Engine Controls - Self-Diagnostics - with Codes Land Rover Range Rover L322

DIAGNOSTIC TROUBLE CODE DEFINITIONS

ENGINE MANAGEMENT "P" CODES

GENERAL

When diagnosing an electrical fault follow the steps below

1. Read the circuit description appropriate to the reported fault to ensure a good understanding of circuit operation.
2. Study the power distribution, fuse details and earth (ground) distribution diagrams and identify other circuits which share fuses and/or earth points. Check whether these circuits operate correctly.
3. Using connector views, locate a point on the circuit (approximately half way between supply and earth) which is easily accessible.
4. Check that the pin out details of the connector are correct and that the correct signals exist at the correct terminals.
5. Continue to the next point on the circuit which is easiest to access and repeat the above.
6. Continue this approach until a fault is found, rectify the fault and then verify that the circuit operates correctly.

DIAGNOSTIC TESTS

Note. While limited diagnostic information is available, vehicle manufacturer does not support diagnostic information using aftermarket scan tools. To properly diagnose vehicle, it is recommended to use Textbook/T4 scan tool with appropriate adapter cables. Before replacing any component that scan tool suggests are faulty, ensure that all wiring connections and harness connectors are okay. Ensure that power and ground circuits are functioning properly.

Note. For circuit identification, see ENGINE PERFORMANCE in appropriate SYSTEM WIRING DIAGRAMS article in ELECTRICAL. For component locations, see appropriate COMPONENT LOCATION article in ELECTRICAL.

Possible Causes

1. Connectors C0606, C0176. See step 1 under CHECK.
2. Camshaft sensor bank 1. See step 2 under CHECK.

Check

1. Connector Connectors C0606, C0176. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. Camshaft Sensor Bank 1 No detail available for this fault.

1. VANOS actuator bank 1. See step 1 under CHECK.

1. VANOS Actuator Bank 1 No detail available for this fault.

1. VANOS actuator bank 1. See step 1 under CHECK.

1. VANOS Actuator Bank 1 No detail available for this fault.

1. Connectors C0606, C1463. See step 1 under CHECK.
2. Camshaft sensor bank 2. See step 2 under CHECK.

1. Connector Connectors C0606, C1463. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. Camshaft Sensor Bank 2 No detail available for this fault.

1. VANOS actuator bank 2. See step 1 under CHECK.

1. VANOS Actuator Bank 2 No detail available for this fault.

1. VANOS actuator bank 2. See step 1 under CHECK.

1. VANOS Actuator Bank 2 No detail available for this fault.

1. Short circuit C0604-19 (N) to ground. See step 1 under CHECK.
2. Short circuit C0604-15 (B) to ground. See step 2 under CHECK.
3. Connector C0604, C0644. See step 3 under CHECK.
4. Oxygen sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0604-19 (N) to ground. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0604-15 (B) to ground. Check resistance < 5.0ohm.
3. CONNECTOR Connector C0604, C0644. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Oxygen Sensor No detail available for this fault.

1. Short circuit C0604-19 (N) to battery voltage. See step 1 under CHECK.
2. Short circuit C0604-15 (B) to battery voltage. See step 2 under CHECK.
3. Connector C0604, C0644. See step 3 under CHECK.
4. Oxygen sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0604-19 (N) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0604-15 (B) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connector C0604, C0644. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Oxygen Sensor No detail available for this fault.

1. Connector C0604, C0644. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Oxygen sensor. See step 3 under CHECK.

1. CONNECTOR Connector C0604, C0644. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Oxygen Sensor No detail available for this fault.

1. Connector C0604, C0643. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Oxygen sensor. See step 3 under CHECK.

1. CONNECTOR Connector C0604, C0643. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Oxygen Sensor No detail available for this fault.

1. Short circuit C0604-7 (NU) to ground. See step 1 under CHECK.
2. Short circuit C0604-17 (BU) to ground. See step 2 under CHECK.
3. Connector C0604, C0643. See step 3 under CHECK.
4. Oxygen sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0604-7 (NU) to ground. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0604-17 (BU) to ground. Check resistance < 5.0ohm.
3. CONNECTOR Connector C0604, C0643. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Oxygen Sensor No detail available for this fault.

1. Short circuit C0604-7 (NU) to battery voltage. See step 1 under CHECK.
2. Short circuit C0604-17 (BU) to battery voltage. See step 2 under CHECK.
3. Connector C0604, C0643. See step 3 under CHECK.
4. Oxygen sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0604-7 (NU) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0604-17 (BU) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connector C0604, C0643. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Oxygen Sensor No detail available for this fault.

1. Connector C0604, C0645. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Oxygen sensor. See step 3 under CHECK.

1. CONNECTOR Connector C0604, C0645. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Oxygen Sensor No detail available for this fault.

1. Short circuit C0604-13 (NR) to ground. See step 1 under CHECK.
2. Short circuit C0604-16 (BR) to ground. See step 2 under CHECK.
3. Connector C0604, C0645. See step 3 under CHECK.
4. Oxygen sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0604-13 (NR) to ground. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0604-16 (BR) to ground. Check resistance < 5.0ohm.
3. CONNECTOR Connector C0604, C0645. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Oxygen Sensor No detail available for this fault.

1. Short circuit C0604-13 (NR)to battery voltage. See step 1 under CHECK.
2. Short circuit C0604-16 (BR) to battery voltage. See step 2 under CHECK.
3. Connector C0604, C0645. See step 3 under CHECK.
4. Oxygen sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0604-13 (NR) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0604-16 (BR) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connector C0604, C0645. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Oxygen Sensor No detail available for this fault.

1. Connector C0604, C0642. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Oxygen sensor. See step 3 under CHECK.

1. CONNECTOR Connector C0604, C0642. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Oxygen Sensor No detail available for this fault.

1. Short circuit C0604-1 (BW) to ground. See step 1 under CHECK.
2. Short circuit C0604-14 (NW) to ground. See step 2 under CHECK.
3. Connector C0604, C0642. See step 3 under CHECK.
4. Oxygen sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0604-1 (BW) to ground. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0604-14 (NW) to ground. Check resistance < 5.0ohm.
3. CONNECTOR Connector C0604, C0642. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Oxygen Sensor No detail available for this fault.

1. Short circuit C0604-1 (NW) to battery voltage. See step 1 under CHECK.
2. Short circuit C0604-14 (BW) to battery voltage. See step 2 under CHECK.
3. Connector C0604, C0642. See step 3 under CHECK.
4. Oxygen sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0604-1 (NW) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0604-14 (BW) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connector C0604, C0642. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Oxygen Sensor No detail available for this fault.

1. Short circuit C0606/7 (RG) to ground. See step 1 under CHECK.
2. Open circuit C0606/7 (RG) - C0149/4 (RG). See step 2 under CHECK.
3. Short circuit C0606/23 (Y) to ground. See step 3 under CHECK.
4. Open circuit C0606/23 (Y) - C0149/5 (Y). See step 4 under CHECK.
5. Connectors C0606, C0149. See step 5 under CHECK.
6. Mass airflow sensor. See step 6 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/7 (RG) to ground. Check resistance < 5.0ohm.
2. OPEN_CIRCUIT Open circuit C0606/7 (RG) - C0149/4 (RG). Check resistance > 1Mohm.
3. SHORT_CIRCUIT Short circuit C0606/23 (Y) to ground. Check resistance < 5.0ohm.
4. OPEN_CIRCUIT Open circuit C0606/23 (Y) - C0149/5 (Y). Check resistance > 1Mohm.
5. CONNECTOR Connectors C0606, C0149. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
6. Mass Airflow Sensor No detail available for this fault.

1. Short circuit C0606/23 (Y) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/23 (Y) - 5 Volts. See step 2 under CHECK.
3. Connectors C0606, C0149. See step 3 under CHECK.
4. Mass airflow sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/23 (Y) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/23 (Y) - 5 Volts. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0149. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Mass Airflow Sensor No detail available for this fault.

1. Connectors C0149, C0606, C0175, C0787. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Mass air flow sensor interface. See step 3 under CHECK.
4. Electronic Throttle interface. See step 4 under CHECK.

1. CIRCUIT_INTEGRITY Connectors C0149, C0606, C0175, C0787. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CONNECTOR Harness integrity. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Mass Air Flow Sensor Interface No detail available for this fault.
4. Electronic Throttle Interface No detail available for this fault.

1. V8 Engine Management System ECM. See step 1 under CHECK.

1. V8 Engine Management System ECM No detail available for this fault.

1. V8 Engine Management System ECM. See step 1 under CHECK.

1. V8 Engine Management System ECM No detail available for this fault.

1. Short circuit C0606/34(YU) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/34 (YU) - 5 Volts. See step 2 under CHECK.
3. Open circuit C0606/34 (YU) - C0149/1 (YU). See step 3 under CHECK.
4. Short circuit C0606/9(B) to battery voltage. See step 4 under CHECK.
5. Short circuit C0606/9 (B) - 5 Volts. See step 5 under CHECK.
6. Open circuit C0606/9 (B) - C0149/3 (B). See step 6 under CHECK.
7. Connectors C0606, C0149. See step 7 under CHECK.
8. Intake air temperature sensor. See step 8 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/34(YU) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/34 (YU) - 5 Volts. Check resistance < 5.0ohm.
3. OPEN_CIRCUIT Open circuit C0606/34 (YU) - C0149/1 (YU). Check resistance > 1Mohm.
4. SHORT_CIRCUIT Short circuit C0606/9(B) to battery voltage. Check resistance < 5.0ohm.
5. SHORT_CIRCUIT Short circuit C0606/9 (B) - 5 Volts. Check resistance < 5.0ohm.
6. OPEN_CIRCUIT Open circuit C0606/9 (B) - C0149/3 (B). Check resistance > 1Mohm.
7. CONNECTOR Connectors C0606, C0149. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
8. Intake Air Temperature Sensor No detail available for this fault.

1. Short circuit C0606/34 (YU) to ground. See step 1 under CHECK.
2. Short circuit C0606/7 (RG) to ground. See step 2 under CHECK.
3. Open circuit C0606/7 (RG) - C0149/4 (RG). See step 3 under CHECK.
4. Connectors C0606, C0149. See step 4 under CHECK.
5. Intake air temperature sensor. See step 5 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/34 (YU) to ground. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/7 (RG) to ground. Check resistance < 5.0ohm.
3. OPEN_CIRCUIT Open circuit C0606/7 (RG) - C0149/4 (RG). Check resistance > 1Mohm.
4. CONNECTOR Connectors C0606, C0149. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
5. Intake Air Temperature Sensor No detail available for this fault.

1. Harness integrity. See step 1 under CHECK.
2. Connectors C0331, C0787. See step 2 under CHECK.
3. Engine coolant temperature sensor. See step 3 under CHECK.

1. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Engine Coolant Temperature Sensor No detail available for this fault.

1. Short circuit C0606/21 (NO) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/21 (NO) - 5V. See step 2 under CHECK.
3. Short circuit C0606/21 (NO) to ground. See step 3 under CHECK.
4. Open circuit C0606/21 (NO) - C0169/4 (NO). See step 4 under CHECK.
5. Short circuit C0606/22 (YG) to battery voltage. See step 5 under CHECK.
6. Short circuit C0606/22 (YG) - 5V. See step 6 under CHECK.
7. Short circuit C0606/22 (YG) to ground. See step 7 under CHECK.
8. Open circuit C0606/22 (YG) - C0169/3 (YG). See step 8 under CHECK.
9. Connectors C0606, C0169. See step 9 under CHECK.
10. Engine coolant temperature sensor. See step 10 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/21 (NO) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/21 (NO) - 5V. Check resistance < 5.0ohm.
3. SHORT_CIRCUIT Short circuit C0606/21 (NO) to ground. Check resistance < 5.0ohm.
4. OPEN_CIRCUIT Open circuit C0606/21 (NO) - C0169/4 (NO). Check resistance > 1Mohm.
5. SHORT_CIRCUIT Short circuit C0606/22 (YG) to battery voltage. Check resistance < 5.0ohm.
6. SHORT_CIRCUIT Short circuit C0606/22 (YG) - 5V. Check resistance < 5.0ohm.
7. SHORT_CIRCUIT Short circuit C0606/22 (YG) to ground. Check resistance < 5.0ohm.
8. OPEN_CIRCUIT Open circuit C0606/22 (YG) - C0169/3 (YG). Check resistance > 1Mohm.
9. CONNECTOR Connectors C0606, C0169. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
10. Engine Coolant Temperature Sensor No detail available for this fault.

1. Short circuit C0606/21 (NO) to ground. See step 1 under CHECK.
2. Connectors C0606, C0169. See step 2 under CHECK.
3. Engine coolant temperature sensor. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/21 (NO) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0169. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Engine Coolant Temperature Sensor No detail available for this fault.

1. Harness integrity. See step 1 under CHECK.
2. Connectors C0331, C0787. See step 2 under CHECK.
3. Engine coolant temperature sensor. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Engine Coolant Temperature Sensor No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Throttle is in limp home mode. See step 1 under CHECK.

1. Throttle Is In Limp Home Mode No detail available for this fault.

1. Harness integrity. See step 1 under CHECK.
2. Connectors C0331, C0787. See step 2 under CHECK.
3. Throttle Body. See step 3 under CHECK.

1. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Throttle Body No detail available for this fault.

1. Short circuit C0331/8 (W) - ground. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Connectors C0331, C0787. See step 3 under CHECK.
4. Throttle Body. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/8 (W) to ground. Check resistance < 5.0ohm.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Throttle Body No detail available for this fault.

