Repair manual
Wiring diagrams
Infiniti M37 IV Repair Manual
Step-by-step repair and maintenance instructions for the Infiniti M37 IV (2010–2014): removal, installation, adjustment, diagnostics and parameter checks with illustrations.
73sections
658articles
ENManual language
- High Strength Steel (HSS)
- PROHIBITION OF CUT AND CONNECTION
- Foam Repair
- Undercoating
- Precautions in Undercoating
- Body Sealing
- Rear Fender Hemming Process
- Hoodledge
- Front Side Member (2WD)
- Front Side Member (AWD)
- Front Pillar
- Side Body
- Center Pillar
- Outer Sill
- Outer Rear Wheelhouse
- SUPPLEMENTARY WORK
- Rear Floor Rear
- Rear Side Member Extension
- Body Center Marks
- MEASUREMENT
- Precautions for Plastics
- Lan System (CAN Fundamental) 4
- Body Control System 6
- Lan System (CAN) 5
- Lan System (CAN Gateway) 6
- Lan System (CAN) (Type 1)
- Lan System (CAN) (Type 2)
- Lan System (CAN) (Type 3)
- Lan System (CAN) (Type 4)
- Lan System (CAN) (Type 5)
- Lan System (CAN) (Type 6)
- Lan System (CAN) (Type 7)
- Lan System (CAN) (Type 8)
- Lan System (CAN) (Type 9)
- Lan System (CAN) (Type 10)
- Lan System (CAN) (Type 11)
- Lan System (CAN) (Type 12)
- Engine Performance Diagnostic Routine Outline - General Information
- Engine Performance Safety Precautions
- Parasitic Load Explanation & Test Procedures - General Information 2
- Waveforms - Injector Pattern Tutorial - General Information 2
- Electrostatic Discharge Warning - General Information
- State Emission Standards - Diesel
- Special Service Tools
- Commercial Service Tools
- OIL LEAKAGE
- Bearing
- Side Gear and Pinion Mate Gear
- Side Gear Thrust Washer and Pinion Mate Thrust Washer
- Oil Seal
- Differential Case
- Companion Flange
- SIDE BEARING PRELOAD
- TOOTH CONTACT
- BACKLASH
- Drive Gear and Drive Pinion
- PINION GEAR HEIGHT
- PINION BEARING PRELOAD
- Drive Gear Runout
- Differential Side Gear Clearance
- Companion Flange Runout
- Terms
- Units
- Contents
- Components
- Connector Symbols
- SWITCH POSITIONS
- MULTIPLE SWITCH
- CONNECTOR LIST
- PREVIOUS STANDARD
- NEW STANDARD BASED ON ISO
- Recommended Chemical Products and Sealants
- Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
- PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
- Precautions For Xenon Headlamp Service
- Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
- Precaution for Procedure without Cowl Top Cover
- Cautions in Removing Battery Terminal and AV Control Unit (Models with AV Control Unit)
- Three Way Catalyst
- Engine Oils
- HEALTH PROTECTION PRECAUTIONS
- ENVIRONMENTAL PROTECTION PRECAUTIONS
- Air Conditioning
- Fuel
- Commercial Service Tools
- Garage Jack and Safety Stand and 2-Pole Lift
- Board-On Lift
- Tow Truck Towing
- FRONT
- REAR
- AUTOMATIC TRANSMISSION
- Model Variation
- Dimensions
- Wheels & Tires
- CONNECTOR AND TERMINAL PIN KIT
- HOW TO PROBE CONNECTORS
- Probing from Terminal Side
- How to Check Enlarged Contact Spring of Terminal
- Hint
- Sensor & Relay
- Engine Compartment
- Behind the Instrument Panel
- Under Seating Areas
- WATER INTRUSION
- ELECTRICAL LOAD
- COLD OR HOT START UP
- Continuity Check Method
- Voltage Check Method
- Resistance Check Method
- VOLTAGE DROP TESTS
- Measuring Voltage Drop - Accumulated Method
- FUNCTION
- ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL: Required Procedure After Battery Disconnection
- Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
- PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
- Precaution for Procedure without Cowl Top Cover
- Special Service Tools
- Circuit Breaker
- Battery
- NORMAL OPEN, NORMAL CLOSED AND MIXED TYPE RELAYS
- CONNECTOR SYMBOL
- How to Handle Battery
- METHODS OF PREVENTING OVER-DISCHARGE
- Check Electrolyte Level
- Specific Gravity Check
- Charging The Battery
- EXTENDED STORAGE SWITCH (IF EQUIPPED)
- How To Check