tension straps to the front.
15. Remove the front seat head restraint guide tubes. Raise the front seat backrest cover from the front seat frame for access. Carefully release the 2 clips from the front seat head restraint guide tubes.
16. Remove the front seat backrest cushion and cover from the front seat frame.
17. Remove the front seat backrest cover from the front seat backrest cushion. Reposition the front seat backrest cover from the front seat backrest cushion. Remove and discard the 17 clips from the front seat backrest cover.

1. Install the front seat backrest cover to the front seat backrest cushion. Reposition the front seat backrest cover to the front seat backrest cushion. Install the 17 new clips to the front seat backrest cover.
2. Install the front seat backrest cushion and cover to the front seat frame.
3. Install the front seat head restraint guide tubes. Secure the head restraint guide tube clips. Reposition the front seat backrest cover to the original position.
4. Secure the 3 inner central tension straps to the front seat backrest. Reposition the front seat backrest cover inner central tension straps to the rear.
5. Reposition the front seat backrest heater and blower motor assembly duct. Secure the 2 clips.
6. Reposition the front seat backrest heater and blower motor assembly. Secure the 2 clips.
7. Secure the front seat side air bag sleeve. Tighten the new bolt to 3 Nm (2 lb.ft). Tighten the new nut to 7 Nm (5 lb.ft).
8. Reposition the lumbar motor control valve.
9. Secure the front seat side air bag sleeve to the front seat backrest cover outer tension strap.
10. Secure the 2 outer tension straps to the front seat backrest.
11. Install the 2 new clips to the front seat backrest cover.
12. Install the front seat backrest cooling duct. Install the clip to the front seat backrest cooling duct.
13. Install the front seat backrest cover upper trim panel. Install the front seat backrest cover to the front seat backrest upper trim panel. Install the 2 screws.
14. Install the seat armrest. See «Seat Armrest»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
15. Install the front seat head restraint. See «Front Seat Head Restraint - Vehicles With: Head Restraint Video Display»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
16. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .

Scheme 28

Scheme 29

Scheme 30

Scheme 31

1. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
2. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
3. Remove the front seat. See «Front Seat»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
4. Release the 2 lower tension straps from the front seat base. Reposition the front seat backrest cover for access.
5. Remove the front seat side trim panel support. Release the 2 clips.
6. Remove the seat control switch. See «Seat Control Switch»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
7. Remove the front seat backrest hinge cover. Remove the 2 screws. Release the clip.
8. Remove the 2 clips from the front seat backrest lower rear cover.
9. Remove the front seat backrest lower rear cover. Release the front seat backrest cover lower trim panel from the 2 clips.

1. Install the front seat backrest lower rear cover. Secure the front seat backrest cover lower trim panel to the 2 clips.
2. Install the 2 clips to the front seat backrest lower rear cover.
3. Install the front seat backrest hinge cover. Secure the clip. Install the 2 screws.
4. Install the seat control switch. See «Seat Control Switch»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
5. Install the front seat side trim panel support. Secure the 2 clips.
6. Secure the 2 lower tension straps to the front seat base. Reposition the front seat backrest cover.
7. Install the front seat. See «Front Seat»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
8. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .

Scheme 32

Scheme 33

Scheme 34

1. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
2. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
3. Remove the front seat backrest lower rear cover. See «Front Seat Backrest Lower Rear Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
4. Remove the front seat backrest cooling duct. Remove the clip from the front seat backrest cooling duct.
5. Remove and discard the clip from the front seat backrest cover.
6. Release the front seat backrest cover RH inner tension strap.
7. Reposition the front seat backrest heater and blower motor assembly. Carefully release the 2 clips.
8. Remove the 3 screws from the front seat backrest heater and blower motor assembly.
9. Remove the front seat backrest heater and blower motor assembly. Disconnect the front seat backrest heater and blower motor assembly electrical connector.

