Home ReviewsRefund
Home/Kia/Optima/Kia Optima II (2005-2008)/Repair manual/Fuses & Circuit Breakers/Fuses & Relays: Other
Contents Wiring diagrams Section: Fuses & Circuit Breakers All sections

Fuses & Relays: Other Kia Optima II

Fuses & Circuit Breakers ~617 words

FUSIBLE LINKS & FUSES INFORMATION

For fuse locations within the engine compartment fuse box (Схема №3)

Note. Use designated fuses only.

DESCRIPTIONAMPERAGECIRCUIT PROTECTED
FUSIBLE LINKSALT.125A (2.0L/2.4L) 150A (2.7L/Diesel)Alternator
I/P B+. 250AI/P Junction Box (Hot At All Times)
ABS-240AABS/ESP Control Module
ABS-140AABS/ESP Control Module, Multipurpose Check Connector
BLOWER40ABlower Relay
RR HTD40ARear Defogger Relay
IGN-130AIgnition Switch (ACC, IG1)
RAD30A (2.0L/2.4L) 40A (2.7L/Diesel)Radiator Fan Relay
ECU RLY30AEngine Control Relay, PCM
IGN-230AIgnition Switch (IG2, START), Start Relay
I/P B+. 130AI/P Junction Box (Hot At All Times)
FUSESS/WARMER25ASeat Warmer Relay
ACC SOCKET25APower Outlet
ATM20AATM Control Relay
S/ROOF20ASunroof Control Module
P/AMP20AAudio AMP
F/PUMP20AFuel Pump Relay
IGN COIL20AIgnition Coil (Gasoline)
ECU-120APCM (2.0L/2.4L/Diesel)
TAIL20ATail Lamp Relay
FRT FOG15AFront Fog Lamp Relay
DRL15ADRL Control Module
HORN15AHorn Relay, Burglar Alarm relay
H/LP LOW15AHead Lamp Relay (Low)
H/LP HI15AHead Lamp Relay (High)
SNSR-115AImmobilizer Control Module, Camshaft Position Sensor, MAF Sensor, Oil Control Valve, Canister Purge Solenoid Valve
SNSR-215AFuel Pump Relay, Oxygen Sensor, EGR Actuator
SNSR-310AA/C Relay, Injector, Lambda Sensor, VGT Actuator
ECU10ATCM, Alternator, PCM
PCU10APulse Generator, TCM, Radiator Fan Relay
ABS10AABS/ESP Control Module, Multipurpose Check Connector
BACK-UP10ABack-up Lamp Switch, Stop Lamp Switch, Vehicle Speed Sensor
A/CON10AA/C Relay

IDENTIFYING FUSIBLE LINKS & FUSES (ENGINE COMPARTMENT)

Fuse & Relay Index Information

For fuse locations within the passenger compartment fuse/relay box (Схема №12)

Use designated fuses only.

DescriptionFuse RatingProtected Components
H/LP10AHead Lamp Relay, AQS Sensor, HLLD, PTC Heater Relay, Fuel Filter Heater Relay
A/CON SW10AA/C Control Module, Blower Motor
START10AStarter Motor
P/SEAT RH30APower Seat (Right)
P/WDW RH25APower Window (Right)
WIPER25AFront Wiper, Wiper Relay
MIRR HTD10AOutside Rearview Mirror Defroster
RR FOG15ARear Fog Light
P/SEAT LH30APower Seat (Left)
P/WDW LH25APower Window (Left)
SPARE10ASpare Fuse
MODULE-210ACluster, Rain Sensor, Sunroof, BCM, Rheostat, Seat Warmer Electronic Chrome Mirror
W/DEICER15ADeicer
TAIL RH10AHead Lamp RH, Rear Combination Lamps RH, License Plate Lamp RH
TAIL LH10AHead Lamp LH, Rear Combination Lamps LH, License Plate Lamp LH
EPS10APower Steering Wheel
A/CON10AAir Conditioner
SAFETY PWR20ASafety Power Window
A/BAG ND10AAirbag warning
A/BAG15AAir bag
DR LOOK25ACentral Door Lock
SPARE10ASpare Fuse
CLUSTER10ACluster
MODULE-110AATM Key Lock Control Module, Multifunction Switch, BWS Buzzer, ESP Switch
HAZARD15AHazard Warning Light
STOP LP15AStop Light
SPARE10ASpare Fuse
TELLTALE10AClock
T/LID OPEN15ATrunk Lid Opener
ADJ PEDAL10AAdjustable Pedal Relay, Sport Mode Switch
SPARE10ASpare Fuse
T/SIG10ATurn Signal Light
TPMS10ATire Pressure Monitoring System
BLOWER MTR10ABlower, Air conditioner
MEMORY *15ACluster, ETACS, NO, Clock, Room lamp
AUDIO *15AAudio
C/LIGHTER25ACigarette Lighter
D/CLOCK10ADigital Clock
*: Power connector consist of the Audio and Memory fuses.