1. Short circuit C0331/8 (W) to ground. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Connectors C0331, C0787. See step 3 under CHECK.
4. Throttle Body. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/8 (W) to ground. Check resistance < 5.0ohm.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Throttle Body No detail available for this fault.

1. Connectors C0606, C0331, C2348, C0169, C0422. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Thermostat stuck open. See step 3 under CHECK.
4. Engine coolant temperature sensor. See step 4 under CHECK.
5. Radiator outlet temperature sensor. See step 5 under CHECK.

1. CONNECTOR Connectors C0606, C0331, C2348, C0169, C0422. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Thermostat Stuck Open No detail available for this fault.
4. Engine Coolant Temperature Sensor No detail available for this fault.
5. Radiator Outlet Temperature Sensor No detail available for this fault.

1. Short circuit C0606/19 (N) to battery voltage. See step 1 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/19 (N) to battery voltage. Check resistance < 5.0ohm.

1. Short circuit C0606/19 (N) to ground. See step 1 under CHECK.
2. Short circuit C0606/9 (Y) to ground. See step 2 under CHECK.
3. Connectors C0606, C0642. See step 3 under CHECK.
4. O2 Sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/19 (N) to ground. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/9 (Y) to ground. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0642. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. O2 Sensor No detail available for this fault.

1. Short circuit C0606/19 (N) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/9 (Y) to battery voltage. See step 2 under CHECK.
3. Connectors C0606, C0644. See step 3 under CHECK.
4. O2 Sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/19 (N) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/9 (Y) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0644. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. O2 Sensor No detail available for this fault.

1. Bank 1 upstream O2 sensor. See step 1 under CHECK.

1. Bank 1 Upstream O2 Sensor No detail available for this fault.

1. Bank 1 upstream O2 sensor. See step 1 under CHECK.

1. Bank 1 Upstream O2 Sensor No detail available for this fault.

1. Short circuit C0606/9 (Y) - C0644/3 (Y). See step 1 under CHECK.
2. Connectors C0606, C0644. See step 2 under CHECK.
3. O2 Sensor. See step 3 under CHECK.

1. OPEN_CIRCUIT Short circuit C0606/9 (Y) - C0644/3 (Y). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0644. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. O2 Sensor No detail available for this fault.

1. Connector C0604, C0644. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Oxygen sensor. See step 3 under CHECK.

1. CONNECTOR Connector C0604, C0644. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Oxygen Sensor No detail available for this fault.

1. Short circuit C0606/11 (YU) to battery voltage. See step 1 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/11 (YU) to battery voltage. Check resistance < 5.0ohm.

1. Short circuit C0606/11 (YU) to ground. See step 1 under CHECK.
2. Short circuit C0606/7 (NU) to ground. See step 2 under CHECK.
3. Connectors C0606, C0643. See step 3 under CHECK.
4. O2 Sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/11 (YU) to ground. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/7 (NU) to ground. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0643. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. O2 Sensor No detail available for this fault.

1. Short circuit C0606/11 (YU) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/7 (NU) to battery voltage. See step 2 under CHECK.
3. Connectors C0606, C0643. See step 3 under CHECK.
4. O2 Sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/11 (YU) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/7 (NU) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0643. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. O2 Sensor No detail available for this fault.

1. Bank 1 downstream O2 sensor. See step 1 under CHECK.

1. Bank 1 Downstream O2 Sensor No detail available for this fault.

1. Bank 1 downstream O2 sensor. See step 1 under CHECK.

1. Bank 1 Downstream O2 Sensor No detail available for this fault.

1. Bank 1 downstream O2 sensor. See step 1 under CHECK.

1. Bank 1 Downstream O2 Sensor No detail available for this fault.

1. Short circuit C0606/11 (YU) - C0643/3 (YU). See step 1 under CHECK.
2. Connectors C0606, C0643. See step 2 under CHECK.
3. O2 Sensor. See step 3 under CHECK.

1. OPEN_CIRCUIT Short circuit C0606/11 (YU) - C0643/3 (YU). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0643. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. O2 Sensor No detail available for this fault.

1. Connector C0604, C0643. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Oxygen sensor. See step 3 under CHECK.

1. CONNECTOR Connector C0604, C0643. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Oxygen Sensor No detail available for this fault.

1. Short circuit C0606/13 (NR) to battery voltage. See step 1 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/13 (NR) to battery voltage. Check resistance < 5.0ohm.

1. Short circuit C0606/13 (NR) to ground. See step 1 under CHECK.
2. Short circuit C0606/10 (YR) to ground. See step 2 under CHECK.
3. Connectors C0606, C0645. See step 3 under CHECK.
4. O2 Sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/13 (NR) to ground. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/10 (YR) to ground. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0645. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. O2 Sensor No detail available for this fault.

1. Short circuit C0606/13 (NR) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/10 (YR) to battery voltage. See step 2 under CHECK.
3. Connectors C0606, C0645. See step 3 under CHECK.
4. O2 Sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/13 (NR) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/10 (YR) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0645. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. O2 Sensor No detail available for this fault.

1. Bank 2 upstream O2 sensor. See step 1 under CHECK.

1. Bank 2 Upstream O2 Sensor No detail available for this fault.

1. Bank 2 upstream O2 sensor. See step 1 under CHECK.

1. Bank 2 Upstream O2 Sensor No detail available for this fault.

1. Short circuit C0606/10 (YR) - C0645/3 (YR). See step 1 under CHECK.
2. Connectors C0606, C0645. See step 2 under CHECK.
3. O2 Sensor. See step 3 under CHECK.

1. OPEN_CIRCUIT Short circuit C0606/10 (YR) - C0645/3 (YR). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0645. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. O2 Sensor No detail available for this fault.

1. Connector C0604, C0645. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Oxygen sensor. See step 3 under CHECK.

1. CONNECTOR Connector C0604, C0645. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Oxygen Sensor No detail available for this fault.

1. Short circuit C0606/1 (NW) to battery voltage. See step 1 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/1 (NW) to battery voltage. Check resistance < 5.0ohm.

1. Short circuit C0606/8 (YW) to ground. See step 1 under CHECK.
2. Short circuit C0606/1 (NW) to ground. See step 2 under CHECK.
3. Connectors C0606, C0642. See step 3 under CHECK.
4. O2 Sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/8 (YW) to ground. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/1 (NW) to ground. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0642. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. O2 Sensor No detail available for this fault.

1. Short circuit C0606/1 (NW) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/8 (YW) to battery voltage. See step 2 under CHECK.
3. Connectors C0606, C0642. See step 3 under CHECK.
4. O2 Sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/1 (NW) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/8 (YW) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0642. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. O2 Sensor No detail available for this fault.

1. Bank 2 downstream O2 sensor. See step 1 under CHECK.

1. Bank 2 Downstream O2 Sensor No detail available for this fault.

1. Bank 2 downstream O2 sensor. See step 1 under CHECK.

1. Bank 2 Downstream O2 Sensor No detail available for this fault.

1. Bank 2 downstream O2 sensor. See step 1 under CHECK.

1. Bank 2 Downstream O2 Sensor No detail available for this fault.

1. Short circuit C0606/8 (YW) - C0642/3 (YW). See step 1 under CHECK.
2. Connectors C0606, C0642. See step 2 under CHECK.
3. O2 Sensor. See step 3 under CHECK.

1. OPEN_CIRCUIT Short circuit C0606/8 (YW) - C0642/3 (YW). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0642. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. O2 Sensor No detail available for this fault.

1. Connector C0604, C0642. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Oxygen sensor. See step 3 under CHECK.

1. CONNECTOR Connector C0604, C0642. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Oxygen Sensor No detail available for this fault.

1. Fuel system leak. See step 1 under CHECK.
2. Injector leak. See step 2 under CHECK.
3. Fuel pressure regulation (3.5 Bar Maximum). See step 3 under CHECK.
4. Fuel pump. See step 4 under CHECK.

1. Fuel System Leak No detail available for this fault.
2. Injector Leak No detail available for this fault.
3. Fuel Pressure Regulation (3.5 Bar Maximum) No detail available for this fault.
4. Fuel Pump No detail available for this fault.

1. Injector leak. See step 1 under CHECK.
2. Fuel pressure regulation (3.5 Bar Maximum). See step 2 under CHECK.

1. Injector Leak No detail available for this fault.
2. Fuel Pressure Regulation (3.5 Bar Maximum) No detail available for this fault.

1. Fuel system leak. See step 1 under CHECK.
2. Injector leak. See step 2 under CHECK.
3. Fuel pressure regulation (3.5 Bar Maximum). See step 3 under CHECK.
4. Fuel pump. See step 4 under CHECK.

1. Fuel System Leak No detail available for this fault.
2. Injector Leak No detail available for this fault.
3. Fuel Pressure Regulation (3.5 Bar Maximum) No detail available for this fault.
4. Fuel Pump No detail available for this fault.

1. Injector leak. See step 1 under CHECK.
2. Fuel pressure regulation (3.5 Bar Maximum). See step 2 under CHECK.
3. Fuel pump. See step 3 under CHECK.

1. Injector Leak No detail available for this fault.
2. Fuel Pressure Regulation (3.5 Bar Maximum) No detail available for this fault.
3. Fuel Pump No detail available for this fault.

1. Open circuit C0606/41 (NW) - C0522/2 (NW). See step 1 under CHECK.
2. Connectors C0606, C0522. See step 2 under CHECK.
3. Injector cylinder 1. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/41 (NW) - C0522/2 (NW). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0522. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 1 No detail available for this fault.

1. Open circuit C0606/1 (NY) - C0523/2 (NY). See step 1 under CHECK.
2. Connectors C0606, C0523. See step 2 under CHECK.
3. Injector cylinder 2. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/1 (NY) - C0523/2 (NY). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0523. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 2 No detail available for this fault.

1. Open circuit C0606/2 (NG) - C0524/2 (NG). See step 1 under CHECK.
2. Connectors C0606, C0524. See step 2 under CHECK.
3. Injector cylinder 3. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/2 (NG) - C0524/2 (NG). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0524. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 3 No detail available for this fault.

1. Open circuit C0606/40 (NU) - C0525/2 (NU). See step 1 under CHECK.
2. Connectors C0606, C0525. See step 2 under CHECK.
3. Injector cylinder 4. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/40 (NU) - C0525/2 (NU). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0525. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 4 No detail available for this fault.

1. Open circuit C0606/26 (O) - C0526/2 (O). See step 1 under CHECK.
2. Connectors C0606, C0526. See step 2 under CHECK.
3. Injector cylinder 5. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/26 (O) - C0526/2 (O). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0526. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 5 No detail available for this fault.

1. Open circuit C0606/15 (NS) - C0527/2 (NS). See step 1 under CHECK.
2. Connectors C0606, C0527. See step 2 under CHECK.
3. Injector cylinder 6. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/15 (NS) - C0527/2 (NS). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0527. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 6 No detail available for this fault.

1. Open circuit C0606/14 (NR) - C0524/2 (NR). See step 1 under CHECK.
2. Connectors C0606, C0528. See step 2 under CHECK.
3. Injector cylinder 7. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/14 (NR) - C0524/2 (NR). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0528. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 7 No detail available for this fault.

1. Open circuit C0606/27 (NP) - C0529/2 (NP). See step 1 under CHECK.
2. Connectors C0606, C0529. See step 2 under CHECK.
3. Injector cylinder 8. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/27 (NP) - C0529/2 (NP). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0529. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 8 No detail available for this fault.

1. Harness integrity. See step 1 under CHECK.
2. Connectors C0331, C0787. See step 2 under CHECK.
3. Throttle Body. See step 3 under CHECK.

1. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Throttle Body No detail available for this fault.

1. Short circuit C0331/12 (UG) to ground. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Connectors C0331, C0787. See step 3 under CHECK.
4. Throttle Body. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/12 (UG) to ground. Check resistance < 5.0ohm.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Throttle Body No detail available for this fault.

1. Short circuit C0331/12 (UG) to battery voltage. See step 1 under CHECK.
2. Short circuit C0331/12 (UG) - 5V. See step 2 under CHECK.
3. Short circuit C0331/14 (YG) to battery voltage. See step 3 under CHECK.
4. Open circuit C0331/12 (UG) - C0787/2 (UG). See step 4 under CHECK.
5. Harness integrity. See step 5 under CHECK.
6. Connectors C0331, C0787. See step 6 under CHECK.
7. Throttle Body. See step 7 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/12 (UG) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0331/12 (UG) - 5V. Check resistance < 5.0ohm.
3. SHORT_CIRCUIT Short circuit C0331/14 (YG) to battery voltage. Check resistance < 5.0ohm.
4. OPEN_CIRCUIT Open circuit C0331/12 (UG) - C0787/2 (UG). Check resistance > 1Mohm.
5. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
6. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
7. Throttle Body No detail available for this fault.

1. Short circuit C0331/10 (BP) to ground. See step 1 under CHECK.
2. Connectors C0331, C2022. See step 2 under CHECK.
3. Fuel pump relay. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/10 (BP) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, C2022. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Fuel pump relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.

1. Short circuit C0331/10 (BP) to battery voltage. See step 1 under CHECK.
2. Connectors C0331, C2022. See step 2 under CHECK.
3. Fuel pump relay. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/10 (BP) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, C2022. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Fuel pump relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.

1. Open circuit C0331/10 (BP) - C2022/22 (BP). See step 1 under CHECK.
2. Connectors C0331, C2022. See step 2 under CHECK.
3. Fuel pump relay. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0331/10 (BP) - C2022/22 (BP). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0331, C2022. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Fuel pump relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.