1. Install the front seat backrest heater and blower motor assembly. Connect the front seat backrest heater and blower motor assembly electrical connector.
2. Install the 3 screws to the front seat backrest heater and blower motor assembly.
3. Reposition the front seat backrest heater and blower motor assembly. Secure the 2 clips.
4. Secure the front seat backrest cover RH inner tension strap.
5. Install the new clip to the front seat backrest cover.
6. Install the front seat backrest cooling duct. Install the clip to the front seat backrest cooling duct.
7. Install the front seat backrest lower rear cover. See «Front Seat Backrest Lower Rear Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
8. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .

Scheme 35

Scheme 36

Scheme 37

Scheme 38

1. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
2. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
3. Remove the front seat cushion and front seat cushion cover from the front seat base. See «Front Seat Cushion Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
4. Reposition the front seat base wiring harness trim panel. Reposition the front seat for access. Remove the 4 screws.
5. Remove the front seat cushion heater and blower motor assembly duct. Remove the screw.
6. Remove the 3 screws from the front seat heater and blower motor assembly.
7. Remove the front seat cushion heater and blower motor assembly. Disconnect the front seat cushion heater and blower motor assembly electrical connector.

1. Install the front seat cushion heater and blower motor assembly. Connect the front seat cushion heater and blower motor assembly electrical connector.
2. Install the 3 screws to the front seat cushion heater and blower motor assembly.
3. Install the front seat cushion heater and blower motor assembly duct. Install the screw.
4. Reposition the front seat base wiring harness trim panel. Reposition the front seat for access. Install the 4 screws.
5. Install the front seat cushion and cover to the front seat base. See «Front Seat Cushion Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
6. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .

Scheme 39

Scheme 40

Scheme 41

Scheme 42

Scheme 43

Scheme 44

1. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
2. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
3. Remove the front seat. See «Front Seat»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
4. Release the 2 lower tension straps from the front seat base. Reposition the front seat backrest cover for access.
5. Remove the front seat side trim panel support. Release the 2 clips.
6. Remove the seat control switch. See «Seat Control Switch»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
7. Remove the front seat base side trim panel mounting bracket. Release the 2 wiring harness clips. Remove the 4 screws.
8. Remove the front seat backrest hinge cover. Remove the 2 screws. Release the clip.
9. Remove the 2 clips from the front seat backrest cover lower trim panel.
10. Remove the front seat backrest cover lower trim panel. Release the front seat backrest cover lower trim panel from the 2 clips.
11. Release the front seat cushion cover from the rear of the front seat base.
12. Release the front seat cushion cover from the left-hand side of the front seat base.
13. Release the front seat cushion cover from the right-hand side of the front seat base.
14. Remove the front seat cushion and front seat cushion cover from the front seat base. Reposition the front seat for access. Release the front seat cushion cover from the front of the front seat base.
15. Release the front seat cushion cover tension strap.
16. Remove and discard the 15 clips from the front seat cushion cover. Reposition the front seat cushion cover for access.
17. Remove the front seat cushion cover from the front seat cushion.

1. Install the front seat cushion cover to the front seat cushion.
2. Install the 15 new clips to the front seat cushion cover. Reposition the front seat cushion cover to the front seat cushion.
3. Secure the front seat cushion cover tension strap.
4. Install the front seat cushion and cover to the front seat base. Reposition the front seat for access. Secure the front seat cushion cover to the front of the front seat base.
5. Secure the front seat cushion cover to the right-hand side of the front seat base.
6. Secure the front seat cushion cover to the left-hand side of the front seat base.
7. Secure the front seat cushion cover to the rear of the front seat base.
8. Install the front seat backrest cover lower trim panel. Secure the front seat backrest cover lower trim panel to the 2 clips.
9. Install the 2 clips to the front seat backrest cover lower trim panel.
10. Install the front seat backrest hinge cover. Secure the clip. Install the 2 screws.
11. Install the front seat base side trim panel mounting bracket. Install the 4 screws. Secure the 2 wiring harness clips.
12. Install the seat control switch. See «Seat Control Switch»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
13. Install the front seat side trim panel support. Secure the 2 clips.
14. Secure the 2 lower tension straps to the front seat base. Reposition the front seat backrest cover.
15. Install the front seat. See «Front Seat»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
16. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
17. Using the Land Rover approved diagnostic system, calibrate the occupant classification sensor.