IDENTIFYING FUSES (PASSENGER COMPARTMENT FUSE BOX)

Memory Fuse

This vehicle is equipped with a memory fuse to prevent battery discharge if the vehicle is parked without being operated for prolonged periods. Use the following procedures before parking the vehicle for prolonged period.

  1. Turn off the engine.
  2. Turn off the headlights and tail lights.
  3. Open the passenger room fuse box cover and pull up the MEMORY 15A / AUDIO 15A combined fuse holder. (Схема №12)

Note. If the memory fuse is pulled up from the fuse panel, the warning chime, audio, clock and interior lamps, etc., will not operate. Some items must be reset after fuse replacement. Even though the memory fuse is pulled up, the battery can still be discharged by operation of the headlights or other electrical devices.

HAZARD LAMP RELAY

Check for continuity between the terminals.

  1. There should be continuity between the No. 14 and No.15 terminals when power and ground are connected to the No.5 and No.15 terminals in the ICM relay B connector.
  2. There should be no continuity between the No14 and No.15 terminals when power is disconnected.

BURGLAR ALARM HORN

Check for continuity between the terminals.

  1. There should be continuity between the No. 11 and No. 12 terminals when power and ground are connected to the No.4 and No.11 terminals in the ICM relay B connector.
  2. There should be no continuity between the No.11 and No. 12 terminals when power is disconnected.

BURGLAR ALARM

Check for continuity between the terminals.

  1. There should be no continuity between the No.9 and No. 10 terminals when power and ground are connected to the No.1 and No.9 terminals in the ICM relay B connector.
  2. There should be continuity between the No.9 and No. 10 terminals when power is disconnected.

RAIN SENSOR

Check for continuity between the terminals.

  1. There should be continuity between the No.9 and No.10 terminals when power and ground are connected to the No.1 and No.4 terminals in the ICM relay A connector.
  2. There should be continuity between the No.9 and No.10 terminals when power is disconnected.

ADJUSTABLE PEDAL

Check for continuity between the terminals.

  1. There should be continuity between the No.5 and No. 12 terminals when power and ground are connected to the No.6 and No. 12 terminals in the ICM relay A connector.
  2. There should be no continuity between the No.5 and No. 12 terminals when power and ground are disconnected.

SEAT WARMER

Check for continuity between the terminals.

  1. There should be continuity between the No.7 and No. 17 terminals when power and ground are connected to the No. 14 and No. 15 terminals in the ICM relay A connector.
  2. There should be no continuity between the No.7 and No.17 terminals when power and ground are disconnected.

WIPER DEICER RELAY

Check for continuity between the terminals.

  1. There should be continuity between the No.8 and No. 18 terminals when power and ground are connected to the No.8 and No.9 terminals in the ICM relay A connector.
  2. There should be no continuity between the No.8 and No. 18 terminals when power and ground are disconnected.

REAR FOG RELAY

Check for continuity between the terminals.

  1. There should be continuity between the No.2 and No. 18 terminals when power and ground are connected to the No.17 and No. 18 terminals in the ICM relay A connector.
  2. There should be no continuity between the No.2 and No. 18 terminals when power and ground are disconnected.

More articles — Fuses & Relays