1. Short circuit C0606/41 (NW) to ground. See step 1 under CHECK.
2. Connectors C0606, C0522. See step 2 under CHECK.
3. Injector cylinder 1. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/41 (NW) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0522. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 1 No detail available for this fault.

1. Short circuit C0606/41 (NW) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0522. See step 2 under CHECK.
3. Injector cylinder 1. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/41 (NW) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0522. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 1 No detail available for this fault.

1. Short circuit C0606/1 (NY) to ground. See step 1 under CHECK.
2. Connectors C0606, C0523. See step 2 under CHECK.
3. Injector cylinder 2. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/1 (NY) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0523. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 2 No detail available for this fault.

1. Short circuit C0606/1 (NY) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0523. See step 2 under CHECK.
3. Injector cylinder 2. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/1 (NY) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0523. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 2 No detail available for this fault.

1. Short circuit C0606/2 (NG) to ground. See step 1 under CHECK.
2. Connectors C0606, C0524. See step 2 under CHECK.
3. Injector cylinder 3. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/2 (NG) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0524. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 3 No detail available for this fault.

1. Short circuit C0606/2 (NG) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0524. See step 2 under CHECK.
3. Injector cylinder 3. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/2 (NG) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0524. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 3 No detail available for this fault.

1. Short circuit C0606/40 (NU) to ground. See step 1 under CHECK.
2. Injector cylinder 4. See step 2 under CHECK.
3. Connectors C0606, C0525. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/40 (NU) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0525. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 4 No detail available for this fault.

1. Short circuit C0606/40 (NU) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0525. See step 2 under CHECK.
3. Injector cylinder 4. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/40 (NU) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0525. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 4 No detail available for this fault.

1. Short circuit C0606/26 (O) to ground. See step 1 under CHECK.
2. Connectors C0606, C0526. See step 2 under CHECK.
3. Injector cylinder 5. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/26 (O) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0526. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 5 No detail available for this fault.

1. Short circuit C0606/26 (O) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0526. See step 2 under CHECK.
3. Injector cylinder 5. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/26 (O) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0526. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 5 No detail available for this fault.

1. Short circuit C0606/15 (NS) to ground. See step 1 under CHECK.
2. Connectors C0606, C0527. See step 2 under CHECK.
3. Injector cylinder 6. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/15 (NS) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0527. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 6 No detail available for this fault.

1. Short circuit C0606/15 (NS) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0527. See step 2 under CHECK.
3. Injector cylinder 6. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/15 (NS) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0527. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 6 No detail available for this fault.

1. Short circuit C0606/14 (NR) to ground. See step 1 under CHECK.
2. Connectors C0606, C0528. See step 2 under CHECK.
3. Injector cylinder 7. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/14 (NR) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0528. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 7 No detail available for this fault.

1. Short circuit C0606/14 (NR) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0528. See step 2 under CHECK.
3. Injector cylinder 7. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/14 (NR) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0528. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 7 No detail available for this fault.

1. Short circuit C0606/27 (NP) to ground. See step 1 under CHECK.
2. Connectors C0606, C0529. See step 2 under CHECK.
3. Injector cylinder 8. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/27 (NP) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0529. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 8 No detail available for this fault.

1. Short circuit C0606/27 (NP) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0529. See step 2 under CHECK.
3. Injector cylinder 8. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/27 (NP) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0529. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Injector Cylinder 8 No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Connectors C0606, C0626, C0627. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Knock sensor. See step 3 under CHECK.

1. CONNECTOR Connectors C0606, C0626, C0627. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Knock Sensor No detail available for this fault.

1. Connectors C0606, C0626, C0627. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Knock sensor. See step 3 under CHECK.

1. CONNECTOR Connectors C0606, C0626, C0627. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Knock Sensor No detail available for this fault.

1. Connectors C0606, C0626, C0627. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Knock sensor. See step 3 under CHECK.

1. CONNECTOR Connectors C0606, C0626, C0627. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Knock Sensor No detail available for this fault.

1. Open circuit C0606/49 (B) - C0626/01 (B). See step 1 under CHECK.
2. Short circuit C0606/49 (B) to ground. See step 2 under CHECK.
3. Connectors C0606, C0626. See step 3 under CHECK.
4. Knock sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Open circuit C0606/49 (B) - C0626/01 (B). Check resistance < 5.0ohm.
2. OPEN_CIRCUIT Short circuit C0606/49 (B) to ground. Check resistance > 1Mohm.
3. CONNECTOR Connectors C0606, C0626. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Knock Sensor No detail available for this fault.

1. Short circuit C0606/49 (B) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/49 (B) - 5 volts. See step 2 under CHECK.
3. Connectors C0606, C0626. See step 3 under CHECK.
4. Knock sensor loose. See step 4 under CHECK.
5. Mechanical noise from engine. See step 5 under CHECK.
6. Knock sensor. See step 6 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/49 (B) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/49 (B) - 5 volts. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0626. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Knock Sensor Loose No detail available for this fault.
5. Mechanical Noise From Engine No detail available for this fault.
6. Knock Sensor No detail available for this fault.

1. Open circuit C0606/50 (B) - C0627/01 (B). See step 1 under CHECK.
2. Short circuit C0606/50 (B) to ground. See step 2 under CHECK.
3. Connectors C0606, C0627. See step 3 under CHECK.
4. Knock sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Open circuit C0606/50 (B) - C0627/01 (B). Check resistance < 5.0ohm.
2. OPEN_CIRCUIT Short circuit C0606/50 (B) to ground. Check resistance > 1Mohm.
3. CONNECTOR Connectors C0606, C0627. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Knock Sensor No detail available for this fault.

1. Short circuit C0606/50 (B) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/50 (B) - 5 volts. See step 2 under CHECK.
3. Connectors C0606, C0627. See step 3 under CHECK.
4. Knock sensor loose. See step 4 under CHECK.
5. Mechanical noise from engine. See step 5 under CHECK.
6. Knock sensor. See step 6 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/50 (B) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/50 (B) - 5 volts. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0627. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Knock Sensor Loose No detail available for this fault.
5. Mechanical Noise From Engine No detail available for this fault.
6. Knock Sensor No detail available for this fault.

1. Connectors C0606, C1544. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Crankshaft sensor location. See step 3 under CHECK.
4. Crankshaft sensor. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C1544. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Crankshaft Sensor Location No detail available for this fault.
4. Crankshaft Sensor No detail available for this fault.

1. Camshaft sensor bank 1 location. See step 1 under CHECK.
2. Camshaft sensor bank 1. See step 2 under CHECK.

1. Camshaft Sensor Bank 1 Location No detail available for this fault.
2. Camshaft Sensor Bank 1 No detail available for this fault.

1. Short circuit C0606/20 (Y) to ground. See step 1 under CHECK.
2. Connectors C0606, C0176. See step 2 under CHECK.
3. Camshaft sensor bank 1. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/20 (Y) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0176. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Camshaft Sensor Bank 1 No detail available for this fault.

1. Short circuit C0606/20 (Y) to battery voltage. See step 1 under CHECK.
2. Open circuit C0606/20 (Y) - C0176/2 (Y). See step 2 under CHECK.
3. Connectors C0606, C0176. See step 3 under CHECK.
4. Camshaft sensor bank 1. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/20 (Y) to battery voltage. Check resistance < 5.0ohm.
2. OPEN_CIRCUIT Open circuit C0606/20 (Y) - C0176/2 (Y). Check resistance > 1Mohm.
3. CONNECTOR Connectors C0606, C0176. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Camshaft Sensor Bank 1 No detail available for this fault.

1. Camshaft sensor bank 2 location. See step 1 under CHECK.
2. Camshaft sensor bank 2. See step 2 under CHECK.

1. Camshaft Sensor Bank 2 Location No detail available for this fault.
2. Camshaft sensor bank 2 No detail available for this fault.

1. Short circuit C0606/18 (W) to ground. See step 1 under CHECK.
2. Connectors C0606, C1463. See step 2 under CHECK.
3. Camshaft sensor bank 2. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/18 (W) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C1463. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Camshaft Sensor Bank 2 No detail available for this fault.

1. Short circuit C0606/18 (W) to battery voltage. See step 1 under CHECK.
2. Open circuit C0606/18 (W) - C1463/2 (W). See step 2 under CHECK.
3. Connectors C0606, C1463. See step 3 under CHECK.
4. Camshaft sensor bank 2. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/18 (W) to battery voltage. Check resistance < 5.0ohm.
2. OPEN_CIRCUIT Open circuit C0606/18 (W) - C1463/2 (W). Check resistance > 1Mohm.
3. CONNECTOR Connectors C0606, C1463. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Camshaft Sensor Bank 2 No detail available for this fault.

1. Short circuit C0606/32,46 to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/32,46 to ground. See step 2 under CHECK.
3. Open circuit C0606/32 (Y) - C1544/1 (Y). See step 3 under CHECK.
4. Open circuit C0606/46 (Y) - C1544/2 (Y). See step 4 under CHECK.
5. Open Circuit Screen C0606/45. See step 5 under CHECK.
6. Connectors C0606, C1544. See step 6 under CHECK.
7. Magnetic contamination of crank sensor. See step 7 under CHECK.
8. Crank sensor. See step 8 under CHECK.
9. V8 Engine Management System ECM. See step 9 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/32,46 to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/32,46 to ground. Check resistance < 5.0ohm.
3. OPEN_CIRCUIT Open circuit C0606/32 (Y) - C1544/1 (Y). Check resistance > 1Mohm.
4. OPEN_CIRCUIT Open circuit C0606/46 (Y) - C1544/2 (Y). Check resistance > 1Mohm.
5. OPEN_CIRCUIT Open Circuit Screen C0606/45. Check resistance > 1Mohm.
6. CONNECTOR Connectors C0606, C1544. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
7. Magnetic Contamination Of Crank Sensor No detail available for this fault.
8. Crank Sensor No detail available for this fault.
9. V8 Engine Management System ECM No detail available for this fault.

1. Open circuit C0331/3 (NU) - C1886/4 (NU). See step 1 under CHECK.
2. Connectors C0331, C1886. See step 2 under CHECK.
3. Secondary air pump relay. See step 3 under CHECK.
4. Secondary air pump. See step 4 under CHECK.

1. OPEN_CIRCUIT Open circuit C0331/3 (NU) - C1886/4 (NU). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0331, C1886. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Secondary air pump relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
4. Secondary Air Pump No detail available for this fault.

1. Short circuit C0331/3 (NU) to battery voltage. See step 1 under CHECK.
2. Connectors C0331, C1886. See step 2 under CHECK.
3. Secondary air pump relay. See step 3 under CHECK.
4. Secondary air pump. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/3 (NU) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, C1886. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Secondary air pump relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
4. Secondary Air Pump No detail available for this fault.

1. Short circuit C0331/3 (NU) to ground. See step 1 under CHECK.
2. Connectors C0331, C1886. See step 2 under CHECK.
3. Secondary air pump relay. See step 3 under CHECK.
4. Secondary air pump. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/3 (NU) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, C1886. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Secondary air pump relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
4. Secondary Air Pump No detail available for this fault.

1. Open circuit C0331/3 (NU) - C1886/4 (NU). See step 1 under CHECK.
2. Connectors C0331, C1886. See step 2 under CHECK.
3. Secondary air pump relay. See step 3 under CHECK.
4. Secondary air pump. See step 4 under CHECK.

1. OPEN_CIRCUIT Open circuit C0331/3 (NU) - C1886/4 (NU). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0331, C1886. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Secondary air pump relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
4. Secondary Air Pump No detail available for this fault.

1. Oxygen sensor fault bank 1. See step 1 under CHECK.
2. Damaged/poisoned catalyst 1. See step 2 under CHECK.

1. Oxygen Sensor Fault Bank 1 There is a catalyst efficiency fault. Check the oxygen sensors on the same cylinder bank for faults. Only if there are no other faults present should the catalyst be changed.
2. Damaged/Poisoned Catalyst 1 There is a catalyst efficiency fault. Check the oxygen sensors on the same cylinder bank for faults. Only if there are no other faults present should the catalyst be changed.

1. Oxygen sensor fault bank 2. See step 1 under CHECK.
2. Damaged/poisoned catalyst bank 2. See step 2 under CHECK.

1. Oxygen Sensor Fault Bank 2 There is a catalyst efficiency fault. Check the oxygen sensors on the same cylinder bank for faults. Only if there are no other faults present should the catalyst be changed.
2. Damaged/Poisoned Catalyst Bank 2 There is a catalyst efficiency fault. Check the oxygen sensors on the same cylinder bank for faults. Only if there are no other faults present should the catalyst be changed.

1. Leak from purge system. There is a fault with the fuel tank breathing system. See step 1 under CHECK.

1. Leak From Purge System Check the following: Electrical connections to the purge valve. Purge valve is functioning correctly. Purge valve is opening and sealing correctly. Pipes for leaks and blockages.

1. Blockage in LDP system. See step 1 under CHECK.

1. Blockage In LDP System There is a fault with the leak detection system. A number of faults can occur with the leak detection system. Check for the following: CLAMPED TUBE Check electrical connections to the leak detection pump. Check the leak detection system for blocked tubes. Check that the leak detection pump is working correctly. FUEL VAPOR LEAKS Check the fuel vapor paths for leaks. A small leak is between 0.5 mm and 1.0 mm diameter. A large leak is greater than 1.0 mm in diameter.

