Home ReviewsRefund
Home/Infiniti/G37/Infiniti G37 IV рестайлинг (2006-2013)/Repair manual/Automatic Drive Positioner -- G37 Coupe/Component Function Check
Contents Section: Automatic Drive Positioner -- G37 Coupe All sections

Component Function Check Infiniti G37 IV рестайлинг

Automatic Drive Positioner -- G37 Coupe ~743 words

Component Function Check

  1. CHECK FUNCTION Turn ignition switch ON. Select "SLIDE SW-FR", "SLIDE SW-RR" in the "Data monitor" mode using CONSULT-III. Check sliding switch signal under the following conditions. MONITOR ITEM CONDITION CHART Monitor item Condition Status SLIDE SW-FR Sliding switch (forward) Operate ON Release OFF SLIDE SW-RR Sliding switch (backward) Operate ON Release OFF Is the indication normal? YES: INSPECTION END NO: Perform diagnosis procedure. Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S21913188212010022700000) ".
  1. CHECK FUNCTION Turn ignition switch ON. Select "RECLN SW-FR", "RECLN SW-RR" in the "Data monitor" mode using CONSULT-III. Check reclining switch signal under the following conditions. MONITOR ITEM CONDITION CHART Monitor item Condition Status RECLINE SW-FR Reclining switch (forward) Operate ON Release OFF RECLINE SW-RR Reclining switch (backward) Operate ON Release OFF Is the indication normal? YES: INSPECTION END NO: Perform diagnosis procedure. Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S10388105462010022700000) ".
  1. CHECK FUNCTION Turn ignition switch ON. Select "LIFT FR SW-UP", "LIFT FR SW-DN" in the "Data monitor" mode using CONSULT-III. Check lifting switch (front) signal under the following conditions. MONITOR ITEM CONDITION CHART Monitor item Condition Status LIFT FR SW-UP Lifting switch front (up) Operate ON Release OFF LIFT FR SW-DN Lifting switch front (down) Operate ON Release OFF Is the indication normal? YES: INSPECTION END NO: Perform diagnosis procedure. Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S42511855592010022700000) ".
  1. CHECK FUNCTION Turn ignition switch ON. Select "LIFT RR SW-UP", "LIFT RR SW-DN" in the "Data monitor" mode using CONSULT-III. Check lifting switch (rear) signal under the following conditions. MONITOR ITEM CONDITION CHART Monitor item Condition Status LIFT RR SW-UP Lifting switch rear (up) Operate ON Release OFF LIFT RR SW-DN Lifting switch rear (down) Operate ON Release OFF Is the indication normal? YES: INSPECTION END NO: Perform diagnosis procedure. Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S03031750252010022700000) ".
  1. CHECK FUNCTION Select "FORWARD SW" in the "Data Monitor" mode using CONSULT-III. Check the forward switch signal under the following condition. TEST ITEM CONDITION CHART Test item Condition Status FORWARD SW Driver side seat back Folded up ON Folded down OFF Is the indication normal? YES: INSPECTION END NO: Perform diagnosis procedure. Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S00455883932010022700000) ".
  1. CHECK FUNCTION Select "SEAT BELT SW" in the "Data Monitor" mode using CONSULT-III. Check the seat belt buckle switch signal under the following condition. TEST ITEM CONDITION CHART Test item Condition Status SEAT BELT SW Driver side seat belt Fastened ON Released OFF Is the indication normal? YES: INSPECTION END NO: Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S07250518112010022700000) ".
  1. CHECK FUNCTION Select "FWD LIMIT SW" in the "Data Monitor" mode using CONSULT-III. Check the sliding limit switch signal under the following condition. TEST ITEM CONDITION CHART Test item Condition Status FWD LIMIT SW Seat sliding Front edge ON Other than above OFF Is the indication normal? YES: INSPECTION END NO: Go to " «DIAGNOSIS PROCEDURE»(ref-356812-S41843493352010022700000) ".
  1. CHECK FUNCTION Select "WALK-IN SW" in the "Data Monitor" mode using CONSULT-III. Check the power walk-in switch signal under the following condition. TEST ITEM CONDITION CHART Test item Condition Status WALK-IN SW Power walk-in switch Pressed ON Released OFF Is the indication normal? YES: INSPECTION END NO: Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S03379506212010022700000) ".
  1. CHECK FUNCTION Turn ignition switch ON. Select "TILT SW-UP", "TILT SW-DN" in the "Data monitor" mode using CONSULT-III. Check tilt switch signal under the following conditions. MONITOR ITEM CONDITION CHART Monitor item Condition Status TILT SW-UP Tilt switch (up) Operate ON Release OFF TILT SW-DN Tilt switch (down) Operate ON Release OFF Is the indication normal? YES: INSPECTION END NO: Perform diagnosis procedure. Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S25692371062010022700000) ".
  1. CHECK FUNCTION Turn ignition switch ON. Select "TELESCO SW-FR", "TELESCO SW-RR" in the "Data monitor" mode using CONSULT-III. Check telescopic switch signal under the following conditions. MONITOR ITEM CONDITION CHART Monitor item Condition Status TELESCO SW-FR Telescopic switch (forward) Operate ON Release OFF TELESCO SW-RR Telescopic switch (backward) Operate ON Release OFF Is the indication normal? YES: INSPECTION END NO: Perform diagnosis procedure. Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S15200846232010022700000) ".
  1. CHECK FUNCTION Turn ignition switch ON. Select "MEMORY SW 1", "MEMORY SW 2" "SET SW" in the "Data monitor" mode using CONSULT-III. Check seat memory switch signal under the following conditions. MONITOR ITEM CONDITION CHART Monitor item Condition Status SET SW SET SW Push ON Release OFF MEMORY SW 1 Memory switch 1 Push ON Release OFF MEMORY SW 2 Memory switch 2 Push ON Release OFF Is the indication normal? YES: INSPECTION END NO: Perform diagnosis procedure. Refer to " «DIAGNOSIS PROCEDURE»(ref-356812-S37586468122010022700000) ".