Scheme 45

Scheme 46

Scheme 47

Scheme 48

1. Reposition the front seat backrest for access. Reposition the front seat head restraint to the fully extended position.
2. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
3. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
4. Remove the front seat backrest cover lower trim panel. See «Front Seat Backrest Lower Rear Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
5. Disconnect the front seat head restraint video display electrical connector. Release the clip.
6. Release the front seat head restraint. Release the front seat head restraint from the head restraint clips.
7. Using a suitable tape secure the front seat head restraint post clip to the front seat head restraint wiring harness. Release the front seat head restraint post clip from the RH head restraint post.
8. Release the RH head restraint guide tube. Apply suitable protective tape around the RH head restraint guide tube. Using a suitable tool, release the RH head restraint guide tube.
9. Remove the front seat head restraint. Feed the front seat head restraint video wiring harness through the front seat backrest cover and the seat frame.

1. Install the front seat head restraint. Feed the front seat head restraint video wiring harness through the front seat backrest cover and the seat frame.
2. Secure the RH head restraint guide tube. Remove the protective tape from around the RH head restraint guide tube.
3. Remove the suitable tape from the front seat head restraint post clip. Secure the front seat head restraint post clip to the RH head restraint post.
4. Secure the front seat head restraint. Secure the front seat head restraint to the head restraint clips.
5. Connect the front seat head restraint video display electrical connector. Secure the clip.
6. Install the front seat backrest cover lower trim panel. See «Front Seat Backrest Lower Rear Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
7. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
8. Reposition the front seat backrest to its original position. Reposition the front seat head restraint to its original position.

1. Reposition the front seat backrest for access.
2. Remove the front seat head restraint. Reposition the front seat head restraint to the fully extended position. Release the front seat head restraint from the head restraint clips.

1. Install the front seat head restraint. Secure the front seat head restraint to the head restraint clips. Reposition the front seat head restraint to the original position.
2. Reposition the front seat backrest to the original position.

Scheme 49

Scheme 50

1. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
2. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
3. Remove the front seat head restraint. See «Front Seat Head Restraint - Vehicles With: Head Restraint Video Display»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
4. Remove the seat armrest. See «Seat Armrest»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
5. Remove the front seat backrest cover upper trim panel. Remove the 2 screws. Release the front seat backrest cover from the front seat backrest upper trim panel.
6. Remove the front seat backrest cooling duct. Remove the clip from the front seat backrest cooling duct.
7. Remove and discard the 2 clips from the front seat backrest cover.
8. Release the 2 outer tension straps from the front seat backrest.
9. Release the front seat side air bag sleeve from the front seat backrest cover outer tension strap.
10. Reposition the lumbar motor control valve.
11. Release the front seat side air bag sleeve. Remove and discard the front seat side air bag sleeve bolt. Remove and discard the front seat side air bag lower nut.
12. Reposition the front seat backrest heater and blower motor assembly. Carefully release the 2 clips.
13. Reposition the front seat backrest heater and blower motor assembly duct. Release the 2 clips.
14. Release the 3 inner central tension straps from the front seat backrest. Reposition the front seat backrest cover inner central tension straps to the front.
15. Remove the front seat head restraint motor screw. Raise the front seat backrest cover from the front seat frame for access.
16. Remove the front seat head restraint motor. Disconnect the electrical connector. Release the front seat head restraint motor from the front seat frame.

1. Install the front seat head restraint motor. Secure the front seat head restraint motor to the front seat frame. Connect the electrical connector.
2. Install the front seat head restraint motor screw. Reposition the front seat backrest cover to the original position.
3. Secure the 3 inner central tension straps to the front seat backrest. Reposition the front seat backrest cover inner central tension straps to the rear.
4. Reposition the front seat backrest heater and blower motor assembly duct. Secure the 2 clips.
5. Reposition the front seat backrest heater and blower motor assembly. Secure the 2 clips.
6. Secure the front seat side air bag sleeve. Tighten the new bolt to 3 Nm (2 lb.ft). Tighten the new nut to 7 Nm (5 lb.ft).
7. Reposition the lumbar motor control valve.
8. Secure the front seat side air bag sleeve to the front seat backrest cover outer tension strap.
9. Secure the 2 outer tension straps to the front seat backrest.
10. Install the 2 new clips to the front seat backrest cover.
11. Install the front seat backrest cooling duct. Install the clip to the front seat backrest cooling duct.
12. Install the front seat backrest cover upper trim panel. Install the front seat backrest cover to the front seat backrest upper trim panel. Install the 2 screws.
13. Install the seat armrest. See «Seat Armrest»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
14. Install the front seat head restraint. See «Front Seat Head Restraint - Vehicles With: Head Restraint Video Display»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
15. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .

Scheme 51

Scheme 52

1. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
2. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
3. Remove the front seat backrest cover. See «Front Seat Backrest Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
4. Reposition the front seat backrest shaft. Remove and discard the front seat backrest shaft clip.
5. Remove the front seat recliner motor. Disconnect the electrical connector. Remove the front seat recliner motor bolt.
6. Remove the front seat recliner motor bracket. Release the 2 clips.

1. Install the front seat recliner motor bracket. Secure the 2 clips.
2. Install the front seat recliner motor. Loosely install the front seat recliner motor bolt. Connect the electrical connector.
3. Reposition the front seat backrest shaft. Install the new front seat backrest shaft clip. Tighten the front seat recliner motor bolt.
4. Install the front seat backrest cover. See «Front Seat Backrest Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
5. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
6. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .

Scheme 53

Scheme 54

1. Disconnect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .
2. Make the air bag supplemental restraint system (SRS) safe. Refer to «Standard Workshop Practices»(/land-rover/range-rover/l322-2005-2009/remont/oem-general-information/#general-information) .
3. Remove the front seat backrest lower rear cover. See «Front Seat Backrest Lower Rear Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
4. Reposition the front seat backrest heater and blower motor assembly. Carefully release the 2 clips.
5. Reposition the front seat backrest heater and blower motor assembly duct. Release the 2 clips.
6. Reposition the lumbar motor control valve. Disconnect the 2 electrical connectors.
7. Remove the lumbar assembly. Release the 2 retaining tangs.

1. Install the lumbar assembly. Secure the 2 retaining tangs.
2. Reposition the lumbar motor control valve. Connect the 2 electrical connectors.
3. Reposition the front seat backrest heater and blower motor assembly duct. Secure the 2 clips.
4. Reposition the front seat backrest heater and blower motor assembly. Secure the 2 clips.
5. Install the front seat backrest lower rear cover. See «Front Seat Backrest Lower Rear Cover»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
6. Connect the battery ground cable. Refer to «Specifications»(/land-rover/range-rover/l322-2005-2009/remont/charging-system/#charging-system-general-information__specifications) .

Note. Front seat shown removed for clarity.

Scheme 55

Scheme 56

Scheme 57

1. Position the front seat fully forwards.
2. Remove the safety belt lower anchor bolt cover. Carefully release the clip from behind the front seat base side trim panel. Remove the cover.
3. Carefully release the front seat base side trim panel. Remove the 2 screws. Release the 6 clips.
4. Disconnect the lumbar control switch electrical connector.
5. Remove the lumbar control switch. Release the 2 clips. Remove the switch.

1. Install the lumbar control switch. Install the switch. Secure the 2 clips.
2. Connect the lumbar control switch electrical connector.
3. Carefully install the front seat base side trim panel. Secure the 6 clips. Install the 2 screws.
4. Install the safety belt lower anchor bolt cover.
5. Reposition the front seat to the original position.

Scheme 58

Scheme 59

1. Reposition the front seat for access. Reposition the seat armrest to the central position. Apply suitable protective tape around the seat armrest.
2. Remove the seat armrest. Remove the T27 Torx bolt.

1. Install the seat armrest. Align the seat armrest. Install the T27 Torx bolt and tighten to 25 Nm (18 lb.ft).
2. Reposition the front seat to the original position. Remove the suitable protective tape from around the seat armrest. Reposition the seat armrest to the original position.

Note. Front seat shown removed for clarity.