1. Small fuel vapor leak. See step 1 under CHECK.

1. Small Fuel Vapor Leak There is a fault with the leak detection system. A number of faults can occur with the leak detection system. Check for the following: CLAMPED TUBE Check electrical connections to the leak detection pump. Check the leak detection system for blocked tubes. Check that the leak detection pump is working correctly. FUEL VAPOR LEAKS Check the fuel vapor paths for leaks. A small leak is between 0.5 mm and 1.0 mm in diameter. A large leak is greater than 1.0 mm in diameter.

1. Leak in fuel system vapor path. See step 1 under CHECK.

1. Leak In Fuel System Vapor Path Check the following: There is a fault with the leak detection system. A number of faults can occur with the leak detection system. CLAMPED TUBE Check electrical connections to the leak detection pump. Check the leak detection system for blocked tubes. Check that the leak detection pump is working correctly. FUEL VAPOR LEAKS Check the fuel vapor paths for leaks. A small leak is between 0.5 mm and 1.0 mm diameter. A large leak is greater than 1.0 mm in diameter.

1. Short circuit C0606/3 (N) - C0152/2 (N). See step 1 under CHECK.
2. Connectors C0606, C0152. See step 2 under CHECK.
3. Purge valve. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/3 (N) - C0152/2 (N). Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0152. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Purge Valve No detail available for this fault.

1. Short circuit C0606/3 (N) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0152. See step 2 under CHECK.
3. Purge valve. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/3 (N) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0152. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Purge Valve No detail available for this fault.

1. Short circuit C0606/3 (N) to ground. See step 1 under CHECK.
2. Connectors C0606, C0152. See step 2 under CHECK.
3. Purge valve. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/3 (N) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0152. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Purge Valve No detail available for this fault.

1. Large fuel vapor leak. See step 1 under CHECK.

1. Large Fuel Vapor Leak There is a fault with the leak detection system. A number of faults can occur with the leak detection system. Check for the following: CLAMPED TUBE Check electrical connections to the leak detection pump. Check the leak detection system for blocked tubes. Check that the leak detection pump is working correctly. FUEL VAPOR LEAKS Check the fuel vapor paths for leaks. A small leak is between 0.5 mm and 1.0 mm in diameter. A large leak is greater than 1.0 mm in diameter.

1. Leak in fuel system vapor path. See step 1 under CHECK.

1. Leak In Fuel System Vapor Path Check The Following: There is a fault with the leak detection system. A number of faults can occur with the leak detection system. CLAMPED TUBE Check electrical connections to the leak detection pump. Check the leak detection system for blocked tubes. Check that the leak detection pump is working correctly. FUEL VAPOR LEAKS Check the fuel vapor paths for leaks. A small leak is between 0.5 mm and 1.0 mm in diameter. A large leak is greater than 1.0 mm in diameter.

1. Leak in fuel system vapor path. See step 1 under CHECK.

1. Leak In Fuel System Vapor Path Check The Following: There is a fault with the leak detection system. A number of faults can occur with the leak detection system. CLAMPED TUBE Check electrical connections to the leak detection pump. Check the leak detection system for blocked tubes. Check that the leak detection pump is working correctly. FUEL VAPOR LEAKS Check the fuel vapor paths for leaks. A small leak is between 0.5 mm and 1.0 mm diameter. A large leak is greater than 1.0 mm in diameter.

1. Low secondary air flow to bank 1. See step 1 under CHECK.

1. Low Secondary Air Flow To Bank 1 There is low secondary air flow to one of the cylinder banks. Check the following: Electrical connections between the relay and the pump. Secondary air pump is functioning correctly. Secondary air valve is opening and sealing correctly. Secondary air pipes for leaks and blockages.

1. Low secondary air flow to bank 2. See step 1 under CHECK.

1. Low Secondary Air Flow To Bank 2 There is low secondary air flow to one of the cylinder banks. Check the following: Electrical connections between the relay and the pump. Secondary air pump is functioning correctly. Secondary air valve is opening and sealing correctly. Secondary air pipes for leaks and blockages.

1. Connector C0331, C0862. See step 1 under CHECK.
2. ABS/traction control fault. See step 2 under CHECK.

1. CONNECTOR Connector C0331, C0862. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. ABS/Traction Control Fault No detail available for this fault.

1. Ignition. See step 1 under CHECK.
2. Fuelling. See step 2 under CHECK.
3. Engine mechanical behavior. See step 3 under CHECK.

1. Ignition The following items must be verified and action taken before replacing the throttle body. Check the following: ECU FAULTS Check if there are any ECU system faults, and correct them. A complete fault free cycle (apart from the current error) must be done before continuing. UNSATISFACTORY ENGINE BEHAVIOR Check the spark plugs and replace as necessary. Check the ignition coils and replace as necessary. Check any other obvious components and replace as necessary. THROTTLE BODY REPLACEMENT Check a complete fault free cycle (apart from the current error) has been done. Check the engine is running smoothly at idle speed. If both these are OK, and the fault is still present, then replace the throttle body.
2. Fuelling The following items must be verified and action taken before replacing the throttle body. Check the following: ECU FAULTS Check if there are any ECU system faults, and correct them. A complete fault free cycle (apart from the current error) must be done before continuing. UNSATISFACTORY ENGINE BEHAVIOR Check the spark plugs and replace as necessary. Check the ignition coils and replace as necessary. Check any other obvious components and replace as necessary. THROTTLE BODY REPLACEMENT Check a complete fault free cycle (apart from the current error) has been done. Check the engine is running smoothly at idle speed. If both these are OK, and the fault is still present, then replace the throttle body.
3. Engine Mechanical Behavior The following items must be verified and action taken before replacing the throttle body. Check The Following: ECU FAULTS Check if there are any ECU system faults, and correct them. A complete fault free cycle (apart from the current error) must be done before continuing. UNSATISFACTORY ENGINE BEHAVIOR Check the spark plugs and replace as necessary. Check the ignition coils and replace as necessary. Check any other obvious components and replace as necessary. THROTTLE BODY REPLACEMENT Check a complete fault free cycle (apart from the current error) has been done. Check the engine is running smoothly at idle speed. If both these are OK, and the fault is still present, then replace the throttle body.

1. Ignition. See step 1 under CHECK.
2. Fuelling. See step 2 under CHECK.
3. Engine mechanical behavior. See step 3 under CHECK.
4. Throttle body. See step 4 under CHECK.

1. Ignition The following items must be verified and action taken before replacing the throttle body. Check the following: ECU FAULTS Check if there are any ECU system faults, and correct them. A complete fault free cycle (apart from the current error) must be done before continuing. UNSATISFACTORY ENGINE BEHAVIOR Check the spark plugs and replace as necessary. Check the ignition coils and replace as necessary. Check any other obvious components and replace as necessary. THROTTLE BODY REPLACEMENT Check a complete fault free cycle (apart from the current error) has been done. Check the engine is running smoothly at idle speed. If both these are OK, and the fault is still present, then replace the throttle body.
2. Fuelling The following items must be verified and action taken before replacing the throttle body. Check The Following: ECU FAULTS Check if there are any ECU system faults, and correct them. A complete fault free cycle (apart from the current error) must be done before continuing. UNSATISFACTORY ENGINE BEHAVIOR Check the spark plugs and replace as necessary. Check the ignition coils and replace as necessary. Check any other obvious components and replace as necessary. THROTTLE BODY REPLACEMENT Check a complete fault free cycle (apart from the current error) has been done. Check the engine is running smoothly at idle speed. If both these are OK, and the fault is still present, then replace the throttle body.
3. Engine Mechanical Behavior The following items must be verified and action taken before replacing the throttle body. Check the following: ECU FAULTS Check if there are any ECU system faults, and correct them. A complete fault free cycle (apart from the current error) must be done before continuing. UNSATISFACTORY ENGINE BEHAVIOR Check the spark plugs and replace as necessary. Check the ignition coils and replace as necessary. Check any other obvious components and replace as necessary. THROTTLE BODY REPLACEMENT Check a complete fault free cycle (apart from the current error) has been done. Check the engine is running smoothly at idle speed. If both these are OK, and the fault is still present, then replace the throttle body.
4. Throttle Body The following items must be verified and action taken before replacing the throttle body. Check The Following: ECU FAULTS Check if there are any ECU system faults, and correct them. A complete fault free cycle (apart from the current error) must be done before continuing. UNSATISFACTORY ENGINE BEHAVIOR Check the spark plugs and replace as necessary. Check the ignition coils and replace as necessary. Check any other obvious components and replace as necessary. THROTTLE BODY REPLACEMENT Check a complete fault free cycle (apart from the current error) has been done. Check the engine is running smoothly at idle speed. If both these are OK, and the fault is still present, then replace the throttle body.

1. Connectors C0606, C0179. See step 1 under CHECK.
2. Starter motor relay. See step 2 under CHECK.
3. Starter motor. See step 3 under CHECK.

1. CONNECTOR Connectors C0606, C0179. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. RELAY Starter motor relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
3. Starter Motor No detail available for this fault.

1. Connectors C0606, C0179. See step 1 under CHECK.
2. Starter motor relay. See step 2 under CHECK.
3. Starter motor. See step 3 under CHECK.

1. CONNECTOR Connectors C0606, C0179. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. RELAY Starter motor relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
3. Starter Motor No detail available for this fault.

1. Connectors C0606, C0179. See step 1 under CHECK.
2. Starter motor relay. See step 2 under CHECK.
3. Starter motor. See step 3 under CHECK.

1. CONNECTOR Connectors C0606, C0179. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. RELAY Starter motor relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
3. Starter Motor No detail available for this fault.

1. Open circuit C0331/29 (BG) - C1629/17 (BG). See step 1 under CHECK.
2. Connectors C0331, C1629. See step 2 under CHECK.
3. Air conditioning system fault. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0331/29 (BG) - C1629/17 (BG). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0331, C1629. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Air Conditioning System Fault There is an air conditioning fault. Check the air conditioning system for faults.

1. Short circuit C0331/29 (BG) to ground. See step 1 under CHECK.
2. Connectors C0331, C1629. See step 2 under CHECK.
3. Air conditioning system fault. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/29 (BG) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, C1629. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Air Conditioning System Fault There is an air conditioning fault. Check the air conditioning system for faults.

1. Short circuit C0331/29 (BG) to battery voltage. See step 1 under CHECK.
2. Connectors C0331, C1629. See step 2 under CHECK.
3. Air conditioning system fault. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/29 (BG) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, C1629. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Air Conditioning System Fault There is an air conditioning fault. Check the air conditioning system for faults.

1. Jump start with incorrect type of battery. See step 1 under CHECK.

1. Jump Started With Incorrect Type Of Battery No detail available for this fault.

1. Low battery volts. See step 1 under CHECK.

1. OPEN_CIRCUIT Low battery volts. Check resistance > 1Mohm.

1. Battery supply short circuit to ground. See step 1 under CHECK.

1. SHORT_CIRCUIT Battery supply short circuit to ground. Check resistance < 5.0ohm.

1. Short circuit C0331/24, 28 to battery voltage. See step 1 under CHECK.
2. Short circuit C0331/24 (UR) to ground. See step 2 under CHECK.
3. Open circuit C0331/24 (UR) - C0075/4 (UR). See step 3 under CHECK.
4. Open circuit C0331/28 (NS) - C0075/3 (NS). See step 4 under CHECK.
5. Connectors C0331, C0075. See step 5 under CHECK.
6. Brake Switch. See step 6 under CHECK.
7. V8 Engine Management System ECM. See step 7 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/24,28 to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0331/24 (UR) to ground. Check resistance < 5.0ohm.
3. OPEN_CIRCUIT Open circuit C0331/24 (UR) - C0075/4 (UR). Check resistance > 1Mohm.
4. OPEN_CIRCUIT Open circuit C0331/28 (NS) - C0075/3 (NS). Check resistance > 1Mohm.
5. CONNECTOR Connectors C0331, C0075. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
6. Brake Switch Check for open/short circuit with switch open/closed.
7. V8 Engine Management System ECM No detail available for this fault.

1. V8 Engine Management System ECM. See step 1 under CHECK.

1. V8 Engine Management System ECM No detail available for this fault.

1. V8 Engine Management System ECM. See step 1 under CHECK.

1. V8 Engine Management System ECM No detail available for this fault.

1. V8 Engine Management System ECM. See step 1 under CHECK.

1. V8 Engine Management System ECM No detail available for this fault.

1. Open circuit C0606/12 (BG) - C0179/1 (BG). See step 1 under CHECK.
2. Connectors C0606, C0179. See step 2 under CHECK.
3. Starter motor relay. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/12 (BG) - C0179/1 (BG). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0179. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Starter motor relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.

1. Short circuit C0606/12 (BG) to ground. See step 1 under CHECK.
2. Connectors C0606, C0179. See step 2 under CHECK.
3. Starter motor relay. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/12 (BG) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0179. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Starter motor relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.

1. Short circuit C0606/12 (BG) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0179. See step 2 under CHECK.
3. Starter motor relay. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/12 (BG) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0179. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Starter motor relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.

1. Connectors C0606, C1544. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Crankshaft sensor location. See step 3 under CHECK.
4. Crankshaft sensor. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C1544. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Crankshaft Sensor Location No detail available for this fault.
4. Crankshaft Sensor No detail available for this fault.

1. Connectors C0606, C1544. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Crankshaft sensor location. See step 3 under CHECK.
4. Crankshaft sensor. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C1544. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Crankshaft Sensor Location No detail available for this fault.
4. Crankshaft Sensor No detail available for this fault.

