Additional Wiring
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
The engine coolant temperature sensor is a negative temperature coefficient thermistor-type sensor whose resistance varies inversely with temperature. At cold temperatures the sensor resistance is high so the voltage is high. As the coolant temperature increases the resistance decreases and the voltage becomes low. The INSUFFICIENT COOLANT TEMP FOR CLOSED-LOOP FUEL CONTROL determines if the engine coolant temperature will reach the closed loop fueling control temperature limit in a regulated time after start.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
The PCM predicts what the engine coolant temperature should be, based on the engine coolant temperature at start-up, ambient temperature and how the vehicle is subsequently driven. The predicted engine coolant temperature is compared to the Engine Coolant Temperature Sensor reading. The error between the two is calculated and integrated with respect to time. When the Thermostat diagnostic runs, the integrated error is compared to a calibrated threshold and pass/fail is determined. Separate pass and fail thresholds are used in order to improve accuracy of the diagnostic.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For an aged O2 sensor, the response rate to the air/fuel change is slower than when it was new. The O2 sensor tends to move less with the same air/fuel changes in a given time frame. Therefore by observing the activity of voltage readings from the upstream O2 sensor, the quality of the O2 sensor can be detected.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
This diagnostic provides a continuous check of the O2 heater circuit during operation. The heater circuit is momentarily disabled to allow a resistance measurement to be taken to infer heater temperature. The current delivery to the heater is duty cycled to maintain a specific target temperature. The error from the target temperature is continuously monitored to assess heater performance.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
The downstream O2 Sensor is located in the exhaust path behind the catalytic converter, is monitored for proper response to assure optimum catalytic converter efficiency. The downstream O2 response monitor is intended to diagnose a downstream O2 sensor that is not moving or stuck in a voltage window and to insure accurate information for catalyst monitor diagnosis.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
The downstream O2 Sensor is located in the exhaust path behind the catalytic converter, is monitored for proper response to assure optimum catalytic converter efficiency. The downstream O2 response monitor is intended to diagnose a downstream O2 sensor that is not moving or stuck in a voltage window and to insure accurate information for catalyst monitor diagnosis.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
The downstream O2 Sensor is located in the exhaust path behind the catalytic converter, is monitored for proper response to assure optimum catalytic converter efficiency. The downstream O2 response monitor is intended to diagnose a downstream O2 sensor that is not moving or stuck in a voltage window and to insure accurate information for catalyst monitor diagnosis.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
This diagnostic provides a continuous check of the O2 heater circuit during operation. The heater circuit is momentarily disabled to allow a resistance measurement to be taken to infer heater temperature. The current delivery to the heater is duty cycled to maintain a specific target temperature. The error from the target temperature is continuously monitored to assess heater performance.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For an aged O2 sensor, the response rate to the air/fuel change is slower than when it was new. The O2 sensor tends to move less with the same air/fuel changes in a given time frame. Therefore by observing the activity of voltage readings from the upstream O2 sensor, the quality of the O2 sensor can be detected.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
This diagnostic provides a continuous check of the O2 heater circuit during operation. The heater circuit is momentarily disabled to allow a resistance measurement to be taken to infer heater temperature. The current delivery to the heater is duty cycled to maintain a specific target temperature. The error from the target temperature is continuously monitored to assess heater performance.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
The downstream O2 Sensor is located in the exhaust path behind the catalytic converter, is monitored for proper response to assure optimum catalytic converter efficiency. The downstream O2 response monitor is intended to diagnose a downstream O2 sensor that is not moving or stuck in a voltage window and to insure accurate information for catalyst monitor diagnosis.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
This diagnostic provides a continuous check of the O2 heater circuit during operation. The heater circuit is momentarily disabled to allow a resistance measurement to be taken to infer heater temperature. The current delivery to the heater is duty cycled to maintain a specific target temperature. The error from the target temperature is continuously monitored to assess heater performance.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
The fuel feedback system will maintain a stoichiometric fuel/air mixture, 14.7:1, by modifying the injector pulse width according to the oxygen content of the exhaust gas. The PCM makes short term and long term fuel corrections to maintain stoichiometric fuel/air ratio for best catalytic converter efficiency. Short term fuel correction is based on upstream O2 sensor output and is designed for quick engine response. The long term fuel correction compensated for variations in the engine specifications, sensor tolerances and component aging and is designed to correct rich and lean conditions over a longer period of time.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
The fuel feedback system will maintain a stoiciometric fuel/air mixture, 14.7:1, by modifying the injector pulse width according to the oxygen content of the exhaust gas. The PCM makes short term and long term fuel corrections to maintain stoiciometric fuel/air ratio for best catalytic converter efficiency. Short term fuel correction is based on upstream O2 sensor output and is designed for quick engine response. The long term fuel correction compensated for variations in the engine specifications, sensor tolerances and component aging and is designed to correct rich and lean conditions over a longer period of time.
For complete wiring diagrams, refer to SYSTEM WIRING DIAGRAMS article.
The fuel feedback system will maintain a stoichiometric fuel/air mixture, 14.7:1, by modifying the injector pulse width according to the oxygen content of the exhaust gas. The PCM makes short term and long term fuel corrections to maintain stoichiometric fuel/air ratio for best catalytic converter efficiency. Short term fuel correction is based on upstream O2 sensor output and is designed for quick engine response. The long term fuel correction compensated for variations in the engine specifications, sensor tolerances and component aging and is designed to correct rich and lean conditions over a longer period of time.