Scheme 60

1. Position the front seat fully forwards.
2. Remove the safety belt lower anchor bolt cover. Carefully release the clip from behind the front seat base side trim panel. Remove the cover.
3. Carefully release the front seat base side trim panel. Remove the 2 screws. Release the 2 front clips. Release the rear clip. Release the 3 fir tree clips.
4. Release the seat control switch. Release the 5 clips.
5. Remove the seat control switch. Disconnect the 4 electrical connectors.

1. Install the seat control switch. Connect the 4 electrical connectors.
2. Secure the seat control switch. Secure the 5 clips.
3. Secure the front seat base side trim panel. Secure the 6 clips. Install the 2 screws.
4. Install the safety belt lower anchor bolt cover.
5. Reposition the front seat to the original position.

Scheme 61

Scheme 62

1. Remove the 2 bolts from the front of the rear seat hinge plates. Fit protection around the door aperture to protect the interior. Remove the 2 bolt covers from the front of the rear seat hinge plates.
2. Fold the rear seat fully forwards. Release the rear seat backrest catch.
3. With assistance carefully remove the rear seat. Disconnect the electrical connector. Remove the 2 nuts from the rear of the rear seat hinge plates.

1. With assistance carefully install the rear seat. Install the 2 nuts to the rear of the rear seat hinge plates. Tighten to 25 Nm (18 lb.ft). Connect the electrical connector.
2. Fold the rear seat fully rearwards. Secure the rear seat backrest catch.
3. Install the 2 bolts to the front of the rear seat hinge plates. Tighten to 25 Nm (18 lb.ft). Install the 2 bolt covers to the front of the rear seat hinge plates. Remove the protection from around the door aperture.

Scheme 63

Scheme 64

Scheme 65

1. Reposition the RH rear seat fully forward. Release the RH rear seat backrest catch.
2. Remove the LH rear seat backrest inner hinge cover. Remove the 3 screws.
3. Reposition the rear seat armrest fully forwards. Release the rear seat armrest catch.
4. Release the rear seat armrest cover from the rear seat backrest. Release the rear seat armrest cover securing strip. Release the rear seat armrest cover securing rail.
5. Remove the rear seat armrest. Remove the bolt. Reposition the rear seat armrest from the rear seat armrest hinge.

1. Install the rear seat armrest. Reposition the rear seat armrest to the rear seat armrest hinge. Install the bolt and tighten to 10 Nm (7 lb.ft).
2. Secure the rear seat armrest cover to the rear seat backrest. Secure the rear seat armrest cover securing rail. Secure the rear seat armrest cover securing strip.
3. Reposition the rear seat armrest to the original position. Secure the rear seat armrest catch.
4. Install the LH rear seat backrest inner hinge cover. Install the 3 screws.
5. Reposition the RH rear seat to the original position. Secure the RH rear seat backrest catch.