1. Connectors C0606, C1544. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Crankshaft sensor location. See step 3 under CHECK.
4. Crankshaft sensor. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C1544. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Crankshaft Sensor Location No detail available for this fault.
4. Crankshaft Sensor No detail available for this fault.

1. Short circuit C0331/4 (BG) to ground. See step 1 under CHECK.
2. Connectors C0606, C0005, fan control module connector. See step 2 under CHECK.
3. Fan control module. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/4 (BG) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0005, fan control module connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Fan Control Module No detail available for this fault.

1. Short circuit C0331/4 (BG) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0005, Fan control module connector. See step 2 under CHECK.
3. Fan control module. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/4 (BG) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0005, fan control module connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Fan Control Module No detail available for this fault.

1. Open circuit C0331/4 (BG) - Fan control module connector. See step 1 under CHECK.
2. Connectors C0606, C0005, fan control module connector. See step 2 under CHECK.
3. Fan control module. See step 3 under CHECK.

1. SHORT_CIRCUIT Open circuit C0331/4 (BG) - fan control module connector. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0005, fan control module connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Fan Control Module No detail available for this fault.

Description

1. DTC P0702 Internal FET Fault: Open Circuit
2. DTC P0702 Internal FET Fault: Short Circuit To Battery
3. DTC P0702 Internal FET Fault: Short Circuit To Ground

1. Electronic Automatic Transmission ECU. See step 1 under CHECK.

1. Electronic Automatic Transmission ECU No detail available for this fault.

1. Connectors C1835, C1452. See step 1 under CHECK.
2. Circuit integrity C1835/34 (B) - C1452/1 (B). See step 2 under CHECK.
3. Circuit integrity C1835/24 (O) - C1452/2 (O). See step 3 under CHECK.
4. Circuit integrity C1835/14 (P) - C1452/3 (P). See step 4 under CHECK.
5. Circuit integrity C1835/4 (Y) - C1452/4 (Y). See step 5 under CHECK.
6. Circuit integrity C1835/31 (G) - C1452/5 (G). See step 6 under CHECK.
7. Gearbox Gear Selector Switch. See step 7 under CHECK.
8. Electronic Automatic Transmission ECU. See step 8 under CHECK.

1. CONNECTOR Connectors C1835, C1452. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/34 (B) - C1452/1 (B). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/24 (O) - C1452/2 (O). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. CIRCUIT_INTEGRITY Circuit integrity C1835/14 (P) - C1452/3 (P). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
5. CIRCUIT_INTEGRITY Circuit integrity C1835/4 (Y) - C1452/4 (Y). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
6. CIRCUIT_INTEGRITY Circuit integrity C1835/31 (G) - C1452/5 (G). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
7. Gearbox Gear Selector Switch Check the following: Check the state of each gear switch input against each gear position against the following table. Each entry in the table states, for each gear position, the expected connectivity between the common line, C1452/5, and each gear switch line. GEARBOX GEAR SELECTOR SWITCH TESTING (1) Gear Switch Line/Connector/Pin No. P R N D L1/C1452/1 SC OC SC OC L2/C1452/2 SC OC SC OC L3/C1452/3 SC SC OC OC L4/C1452/4 OC SC SC SC (1) PASS VALUES: Short circuit (SC) less than 2.0 Ohms. Open circuit (OC) greater than 2.0 Ohms.
8. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P0710 Gearbox Oil Temperature Sensor Fault: Plausibility Fault
2. DTC P0711 Gearbox Oil Temperature Sensor Fault: General Fault
3. DTC P0711 Gearbox Oil Temperature Sensor Fault: Open Circuit
4. DTC P0712 Gearbox Oil Temperature Sensor Fault: Short Circuit To Ground
5. DTC P0713 Gearbox Oil Temperature Sensor Fault: Short Circuit To Battery

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/22 (BR) - C0244/13 (BR). See step 2 under CHECK.
3. Circuit integrity C1835/12 (WR) - C0244/14 (WR). See step 3 under CHECK.
4. Gearbox Oil Temperature Sensor. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/22 (BR) - C0244/13 (BR). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/12 (WR) - C0244/14 (WR). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Oil Temperature Sensor No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. Severe overload of vehicle. See step 1 under CHECK.
2. Major gearbox internal fault. See step 2 under CHECK.
3. Gearbox oil overfill. See step 3 under CHECK.

1. Severe Overload Of Vehicle No detail available for this fault.
2. Major Gearbox Internal Fault No detail available for this fault.
3. Gearbox Oil Overfill No detail available for this fault.

1. DTC P0715 Turbine Speed Sensor Fault: Plausibility Fault
2. DTC P0716 Turbine Speed Sensor Fault: Value Is Too High

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/23 (U) - C0244/5 (U). See step 2 under CHECK.
3. Circuit integrity C1835/33 (S) - C0244/6 (S). See step 3 under CHECK.
4. Gearbox Turbine Speed Sensor. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/23 (U) - C0244/5 (U). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/33 (S) - C0244/6 (S). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Turbine Speed Sensor No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P0720 Output Shaft Speed Sensor Fault: Plausibility Fault
2. DTC P0721 Output Shaft Speed Sensor Fault: Value Is Too High

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/13 (W) - C0244/1 (W). See step 2 under CHECK.
3. Circuit integrity C1835/3 (N) - C0244/10 (N). See step 3 under CHECK.
4. Gearbox Output Shaft Speed Sensor. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/13 (W) - C0244/1 (W). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/3 (N) - C0244/10 (N). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Output Shaft Speed Sensor No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. Gearbox mechanical fault. See step 1 under CHECK.
2. CAN bus. See step 2 under CHECK.

1. Gearbox Mechanical Fault No detail available for this fault.
2. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. Transmission Damage (Defective Clutch). See step 1 under CHECK.

1. Transmission Damage (Defective Clutch) No detail available for this fault.

1. Gearbox mechanical fault. See step 1 under CHECK.
2. CAN bus. See step 2 under CHECK.

1. Gearbox Mechanical Fault No detail available for this fault.
2. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. Gearbox mechanical fault. See step 1 under CHECK.
2. CAN bus. See step 2 under CHECK.

1. Gearbox Mechanical Fault No detail available for this fault.
2. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. Gearbox mechanical fault. See step 1 under CHECK.
2. CAN bus. See step 2 under CHECK.

1. Gearbox Mechanical Fault No detail available for this fault.
2. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. Gearbox mechanical fault. See step 1 under CHECK.
2. CAN bus. See step 2 under CHECK.

1. Gearbox Mechanical Fault No detail available for this fault.
2. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. Gearbox mechanical fault. See step 1 under CHECK.
2. CAN bus. See step 2 under CHECK.

1. Gearbox Mechanical Fault No detail available for this fault.
2. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/23 (U) - C0244/5 (U). See step 2 under CHECK.
3. Circuit integrity C1835/33 (S) - C0244/6 (S). See step 3 under CHECK.
4. Gearbox Turbine Speed Sensor. See step 4 under CHECK.
5. Torque Converter Clutch. See step 5 under CHECK.
6. Electronic Automatic Transmission ECU. See step 6 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/23 (U) - C0244/5 (U). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/33 (S) - C0244/6 (S). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Turbine Speed Sensor No detail available for this fault.
5. Torque Converter Clutch No detail available for this fault.
6. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P0740 Pressure Line Solenoid 4 Fault: Plausibility Fault
2. DTC P0743 Pressure Line Solenoid 4 Fault: General Fault
3. DTC P0743 Pressure Line Solenoid 4 Fault: Short Circuit To Battery
4. DTC P0743 Pressure Line Solenoid 4 Fault: Short Circuit To Ground Or Open Circuit

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/11 (P) - C0244/12 (P). See step 2 under CHECK.
3. Circuit integrity C1835/7 (TB) - C0244/11 (TB). See step 3 under CHECK.
4. Gearbox Pressure Line Solenoid (EDS) 4. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/11 (P) - C0244/12 (P). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/7 (TB) - C0244/11 (TB). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Pressure Line Solenoid (EDS) 4 No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P0745 Pressure Line Solenoid 1 Fault: Plausibility Fault
2. DTC P0748 Pressure Line Solenoid 1 Fault: General Fault
3. DTC P0748 Pressure Line Solenoid 1 Fault: Short Circuit To Battery
4. DTC P0748 Pressure Line Solenoid 1 Fault: Short Circuit To Ground Or Open Circuit

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/11 (P) - C0244/12 (P). See step 2 under CHECK.
3. Circuit integrity C1835/28 (R) - C0244/2 (R). See step 3 under CHECK.
4. Gearbox Pressure Line Solenoid (EDS) 1. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/11 (P) - C0244/12 (P). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/28 (R) - C0244/2 (R). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Pressure Line Solenoid (EDS) 1 No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P0750 Shift Solenoid 1 Fault: Plausibility Fault
2. DTC P0751 Shift Solenoid 1 Fault: Open Circuit
3. DTC P0752 Shift Solenoid 1 Fault: Short Circuit To Ground
4. DTC P0753 Shift Solenoid 1 Fault: Short Circuit To Battery

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/21 (YU) - C0244/16 (YU). See step 2 under CHECK.
3. Circuit integrity C1835/38 (O) - C0244/8 (O). See step 3 under CHECK.
4. Gearbox Shift Solenoid (MV) 1. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/21 (YU) - C0244/16 (YU). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/38 (O) - C0244/8 (O). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Shift Solenoid (MV) 1 No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P0755 Shift Solenoid 2 Fault: Plausibility Fault
2. DTC P0756 Shift Solenoid 2 Fault: Open Circuit
3. DTC P0757 Shift Solenoid 2 Fault: Short Circuit To Ground
4. DTC P0758 Shift Solenoid 2 Fault: Short Circuit To Battery

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/21 (YU) - C0244/16 (YU). See step 2 under CHECK.
3. Circuit integrity C1835/26 (G) - C0244/9 (G). See step 3 under CHECK.
4. Gearbox: Shift Solenoid (MV) 2. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/21 (YU) - C0244/16 (YU). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/26 (G) - C0244/9 (G). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox: Shift Solenoid (MV) 2 No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P0760 Shift Solenoid 3 Fault: Plausibility Fault
2. DTC P0761 Shift Solenoid 3 Fault: Open Circuit
3. DTC P0762 Shift Solenoid 3 Fault: Short Circuit To Ground
4. DTC P0763 Shift Solenoid 3 Fault: Short Circuit To Battery

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/21 (YU) - C0244/16 (YU). See step 2 under CHECK.
3. Circuit integrity C1835/16 (Y) - C0244/4 (Y). See step 3 under CHECK.
4. Gearbox Shift Solenoid (MV) 3. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/21 (YU) - C0244/16 (YU). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/16 (Y) - C0244/4 (Y). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Shift Solenoid (MV) 3 No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P0775 Pressure Line Solenoid 2 Fault: Plausibility Fault
2. DTC P0778 Pressure Line Solenoid 2 Fault: General Fault
3. DTC P0778 Pressure Line Solenoid 2 Fault: Short Circuit To Battery
4. DTC P0778 Pressure Line Solenoid 2 Fault: Short Circuit To Ground Or Open Circuit

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/11 (P) - C0244/12 (P). See step 2 under CHECK.
3. Circuit integrity C1835/27 (B) - C0244/3 (B). See step 3 under CHECK.
4. Gearbox Pressure Line Solenoid (EDS) 2. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/11 (P) - C0244/12 (P). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/27 (B) - C0244/3 (B). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Pressure Line Solenoid (EDS) 2 No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P0780 Controlled Load Transfer Fault: Value Is Too High
2. DTC P0780 Controlled Load Transfer Fault: Value Has Not Changed

1. Gearbox mechanical fault. See step 1 under CHECK.
2. CAN bus. See step 2 under CHECK.

1. Gearbox Mechanical Fault No detail available for this fault.
2. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. DTC P0782 Controlled Load Transfer 2/3 Fault: Value Has Not Changed
2. DTC P0782 Controlled Load Transfer 2/3 Fault: Value Is Too High

1. Gearbox mechanical fault. See step 1 under CHECK.
2. CAN bus. See step 2 under CHECK.

1. Gearbox Mechanical Fault No detail available for this fault.
2. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. DTC P0783 Controlled Load Transfer 3/4 Fault: Value Has Not Changed
2. DTC P0783 Controlled Load Transfer 3/4 Fault: Value Is Too High

1. Gearbox mechanical fault. See step 1 under CHECK.
2. CAN bus. See step 2 under CHECK.

1. Gearbox Mechanical Fault No detail available for this fault
2. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. DTC P0795 Pressure Line Solenoid 3 Fault: Plausibility Fault
2. DTC P0798 Pressure Line Solenoid 3 Fault: General Fault
3. DTC P0798 Pressure Line Solenoid 3 Fault: Short Circuit To Battery
4. DTC P0798 Pressure Line Solenoid 3 Fault: Short Circuit To Ground Or Open Circuit

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/11 (P) - C0244/12 (P). See step 2 under CHECK.
3. Circuit integrity C1835/17 (K) - C0244/7 (K). See step 3 under CHECK.
4. Gearbox Pressure Line Solenoid (EDS) 3. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/11 (P) - C0244/12 (P). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/17 (K) - C0244/7 (K). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Pressure Line Solenoid (EDS) 3 No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. Air mass to load adaption too large. See step 1 under CHECK.

