HYDRAULIC LASH ADJUSTER PRIMING Land Rover Freelander L359

HYDRAULIC LASH ADJUSTER PRIMING

Note. Hydraulic lash adjusters are fitted to the intake camshaft only.

1. Check the engine oil level.
2. If lash adjuster noise occurs when the engine is started, allow the engine to warm at idle for 1 minute (at -20 degrees celsius allow the engine to warm for 5 minutes).
3. Run the engine at 3500 RPM for 1 minute.
4. Allow the engine to idle for 30 seconds.
5. If the valve train noise is still present, repeat the above up to a maximum of 6 times.

Scheme 189

Scheme 190

Scheme 191

Scheme 192

Scheme 193

Scheme 194

Scheme 195

Scheme 196

Scheme 197

Scheme 198

Scheme 199

Scheme 200

Scheme 201

Scheme 202

Scheme 203

Scheme 204

1. Disconnect the battery ground cable. Refer to «Specifications»(ref-531959-S27829531522013022000000) .
2. Remove the engine cover. Refer to «Engine Cover - 3.2L»(ref-531951-S06303498242013022000000) .
3. Remove the air cleaner assembly. Refer to «Air Cleaner»(ref-531922-S17101109672013022000000) .
4. Raise and support the vehicle.
5. Remove the engine undershield. Refer to «Engine Undershield»(ref-531949-S17696129762013022000000) .
6. See figure.
7. See figure.
8. Remove the air cleaner outlet pipe.
9. Remove the 2 lower intake manifold bolts.
10. Disconnect the MAP sensor electrical connector.
11. Disconnect the throttle body electrical connector.
12. Disconnect the fuel purge line.
13. Disconnect the purge control valve (PCV) electrical connector.
14. Disconnect the fuel rail pressure (FRP) sensor electrical connector.
15. Remove the dipstick.
16. Disconnect the coolant bleed hose.
17. Release the PAS fluid reservoir from the bracket and tie aside.
18. Remove the A/C line support bracket.
19. Remove the cooling fan module.
20. Remove the intake manifold.
21. Disconnect the 2 intake manifold module connectors.
22. Remove the throttle body.
23. Remove the 2 intake manifold modules.
24. Remove the purge valve assembly.
25. Remove the manifold absolute pressure (MAP) sensor.
26. Remove and discard the intake manifold gaskets.

Scheme 205

1. Clean the component mating faces.
2. Install the gaskets.
3. Install the intake manifold modules.
4. Install the MAP sensor.
5. Install the purge valve assembly.
6. Install the throttle body and tighten the screws in the sequence shown. Torque: 8
7. Install the inlet manifold and tighten the bolts. Torque: 16
8. Install the cooling fan module.
9. Connect the coolant bleed hose.
10. Install the PAS fluid reservoir in the bracket.
11. Install the dipstick.
12. Connect and secure the electrical connectors.
13. Install the A/C line support bracket and tighten the bolt. Torque: 10
14. Connect the purge line.
15. Install the lower intake manifold bolts. Torque: 10
16. Install the air cleaner outlet pipe.
17. Install the engine undershield. Refer to «Engine Undershield»(ref-531949-S17696129762013022000000) .
18. Install the front undershield.
19. Install the front towing eye cover.
20. Install the air cleaner assembly. Refer to «Air Cleaner»(ref-531922-S17101109672013022000000) .
21. Install the engine cover. Refer to «Engine Cover - 3.2L»(ref-531951-S06303498242013022000000) .
22. Connect the battery ground cable. Refer to «Specifications»(ref-531959-S27829531522013022000000) .
23. Check and top-up the coolant.