Scheme 66

Scheme 67

Scheme 68

Scheme 69

Scheme 70

Scheme 71

Scheme 72

Scheme 73

Scheme 74

Scheme 75

Scheme 76

Scheme 77

1. Remove the rear seat. See «Rear Seat»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
2. Remove the rear seat backrest catch trim panel. Release the 3 clips.
3. Remove the rear seat backrest rear cover lower trim panel. Remove the 2 screws. Release the 3 clips.
4. Carefully release the rear seat backrest cover from the upper part of the rear seat frame.
5. Remove the rear seat backrest rear cover inner side trim panel. Release the rear seat armrest cover securing strip. Remove the screw. Release the 11 inner side trim panel clips from the rear seat backrest cover.
6. Remove the rear seat backrest rear cover. Release the rear seat backrest rear cover adhesive.
7. Remove the rear seat backrest inner hinge cover. Remove the 3 screws.
8. Remove the rear seat base lower trim panel. Remove the 6 clips. Reposition the rear seat hinge plates for access.
9. Reposition the rear seat armrest fully forwards. Release the rear seat armrest catch.
10. Release the rear seat armrest cover from the rear seat backrest. Release the rear seat armrest cover securing strip. Release the rear seat armrest cover securing rail.
11. Remove the rear seat armrest. Remove the bolt. Reposition the rear seat armrest from the rear seat armrest hinge.
12. Remove the rear seat backrest inner hinge. Remove the 4 bolts. Discard the 2 lower bolts.
13. Remove the rear seat backrest outer hinge cover. Remove the 2 screws.
14. Remove the rear seat backrest from the rear seat base. Remove the rear seat backrest outer hinge bolt.
15. Remove the rear seat backrest hinge wiring harness clip. Remove the 2 clips. Release the rear seat base wiring harness electrical connector from the rear seat backrest cover. Disconnect the rear seat base wiring harness electrical connector.
16. Release the rear seat cushion cover from the rear seat base.
17. Reposition the safety belt through the rear seat cushion cover and the rear seat cushion. Remove and discard the safety belt bolt from the rear seat base.
18. Remove the rear seat backrest cover safety belt trim panel. Remove the 2 screws.
19. Release the rear seat backrest cover from the rear seat backrest.
20. Remove the rear seat backrest catch trim panel. Carefully release the 4 clips.
21. Reposition the rear seat backrest cushion and cover from the rear seat backrest for access.
22. Reposition the safety belt through the rear seat backrest cushion and cover.
23. Using a suitable tool, release the head restraint guide tubes. Release the 6 clips.
24. Remove the rear seat backrest cushion and cover from the rear seat backrest. Reposition the safety belt.
25. Remove the rear seat backrest cover from the rear seat backrest cushion. Remove and discard the 16 clips from the rear seat backrest cover.

1. Install the rear seat backrest cover to the rear seat backrest cushion. Install the 16 new clips to the rear seat backrest cover.
2. Install the rear seat backrest cushion and cover to the rear seat backrest. Reposition the safety belt.
3. Install the head restraint guide tubes. Secure the 6 clips.
4. Reposition the safety belt through the rear seat backrest cushion and cover.
5. Reposition the rear seat backrest cushion and cover to the rear seat backrest.
6. Install the rear seat backrest catch trim panel. Secure the 4 clips.
7. Secure the rear seat backrest cover to the rear seat backrest.
8. Install the rear seat backrest cover safety belt trim panel. Install the 2 screws.
9. Reposition the safety belt through the rear seat cushion cover and the rear seat cushion. Install the new safety belt bolt to the rear seat base and tighten to 31 Nm (23 lb.ft).
10. Secure the rear seat cushion cover to the rear seat base.
11. Install the rear seat backrest hinge wiring harness clip. Secure the 2 clips. Secure the rear seat base wiring harness electrical connector to the rear seat backrest cover. Connect the rear seat base wiring harness electrical connector.
12. Secure the rear seat backrest to the rear seat base. Install the rear seat backrest outer hinge bolt and tighten to 45 Nm (33 lb.ft).
13. Install the rear seat backrest outer hinge cover. Install the 2 screws.
14. Install the rear seat backrest inner hinge. Install the 2 upper bolts. Install the 2 new lower bolts. Tighten the bolts to 25 Nm (18 lb.ft).
15. Install the rear seat armrest. Install the bolt. Reposition the rear seat armrest to the rear seat armrest hinge.
16. Secure the rear seat armrest cover to the rear seat backrest. Secure the rear seat armrest cover securing strip. Secure the rear seat armrest cover securing rail.
17. Reposition the rear seat armrest to the original position. Secure the rear seat armrest catch.
18. Install the rear seat base lower trim panel. Install the 6 clips. Reposition the rear seat hinge plates for access.
19. Install the rear seat backrest inner hinge cover. Install the 3 screws.
20. Install the rear seat backrest rear cover. Apply a suitable adhesive to the rear seat backrest rear cover.
21. Install the rear seat backrest rear cover inner side trim panel. Secure the 11 inner side trim panel clips to the rear seat backrest cover. Install the screw. Secure the rear seat armrest cover securing strip.
22. Carefully secure the rear seat backrest cover to the upper part of the rear seat frame.
23. Install the rear seat backrest rear cover lower trim panel. Secure the 3 clips. Install the 2 screws.
24. Install the rear seat backrest catch trim panel. Secure the 3 clips.
25. Install the rear seat. See «Rear Seat»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .

1. Remove the LH rear seat. See «Rear Seat»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .
2. Remove the rear seat backrest outer hinge cover. Remove the 2 screws.
3. Remove the rear seat backrest inner hinge cover. Remove the 3 screws.
4. Remove the rear seat base lower trim panel. Remove the 6 clips. Reposition the rear seat hinge plates for access.
5. Remove the rear seat backrest inner hinge. Remove the 4 bolts. Discard the 2 lower bolts.
6. Remove the rear seat backrest from the rear seat base. Remove the rear seat backrest outer hinge bolt.
7. Remove the rear seat backrest hinge wiring harness clip. Remove the 2 clips. Release the rear seat base wiring harness electrical connector from the rear seat backrest cover. Disconnect the rear seat base wiring harness electrical connector.
8. Release the rear seat cushion cover from the rear seat base.
9. Reposition the rear seat base wiring harness through the rear seat base. Release the rear seat base wiring harness electrical connector from the clip. Release the 5 wiring harness clips.
10. Reposition the safety belt through the rear seat cushion cover and the rear seat cushion. Remove and discard the safety belt bolt from the rear seat base.
11. Remove the rear seat cushion cover and the rear seat cushion.
12. Remove the rear seat cushion cover from the rear seat cushion. Remove and discard the 25 rear seat cushion cover clips.

1. Install the rear seat cushion cover to the rear seat cushion. Install the 25 new rear seat cushion cover clips.
2. Install the rear seat cushion cover and the rear seat cushion.
3. Reposition the safety belt through the rear seat cushion cover and the rear seat cushion. Install the new safety belt bolt to the rear seat base and tighten to 31 Nm (23 lb.ft).
4. Reposition the rear seat base wiring harness through the rear seat base. Secure the 5 wiring harness clips. Install the rear seat base wiring harness electrical connector to the clip.
5. Secure the rear seat cushion cover to the rear seat base.
6. Install the rear seat backrest hinge wiring harness clip. Install the 2 clips. Connect the rear seat base wiring harness electrical connector. Secure the rear seat base wiring harness electrical connector to the rear seat backrest cover.
7. Install the rear seat backrest to the rear seat base. Install the rear seat backrest outer hinge bolt and tighten to 45Nm (33 lb.ft).
8. Install the rear seat backrest inner hinge. Install the 4 bolts. Install the 2 new lower bolts. Tighten the bolts to 45 Nm (33 lb.ft).
9. Install the rear seat base lower trim panel. Reposition the rear seat hinge plates for access. Install the 6 clips.
10. Install the rear seat backrest inner hinge cover. Install the 3 screws.
11. Install the rear seat backrest outer hinge cover. Install the 2 screws.
12. Install the LH rear seat. See «Rear Seat»(/land-rover/range-rover/l322-2005-2009/remont/seats/#seating) .

Scheme 78

Scheme 79

Scheme 80

Scheme 81

Scheme 82

1. Remove the head restraint.
2. Using a suitable tool, release the cover rear tab from the retaining tang.
3. Using a suitable tool, release the cover front tab from the retaining tang.
4. Using a suitable tool, release the cover side tabs from the retaining tang.
5. Position the foam pad to allow the head restraint frame to be removed.
6. Remove the head restraint frame.

Scheme 83

Scheme 84

Scheme 85

Scheme 86

Scheme 87

1. Remove the head restraint frame.
2. Make sure that the foam pad is installed back to its original orientation.
3. Using a suitable tool, secure the cover side tabs to the retaining tang.
4. Using a suitable tool, secure the cover front tab to the retaining tang.
5. Using a suitable tool, secure the cover rear tab to the retaining tang.
6. Make sure that the cushion is correctly located in the position illustrated.
7. Install the head restraint.

See also:
• Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS)
• Control Components
• Specifications
• Standard Workshop Practices
• SEATS
• PINPOINT TEST A
• PINPOINT TEST B
• PINPOINT TEST C
• PINPOINT TEST D
• PINPOINT TEST E
• Front Seat Head Restraint - Vehicles With: Head Restraint Video Display