1. Air Mass To Load Adaption Too Large No detail available for this fault.

1. Air mass to load adaption too small. See step 1 under CHECK.

1. Air Mass To Load Adaption Too Small No detail available for this fault.

1. Instrument pack indicates ambient temperature sensor fault. See step 1 under CHECK.

1. Instrument Pack Indicates Ambient Temperature Sensor Fault A fault has been indicated by the instrument pack. Use the instrument pack diagnostics to diagnose this fault.

1. Connectors C0331, C2348. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Radiator outlet temperature sensor. See step 3 under CHECK.
4. Engine not warming up properly. See step 4 under CHECK.

1. CONNECTOR Connectors C0331, C2348. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Radiator Outlet Temperature Sensor No detail available for this fault.
4. Engine Not Warming Up Properly No detail available for this fault.

1. Connectors C0331, C2348. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Radiator outlet temperature sensor. See step 3 under CHECK.
4. Engine not warming up properly. See step 4 under CHECK.

1. CONNECTOR Connectors C0331, C2348. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Radiator Outlet Temperature Sensor No detail available for this fault.
4. Engine Not Warming Up Properly No detail available for this fault.

1. Throttle is in limp home mode. See step 1 under CHECK.

1. Throttle Is In Limp Home Mode No detail available for this fault.

1. Harness integrity. See step 1 under CHECK.
2. Connectors C0606, C0787. See step 2 under CHECK.
3. Throttle pedal sensor. See step 3 under CHECK.

1. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CONNECTOR Connectors C0606, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Throttle Pedal Sensor No detail available for this fault.

1. Open circuit C0331/8 (W) - C0787/4 (W). See step 1 under CHECK.
2. Open circuit C0331/9 (Y) - C0787/5 (Y). See step 2 under CHECK.
3. Short circuit C0331/9 (Y) to ground. See step 3 under CHECK.
4. Connectors C0331, C0787. See step 4 under CHECK.
5. Throttle pedal sensor. See step 5 under CHECK.

1. OPEN_CIRCUIT Open circuit C0331/8 (W) - C0787/4 (W). Check resistance > 1Mohm.
2. SHORT_CIRCUIT Open circuit C0331/9 (Y) - C0787/5 (Y). Check resistance < 5.0ohm.
3. SHORT_CIRCUIT Short circuit C0331/9 (Y) to ground. Check resistance < 5.0ohm.
4. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
5. Throttle Pedal Sensor No detail available for this fault.

1. Short circuit C0331/8 (W) - 5 volts. See step 1 under CHECK.
2. Short circuit C0331/8 (W) to battery voltage. See step 2 under CHECK.
3. Connectors C0331, C0787. See step 3 under CHECK.
4. Throttle pedal sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/8 (W) - 5 volts. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0331/8 (W) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Throttle Pedal Sensor No detail available for this fault.

1. Incorrect harness installation to rear O2 sensors. See step 1 under CHECK.

1. Incorrect Harness Installation To Rear O2 Sensors No detail available for this fault.

1. Air leak to inlet bank 1. See step 1 under CHECK.
2. Air leak to exhaust bank 1. See step 2 under CHECK.

1. Air Leak To Inlet Bank 1 The ECM is unable to maintain the lambda correction. Check for air leak paths into the exhaust before the rear O2 sensor. Check for air leak paths into the inlet manifold after the air mass flow meter.
2. Air Leak To Exhaust Bank 1 The ECM is unable to maintain the lambda correction. Check for air leak paths into the exhaust before the rear O2 sensor. Check for air leak paths into the inlet manifold after the air mass flow meter.

1. Air leak to inlet bank 1. See step 1 under CHECK.
2. Air leak to exhaust bank 1. See step 2 under CHECK.

1. Air Leak To Inlet Bank 1 The ECM is unable to maintain the lambda correction. Check for air leak paths into the exhaust before the rear O2 sensor. Check for air leak paths into the inlet manifold after the air mass flow meter.
2. Air Leak To Exhaust Bank 1 The ECM is unable to maintain the lambda correction. Check for air leak paths into the exhaust before the rear O2 sensor. Check for air leak paths into the inlet manifold after the air mass flow meter.

1. Air leak to inlet bank 2. See step 1 under CHECK.
2. Air leak to exhaust bank 2. See step 2 under CHECK.

1. Air Leak To Inlet Bank 2 The ECM is unable to maintain the lambda correction. Check for air leak paths into the exhaust before the rear O2 sensor. Check for air leak paths into the inlet manifold after the air mass flow meter.
2. Air Leak To Exhaust Bank 2 The ECM is unable to maintain the lambda correction. Check for air leak paths into the exhaust before the rear O2 sensor. Check for air leak paths into the inlet manifold after the air mass flow meter.

1. Air leak to inlet bank 2. See step 1 under CHECK.
2. Air leak to exhaust bank 2. See step 2 under CHECK.

1. Air Leak To Inlet Bank 2 The ECM is unable to maintain the lambda correction. Check for air leak paths into the exhaust before the rear O2 sensor. Check for air leak paths into the inlet manifold after the air mass flow meter.
2. Air Leak To Exhaust Bank 2 The ECM is unable to maintain the lambda correction. Check for air leak paths into the exhaust before the rear O2 sensor. Check for air leak paths into the inlet manifold after the air mass flow meter.

1. Harness integrity. See step 1 under CHECK.
2. Connectors C0606, C0787. See step 2 under CHECK.
3. Throttle pedal sensor. See step 3 under CHECK.

1. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CONNECTOR Connectors C0606, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Throttle Pedal Sensor No detail available for this fault.

1. Open circuit C0331/13 (WG) - C0787/6 (WG). See step 1 under CHECK.
2. Open circuit C0331/14 (YG) - C0787/3 (YG). See step 2 under CHECK.
3. Short circuit C0331/14 (YG) to ground. See step 3 under CHECK.
4. Connectors C0331, C0787. See step 4 under CHECK.
5. Throttle pedal sensor. See step 5 under CHECK.

1. OPEN_CIRCUIT Open circuit C0331/13 (WG) - C0787/6 (WG). Check resistance > 1Mohm.
2. SHORT_CIRCUIT Open circuit C0331/14 (YG) - C0787/3 (YG). Check resistance < 5.0ohm.
3. SHORT_CIRCUIT Short circuit C0331/14 (YG) to ground. Check resistance < 5.0ohm.
4. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
5. Throttle Pedal Sensor No detail available for this fault.

1. Short circuit C0331/13 (WG) - 5 volts. See step 1 under CHECK.
2. Short circuit C0331/13 (WG) to battery voltage. See step 2 under CHECK.
3. Connectors C0331, C0787. See step 3 under CHECK.
4. Throttle pedal sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/13 (WG) - 5 volts. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0331/13 (WG) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0331, C0787. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Throttle Pedal Sensor No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Fuel system. See step 1 under CHECK.
2. Ignition components. See step 2 under CHECK.
3. Engine mechanical performance. See step 3 under CHECK.

1. Fuel System No detail available for this fault.
2. Ignition Components No detail available for this fault.
3. Engine Mechanical Performance No detail available for this fault.

1. Open circuit C0606/36 (B) - C0626/03 (B). See step 1 under CHECK.
2. Short circuit C0606/36 (B) to ground. See step 2 under CHECK.
3. Connectors C0606, C0626. See step 3 under CHECK.
4. Knock sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Open circuit C0606/36 (B) - C0626/03 (B). Check resistance < 5.0ohm.
2. OPEN_CIRCUIT Short circuit C0606/36 (B) to ground. Check resistance > 1Mohm.
3. CONNECTOR Connectors C0606, C0626. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Knock Sensor No detail available for this fault.

1. Short circuit C0606/36 (B) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/36 (B) - 5 volts See step 2 under CHECK.
3. Connectors C0606, C0626. See step 3 under CHECK.
4. Knock sensor loose. See step 4 under CHECK.
5. Mechanical noise from engine. See step 5 under CHECK.
6. Knock sensor. See step 6 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/36 (B) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/36 (B) - 5 volts. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0626. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Knock Sensor Loose No detail available for this fault.
5. Mechanical Noise From Engine No detail available for this fault.
6. Knock Sensor No detail available for this fault.

1. Open circuit C0606/37 (B) - C0627/01 (B). See step 1 under CHECK.
2. Short circuit C0606/37 (B) to ground. See step 2 under CHECK.
3. Connectors C0606, C0627. See step 3 under CHECK.
4. Knock sensor. See step 4 under CHECK.

1. SHORT_CIRCUIT Open circuit C0606/37 (B) - C0627/01 (B). Check resistance < 5.0ohm.
2. OPEN_CIRCUIT Short circuit C0606/37 (B) to ground. Check resistance > 1Mohm.
3. CONNECTOR Connectors C0606, C0627. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Knock Sensor No detail available for this fault.

1. Short circuit C0606/37 (B) to battery voltage. See step 1 under CHECK.
2. Short circuit C0606/37 (B) - 5 volts. See step 2 under CHECK.
3. Connectors C0606, C0627. See step 3 under CHECK.
4. Knock sensor loose. See step 4 under CHECK.
5. Mechanical noise from engine. See step 5 under CHECK.
6. Knock sensor. See step 6 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/37 (B) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0606/37 (B) - 5 volts. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0627. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Knock Sensor Loose No detail available for this fault.
5. Mechanical Noise From Engine No detail available for this fault.
6. Knock Sensor No detail available for this fault.

1. Short circuit C0331/3 (NU) to ground. See step 1 under CHECK.
2. Connectors C0331, C1886. See step 2 under CHECK.
3. Secondary air pump relay. See step 3 under CHECK.
4. Secondary air pump. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/3 (NU) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, C1886. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Secondary air pump relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
4. Secondary Air Pump No detail available for this fault

1. Short circuit C0331/3 (NU) to battery voltage. See step 1 under CHECK.
2. Connectors C0331, C1886. See step 2 under CHECK.
3. Secondary air pump relay. See step 3 under CHECK.
4. Secondary air pump. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/3 (NU) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, C1886. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. RELAY Secondary air pump relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
4. Secondary Air Pump No detail available for this fault.

1. DM-TL Module. See step 1 under CHECK.

1. DM-TL Module No detail available for this fault.

1. DM-TL Module. See step 1 under CHECK.

1. DM-TL Module No detail available for this fault.

1. DM-TL Module. See step 1 under CHECK.

1. DM-TL Module No detail available for this fault.

1. DM-TL Module. See step 1 under CHECK.

1. DM-TL Module No detail available for this fault.

1. Short circuit to battery C0331/30. See step 1 under CHECK.
2. Connectors C0331, DM-TL Connector. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. DM-TL module. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit to battery C0331/30. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, DM-TL Connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. DM-TL Module No detail available for this fault.

1. Short circuit to ground C0331/30. See step 1 under CHECK.
2. Connectors C0331, DM-TL Connector. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. DM-TL module. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit to ground C0331/30. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, DM-TL Connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. DM-TL Module No detail available for this fault.

1. Open circuit C0331/30 - DMTL valve output. See step 1 under CHECK.
2. Connectors C0331, DM-TL Connector. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. DMTL module. See step 4 under CHECK.

1. SHORT_CIRCUIT Open circuit C0331/30 - DM-TL valve output. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, DM-TL Connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. DM-TL Module No detail available for this fault.

1. Open circuit DM-TL heater output drive. See step 1 under CHECK.
2. Connectors C0331, DM-TL Connector. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. DM-TL module. See step 4 under CHECK.

1. SHORT_CIRCUIT Open circuit DM-TL heater output drive. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, DM-TL Connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. DM-TL Module No detail available for this fault.

1. Short circuit to ground DM-TL heater output drive. See step 1 under CHECK.
2. Connectors C0331, DM-TL Connector. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. DM-TL module. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit to ground DM-TL heater output drive. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, DM-TL Connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. DM-TL Module No detail available for this fault.

1. Short circuit to battery DM-TL heater output drive. See step 1 under CHECK.
2. Connectors C0331, DM-TL Connector. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. DM-TL module. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit to battery DM-TL heater output drive. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, DM-TL Connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. DM-TL Module No detail available for this fault.

1. Open circuit C0331/20 - DM-TL pump output. See step 1 under CHECK.
2. Connectors C0331, DM-TL Connector. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. DM-TL module. See step 4 under CHECK.

1. SHORT_CIRCUIT Open circuit C0331/20 - DM-TL pump output. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, DM-TL Connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. DM-TL Module No detail available for this fault.

1. Short circuit to ground C0331/20. See step 1 under CHECK.
2. Connectors C0331, DMTL Connector. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. DM-TL module. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit to ground C0331/20. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, DM-TL Connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. DM-TL Module No detail available for this fault.

1. Short circuit to battery C0331/20. See step 1 under CHECK.
2. Connectors C0331, DM-TL Connector. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. DM-TL module. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit to battery C0331/20. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0331, DM-TL Connector. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. DM-TL Module No detail available for this fault.

1. Connector C0331, C0862. See step 1 under CHECK.
2. ABS/Traction Control ECU. See step 2 under CHECK.
3. V8 Engine Management System ECM. See step 3 under CHECK.

1. CONNECTOR Connector C0331, C0862. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. ABS/Traction Control ECU No detail available for this fault.
3. V8 Engine Management System ECM No detail available for this fault.

1. Short circuit C0606/29 (GU) to ground. See step 1 under CHECK.
2. Connectors C0606, C2316. See step 2 under CHECK.
3. VANOS actuator bank 1. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/29 (GU) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C2316. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. VANOS Actuator Bank 1 No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Short circuit C0606/29 (GU) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C2316. See step 2 under CHECK.
3. VANOS actuator bank 1. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/29 (GU) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C2316. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. VANOS Actuator Bank 1 No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Short circuit C0606/29 (GU) - C2316/2 (GU). See step 1 under CHECK.
2. Connectors C0606, C2316. See step 2 under CHECK.
3. VANOS actuator bank 1. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/29 (GU) - C2316/2 (GU). Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C2316. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. VANOS Actuator Bank 1 No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Short circuit C0606/29 (GS) - C2317/2 (GS). See step 1 under CHECK.
2. Connectors C0606, C2317. See step 2 under CHECK.
3. VANOS actuator bank 2. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/29 (GS) - C2317/2 (GS). Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C2317. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. VANOS Actuator Bank 2 No detail available for this fault.
4. V8 Engine Management System ECM . No detail available for this fault.

1. Short circuit C0606/29 (GS) to ground. See step 1 under CHECK.
2. Connectors C0606, C2317. See step 2 under CHECK.
3. VANOS actuator bank 2. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/29 (GS) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C2317. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. VANOS Actuator Bank 2 No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Short circuit C0606/16 (GS) - battery. See step 1 under CHECK.
2. Connectors C0606, C2317. See step 2 under CHECK.
3. VANOS actuator bank 2. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/16 (GS) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C2317. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. VANOS Actuator Bank 2 No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Multifunction Steering Wheel (MFL) module. See step 1 under CHECK.

1. Multifunction Steering Wheel (MFL) Module Replace the Multifunction Steering Wheel (MFL) module.

1. Short circuit C0331/27 (YB) to battery voltage. See step 1 under CHECK.
2. Short circuit C0331/27 (YB) - 5V. See step 2 under CHECK.
3. Short circuit C0331/27 (YB) to ground. See step 3 under CHECK.
4. Short circuit C0082/8 (YB) to battery voltage. See step 4 under CHECK.
5. Short circuit C0082/8 (YB) - 5V. See step 5 under CHECK.
6. Short circuit C0082/8 (YB) to ground. See step 6 under CHECK.
7. Short circuit C2287/1 (R) to battery voltage. See step 7 under CHECK.
8. Short circuit C2287/1 (R) - 5V. See step 8 under CHECK.
9. Short circuit C2287/1 (R) to ground. See step 9 under CHECK.
10. Short circuit C2285/2 (R) to battery voltage. See step 10 under CHECK.
11. Short circuit C2285/2 (R) - 5V. See step 11 under CHECK.
12. Short circuit C2285/2 (R) to ground. See step 12 under CHECK.
13. Open circuit C0331/27 (YB) - C0082/8 (YB). See step 13 under CHECK.
14. Open circuit C2287/1 (R) - C2285/2 (R). See step 14 under CHECK.
15. Connectors C0331, C0082, C2287, C2285. See step 15 under CHECK.
16. Harness integrity. See step 16 under CHECK.
17. Multifunction Steering Wheel (MFL) module. See step 17 under CHECK.
18. V8 Engine Management System ECM. See step 18 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/27 (YB) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0331/27 (YB) - 5V. Check resistance < 5.0ohm.
3. SHORT_CIRCUIT Short circuit C0331/27 (YB) to ground. Check resistance < 5.0ohm.
4. SHORT_CIRCUIT Short circuit C0082/8 (YB) to battery voltage. Check resistance < 5.0ohm.
5. SHORT_CIRCUIT Short circuit C0082/8 (YB) - 5V. Check resistance < 5.0ohm.
6. SHORT_CIRCUIT Short circuit C0082/8 (YB) to ground. Check resistance < 5.0ohm.
7. SHORT_CIRCUIT Short circuit C2287/1 (R) to battery voltage. Check resistance < 5.0ohm.
8. SHORT_CIRCUIT Short circuit C2287/1 (R) - 5V. Check resistance < 5.0ohm.
9. SHORT_CIRCUIT Short circuit C2287/1 (R) to ground. Check resistance < 5.0ohm.
10. SHORT_CIRCUIT Short circuit C2285/2 (R) to battery voltage. Check resistance < 5.0ohm.
11. SHORT_CIRCUIT Short circuit C2285/2 (R) - 5V. Check resistance < 5.0ohm.
12. SHORT_CIRCUIT Short circuit C2285/2 (R) to ground. Check resistance < 5.0ohm.
13. OPEN_CIRCUIT Open circuit C0331/27 (YB) - C0082/8 (YB). Check resistance > 1Mohm.
14. OPEN_CIRCUIT Open circuit C2287/1 (R) - C2285/2 (R). Check resistance > 1Mohm.
15. CONNECTOR Connectors C0331, C0082, C2287, C2285. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
16. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
17. Multifunction Steering Wheel (MFL) Module Replace the Multifunction Steering Wheel (MFL) module.
18. V8 Engine Management System ECM No detail available for this fault.

1. Multifunction Steering Wheel (MFL) module. See step 1 under CHECK.

1. Multifunction Steering Wheel (MFL) Module Replace the Multifunction Steering Wheel (MFL) module.

1. Cruise control switch. See step 1 under CHECK.
2. Connectors C0331, C0082, C2287, C2285. See step 2 under CHECK.
3. Harness integrity. See step 3 under CHECK.
4. Multifunction Steering Wheel (MFL) module. See step 4 under CHECK.

1. Cruise Control Switch Check the following: Check the correct operation of the cruise control buttons. If the button operation is OK, and there are no harness/connector faults, replace the Multifunction Steering Wheel (MFL) module.
2. CONNECTOR Connectors C0331, C0082, C2287, C2285. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Multifunction Steering Wheel (MFL) Module Replace the Multifunction Steering Wheel (MFL) module.

1. Electronic Automatic Transmission ECU. See step 1 under CHECK.

1. Electronic Automatic Transmission ECU No detail available for this fault.

1. Electronic Automatic Transmission ECU. See step 1 under CHECK.

1. Electronic Automatic Transmission ECU No detail available for this fault.

1. Electronic Automatic Transmission ECU. See step 1 under CHECK.

1. Electronic Automatic Transmission ECU No detail available for this fault.

1. Engine Compartment Fusebox - Fuse 1. See step 1 under CHECK.
2. Short circuit C0606/31 (NW) to ground. See step 2 under CHECK.
3. Connectors C0606, C0422, C0570. See step 3 under CHECK.
4. Harness integrity. See step 4 under CHECK.
5. Thermostat heater element short circuit to ground. See step 5 under CHECK.
6. Engine coolant temperature sensor. See step 6 under CHECK.
7. Radiator outlet temperature sensor. See step 7 under CHECK.

1. POWER_DISTRIBUTION Engine Compartment Fusebox - Fuse 1. Check the following: Check for fuse not correctly inserted, fuse blown, fuse connections loose, damaged or corroded. Certain diagnostics may also perform further checks to try and narrow down the fault. For example, check if other circuits fed by the same fuse are also experiencing problems.
2. SHORT_CIRCUIT Short circuit C0606/31 (NW) to ground. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0606, C0422, C0570. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
5. Thermostat Heater Element Short Circuit To Ground No detail available for this fault.
6. Engine Coolant Temperature Sensor No detail available for this fault.
7. Radiator Outlet Temperature Sensor No detail available for this fault.

1. Open circuit C0606/31 (NW) - C0422/1 (NW). See step 1 under CHECK.
2. Connectors C0606, C0422. See step 2 under CHECK.
3. Electric Thermostat. See step 3 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/31 (NW) - C0422/1 (NW). Check resistance > 1Mohm.
2. CONNECTOR Connectors C0606, C0422. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. OPEN_CIRCUIT Electric Thermostat. Check resistance > 1Mohm.

1. Short circuit C0606/31 (NW) to ground. See step 1 under CHECK.
2. Connectors C0606, C0422. See step 2 under CHECK.
3. Electric Thermostat. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/31 (NW) to ground. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0422. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. SHORT_CIRCUIT Electric Thermostat. Check resistance < 5.0ohm.

1. Short circuit C0606/31 (NW) to battery voltage. See step 1 under CHECK.
2. Connectors C0606, C0422. See step 2 under CHECK.
3. Electric Thermostat. See step 3 under CHECK.

1. SHORT_CIRCUIT Short circuit C0606/31 (NW) to battery voltage. Check resistance < 5.0ohm.
2. CONNECTOR Connectors C0606, C0422. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. SHORT_CIRCUIT Electric Thermostat. Check resistance < 5.0ohm.

1. Driver error - crank while engine running. See step 1 under CHECK.
2. Short circuit C0331/6 (BY) to battery voltage. See step 2 under CHECK.
3. Connectors C0331, C0028. See step 3 under CHECK.
4. Starter relay. See step 4 under CHECK.
5. Ignition switch. See step 5 under CHECK.

1. Driver Error - Crank While Engine Running No detail available for this fault.
2. SHORT_CIRCUIT Short circuit C0331/6 (BY) to battery voltage. Check resistance < 5.0ohm.
3. CONNECTOR Connectors C0331, C0028. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. RELAY Starter relay. Check for relay not correctly seated, backed out pins, damaged pins, corroded pins, relay coil open circuit, faulty relay contacts, ensure power & ground feeds to relay coil are present and that the relay is energized.
5. Ignition Switch No detail available for this fault.

1. Short circuit C0331/21 (SN) to battery voltage. See step 1 under CHECK.
2. Short circuit C0331/21 (SN) - 5V. See step 2 under CHECK.
3. Short circuit C0331/21 (SN) to ground. See step 3 under CHECK.
4. Immobilization ECU. See step 4 under CHECK.
5. V8 Engine Management System ECM. See step 5 under CHECK.

1. SHORT_CIRCUIT Short circuit C0331/21 (SN) to battery voltage. Check resistance < 5.0ohm.
2. SHORT_CIRCUIT Short circuit C0331/21 (SN) - 5V. Check resistance < 5.0ohm.
3. SHORT_CIRCUIT Short circuit C0331/21 (SN) to ground. Check resistance < 5.0ohm.
4. Immobilization ECU No detail available for this fault.
5. V8 Engine Management System ECM No detail available for this fault.

1. V8 Engine Management System ECM. See step 1 under CHECK.

1. V8 Engine Management System ECM No detail available for this fault.

1. V8 Engine Management System ECM. See step 1 under CHECK.

1. V8 Engine Management System ECM No detail available for this fault.

1. Connectors C0331, C0862, C0787, C0175. See step 1 under CHECK.
2. ABS/traction control fault. See step 2 under CHECK.
3. Transfer box control fault. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. CONNECTOR Connectors C0331, C0862, C0787, C0175. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. ABS/Traction Control Fault No detail available for this fault.
3. Transfer Box Control Fault No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Connectors C0606, C0175. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Electronic throttle actuator. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C0175. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Electronic Throttle Actuator No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Open circuit C0606/42 (W) - C0175/4. See step 1 under CHECK.
2. Open circuit C0606/43 (R) - C0175/6. See step 2 under CHECK.
3. Short circuit C0606/42 (W) to ground. See step 3 under CHECK.
4. Short circuit C0606/43 (R) to ground. See step 4 under CHECK.
5. Short circuit C0606/42 (W) to battery voltage. See step 5 under CHECK.
6. Short circuit C0606/43 (R) to battery voltage. See step 6 under CHECK.
7. Connectors C0606, C0175. See step 7 under CHECK.
8. Harness integrity. See step 8 under CHECK.
9. Electronic Throttle actuator. See step 9 under CHECK.
10. V8 Engine Management System ECM. See step 10 under CHECK.

1. OPEN_CIRCUIT Open circuit C0606/42 (W) - C0175/4. Check resistance > 1Mohm.
2. OPEN_CIRCUIT Open circuit C0606/43 (R) - C0175/6. Check resistance > 1Mohm.
3. SHORT_CIRCUIT Short circuit C0606/42 (W) to ground. Check resistance < 5.0ohm.
4. SHORT_CIRCUIT Short circuit C0606/43 (R) to ground. Check resistance < 5.0ohm.
5. SHORT_CIRCUIT Short circuit C0606/42 (W) to battery voltage. Check resistance < 5.0ohm.
6. SHORT_CIRCUIT Short circuit C0606/43 (R) to battery voltage. Check resistance < 5.0ohm.
7. CONNECTOR Connectors C0606, C0175. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
8. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
9. Electronic Throttle Actuator No detail available for this fault.
10. V8 Engine Management System ECM No detail available for this fault.

1. Connectors C0606, C0175. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Electronic Throttle actuator. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C0175. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Electronic Throttle Actuator No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Connectors C0606, C0175. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Electronic Throttle actuator. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C0175. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Electronic Throttle Actuator No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Connectors C0606, C0175. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Electronic Throttle actuator. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C0175. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Electronic Throttle Actuator No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Connectors C0606, C0175. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Electronic Throttle actuator. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C0175. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Electronic Throttle Actuator No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Connectors C0606, C0175. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Electronic Throttle Actuator. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C0175. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Electronic Throttle Actuator No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Connectors C0606, C0175. See step 1 under CHECK.
2. Harness integrity. See step 2 under CHECK.
3. Electronic Throttle actuator. See step 3 under CHECK.
4. V8 Engine Management System ECM. See step 4 under CHECK.

1. CONNECTOR Connectors C0606, C0175. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Electronic Throttle Actuator No detail available for this fault.
4. V8 Engine Management System ECM No detail available for this fault.

1. Circuit integrity to C0331/36 (YB). See step 1 under CHECK.
2. Circuit integrity to C0331/37 (YN). See step 2 under CHECK.
3. Connector C0331. See step 3 under CHECK.
4. Electronic Automatic Transmission ECM. See step 4 under CHECK.
5. V8 Engine Management System ECM. See step 5 under CHECK.

1. CIRCUIT_INTEGRITY Circuit integrity to C0331/36 (YB). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CIRCUIT_INTEGRITY Circuit integrity to C0331/37 (YN). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CONNECTOR Connector C0331. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Electronic Automatic Transmission ECM No detail available for this fault.
5. V8 Engine Management System ECM No detail available for this fault.

1. Circuit integrity to C0331/36 (YB). See step 1 under CHECK.
2. Circuit integrity to C0331/37 (YN). See step 2 under CHECK.
3. Connector C0331. See step 3 under CHECK.
4. Instrument Pack. See step 4 under CHECK.
5. V8 Engine Management System ECM. See step 5 under CHECK.

1. CIRCUIT_INTEGRITY Circuit integrity to C0331/36 (YB). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CIRCUIT_INTEGRITY Circuit integrity to C0331/37 (YN). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CONNECTOR Connector C0331. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Instrument Pack No detail available for this fault.
5. V8 Engine Management System ECM No detail available for this fault.

1. Open circuit C0331/36 (YB) - C0862/3 (YB). See step 1 under CHECK.
2. Open circuit C0331/37 (YN) - C0862/4 (YN). See step 2 under CHECK.
3. Connectors C0331, C0862. See step 3 under CHECK.
4. ABS/Traction Control ECU. See step 4 under CHECK.
5. V8 Engine Management System ECM. See step 5 under CHECK.

1. OPEN_CIRCUIT Open circuit C0331/36 (YB) - C0862/3 (YB). Check resistance > 1Mohm.
2. OPEN_CIRCUIT Open circuit C0331/37 (YN) - C0862/4 (YN). Check resistance > 1Mohm.
3. CONNECTOR Connectors C0331, C0862. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. ABS/Traction Control ECU No detail available for this fault.
5. V8 Engine Management System ECM No detail available for this fault.

1. Circuit integrity to C0331/36 (YB). See step 1 under CHECK.
2. Circuit integrity to C0331/37 (YN). See step 2 under CHECK.
3. Connector C0331. See step 3 under CHECK.
4. Transfer box control module. See step 4 under CHECK.
5. V8 Engine Management System ECM. See step 5 under CHECK.

1. CIRCUIT_INTEGRITY Circuit integrity to C0331/36 (YB). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CIRCUIT_INTEGRITY Circuit integrity to C0331/37 (YN). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CONNECTOR Connector C0331. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
4. Transfer Box Control Module No detail available for this fault.
5. V8 Engine Management System ECM No detail available for this fault.

1. Other V8 Engine Management System ECM faults. See step 1 under CHECK.
2. V8 Engine Management System ECM. See step 2 under CHECK.

1. Other V8 Engine Management System ECM Faults Check the following: It is possible that an internal V8 Engine Management System ECM fault has occurred. Diagnose and clear all other faults raised by the V8 Engine Management System ECM. Only if this fault persists should you renew the ECM.
2. V8 Engine Management System ECM No detail available for this fault.

1. Other V8 Engine Management System ECM faults. See step 1 under CHECK.
2. V8 Engine Management System ECM. See step 2 under CHECK.

1. Other V8 Engine Management System ECM Faults Check the following: It is possible that an internal V8 Engine Management System ECM fault has occurred. Diagnose and clear all other faults raised by the V8 Engine Management System ECM. Only if this fault persists should you renew the ECM.
2. V8 Engine Management System ECM No detail available for this fault.

1. Harness integrity. See step 1 under CHECK.
2. Connectors C0331, C0059. See step 2 under CHECK.
3. Immobilization ECU. See step 3 under CHECK.

1. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CONNECTOR Connectors C0331, C0059. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Immobilization ECU No detail available for this fault.

1. The V8 Engine Management System ECM has been exchanged for one from another vehicle. See step 1 under CHECK.
2. The Immobilization ECU has been exchanged for one from another vehicle. See step 2 under CHECK.

1. The V8 Engine Management System ECM Has Been Exchanged For One From Another Vehicle No detail available for this fault.
2. The Immobilization ECU Has Been Exchanged For One From Another Vehicle No detail available for this fault.

1. Learn immobilization code. See step 1 under CHECK.

1. Learn Immobilization Code No detail available for this fault.

1. Harness integrity. See step 1 under CHECK.
2. Connectors C0331, C0059. See step 2 under CHECK.
3. Immobilization ECU. See step 3 under CHECK.

1. CIRCUIT_INTEGRITY Harness integrity. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
2. CONNECTOR Connectors C0331, C0059. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. Immobilization ECU No detail available for this fault.

1. V8 Engine Management System ECM. See step 1 under CHECK.

1. V8 Engine Management System ECM No detail available for this fault.

1. Attempt to tamper with immobilization. See step 1 under CHECK.

1. Attempt To Tamper With Immobilization No detail available for this fault.

1. CAN Bus. See step 1 under CHECK.

1. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. Connector C0331, C0862. See step 1 under CHECK.
2. Transfer Box ECU. See step 2 under CHECK.

1. CONNECTOR Connector C0331, C0862. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. Transfer Box ECU There is a transfer box signal fault. Check the transfer box system for faults. Use Real Time Monitoring to monitor the transfer box range change signal. This fault is raised if the selected transfer box range (low or high) is selected and is different from the current range for more than one minute.

1. Connector C0331, C0862. See step 1 under CHECK.
2. Transfer box control system. See step 2 under CHECK.

1. CONNECTOR Connector C0331, C0862. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. Transfer Box Control System There is a transfer box signal fault. Check the transfer box system for faults. Use Real Time Monitoring to monitor the transfer box range change signal. This fault is raised if the selected transfer box range (low or high) is selected and is different from the current range for more than one minute.

1. DTC P1710 Battery Feed KI87 Fault: General Fault
2. DTC P1710 Battery Feed KI87 Fault: Plausibility Fault

1. Engine fusebox Fuse 1. See step 1 under CHECK.
2. Connectors C0932, C0570. See step 2 under CHECK.
3. Circuit integrity C0932/8 (RU) - C0570/2 (RU). See step 3 under CHECK.
4. Circuit integrity C0932/9 (RU) - C0570/2 (RU). See step 4 under CHECK.
5. Circuit integrity C0932/4 (N) to ground (N). See step 5 under CHECK.
6. Circuit integrity C0932/5 (N) to ground (N). See step 6 under CHECK.
7. Circuit integrity C0932/6 (N) to ground (N). See step 7 under CHECK.
8. Electronic Automatic Transmission ECU. See step 8 under CHECK.

1. POWER_DISTRIBUTION Engine Fusebox Fuse 1. Check the following: Check for fuse not correctly inserted, fuse blown, fuse connections loose, damaged or corroded. Certain diagnostics may also perform further checks to try and narrow down the fault. Check if other circuits fed by the same fuse are also experiencing problems.
2. CONNECTOR Connectors C0932, C0570. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Circuit integrity C0932/8 (RU) - C0570/2 (RU). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. CIRCUIT_INTEGRITY Circuit integrity C0932/9 (RU) - C0570/2 (RU). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
5. CIRCUIT_INTEGRITY Circuit integrity C0932/4 (N) to ground (N). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
6. CIRCUIT_INTEGRITY Circuit integrity C0932/5 (N) to ground (N). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
7. CIRCUIT_INTEGRITY Circuit integrity C0932/6 (N) to ground (N). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
8. Electronic Automatic Transmission ECU No detail available for this fault.

1. Engine fusebox Fuse 4. See step 1 under CHECK.
2. Connectors C0932, C0570. See step 2 under CHECK.
3. Circuit integrity C0932/7 (R) - C0570/8 (R). See step 3 under CHECK.
4. Electronic Automatic Transmission ECU. See step 4 under CHECK.

1. POWER_DISTRIBUTION Engine fusebox Fuse 4: Check for fuse not correctly inserted, fuse blown, fuse connections loose, damaged or corroded. Certain diagnostics may also perform further checks to try and narrow down the fault. For example, check if other circuits fed by the same fuse are also experiencing problems.
2. CONNECTOR Connectors C0932, C0570. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
3. CIRCUIT_INTEGRITY Circuit integrity C0932/7 (R) - C0570/8 (R). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P1743 Pressure Line Solenoid 5 Fault: General Fault
2. DTC P1743 Pressure Line Solenoid 5 Fault: Short Circuit To Battery
3. DTC P1743 Pressure Line Solenoid 5 Fault: Short Circuit To Ground Or Open Circuit
4. DTC P1745 Pressure Line Solenoid 5 Fault: Plausibility Fault

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/11 (P) - C0244/12 (P). See step 2 under CHECK.
3. Circuit integrity C1835/6 (YR) - C0244/15 (YR). See step 3 under CHECK.
4. Gearbox Pressure Line Solenoid (EDS) 5. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/11 (P) - C0244/12 (P). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C1835/6 (YR) - C0244/15 (YR). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Gearbox Pressure Line Solenoid (EDS) 5 No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. Connectors C1835, C0244. See step 1 under CHECK.
2. Circuit integrity C1835/11 (P) - C0244/12 (P). See step 2 under CHECK.
3. Gearbox pressure line solenoids. See step 3 under CHECK.
4. Electronic Automatic Transmission ECU. See step 4 under CHECK.

1. CONNECTOR Connectors C1835, C0244. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C1835/11 (P) - C0244/12 (P). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. Gearbox Pressure Line Solenoids No detail available for this fault.
4. Electronic Automatic Transmission ECU No detail available for this fault.

1. Connectors C0193, C0685, C1664. See step 1 under CHECK.
2. Circuit integrity C0193/20 (UY) - C1664/2 (UY). See step 2 under CHECK.
3. Circuit integrity C0193/19 (US) - C1664/3 (US). See step 3 under CHECK.
4. Circuit integrity C0193/18 (WU) - C0685/3 (WU). See step 4 under CHECK.
5. Circuit integrity C0685/1 (WG) - C1664/4 (WG). See step 5 under CHECK.
6. Circuit integrity C1664/1 (NB) to ground. See step 6 under CHECK.
7. Steptronic Switch. See step 7 under CHECK.
8. Transmission High/Low Switch. See step 8 under CHECK.
9. Electronic Automatic Transmission ECU. See step 9 under CHECK.

1. CONNECTOR Connectors C0193, C0685, C1664. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C0193/20 (UY) - C1664/2 (UY). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C0193/19 (US) - C1664/3 (US). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. CIRCUIT_INTEGRITY Circuit integrity C0193/18 (WU) - C0685/3 (WU). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
5. CIRCUIT_INTEGRITY Circuit integrity C0685/1 (WG) - C1664/4 (WG). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
6. CIRCUIT_INTEGRITY Circuit integrity C1664/1 (NB) to ground. Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
7. Steptronic Switch Check for open/short circuit with switch open/closed.
8. Transmission High/Low Switch Check for open/short circuit with switch open/closed.
9. Electronic Automatic Transmission ECU No detail available for this fault.

1. DTC P1825 Shift Solenoid Shift Lock Fault: Open Circuit
2. DTC P1825 Shift Solenoid Shift Lock Fault: Plausibility Fault
3. DTC P1825 Shift Solenoid Shift Lock Fault: Short Circuit To Battery
4. DTC P1825 Shift Solenoid Shift Lock Fault: Short Circuit To Ground

1. Connectors C0193, C0673. See step 1 under CHECK.
2. Circuit integrity C0193/2 (BP) - C0673/1 (BP). See step 2 under CHECK.
3. Circuit integrity C0193/1 (NP) - C0673/3 (NP). See step 3 under CHECK.
4. Shift Interlock Solenoid. See step 4 under CHECK.
5. Electronic Automatic Transmission ECU. See step 5 under CHECK.

1. CONNECTOR Connectors C0193, C0673. Check for connector not correctly latched, backed out pins, damaged pins, corroded pins.
2. CIRCUIT_INTEGRITY Circuit integrity C0193/2 (BP) - C0673/1 (BP). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
3. CIRCUIT_INTEGRITY Circuit integrity C0193/1 (NP) - C0673/3 (NP). Check for open circuit, short circuit to ground, supply or other circuit, damaged or unlatched connector, intermediate connectors or headers.
4. Shift Interlock Solenoid No detail available for this fault.
5. Electronic Automatic Transmission ECU No detail available for this fault.

1. CAN Bus. See step 1 under CHECK.

1. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. CAN Bus. See step 1 under CHECK.

1. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. CAN Bus. See step 1 under CHECK.

1. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. CAN Bus. See step 1 under CHECK.

1. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. CAN Bus. See step 1 under CHECK.

1. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. CAN Bus. See step 1 under CHECK.

1. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

1. CAN Bus. See step 1 under CHECK.

1. CAN Bus Fault Check the following: Integrity of all CAN Bus connections. Look for similar faults in other ECUs on the CAN Bus. Look for faults in the originating ECU (if applicable), including intermittent supplies/ground faults. Refer to the CAN Bus wiring diagram. For 2003 MY, see «COMPUTER DATA LINES»(ref-159346-S39125510552003120100000) in SYSTEM WIRING DIAGRAMS article. For 2004 MY, see «COMPUTER DATA LINES»(ref-166687-S04716762612004092700000) in SYSTEM WIRING DIAGRAMS article.

WIRE COLORS

For wire color codes used in diagnostic tests, see WIRE COLOR CODES table.

WIRE COLOR CODES

See also:
• DTC P0010