Repair manual
Wiring diagrams
Infiniti FX35 I Repair Manual
Step-by-step repair and maintenance instructions for the Infiniti FX35 I (2002–2006): removal, installation, adjustment, diagnostics and parameter checks with illustrations.
86sections
890articles
ENManual language
- PRECAUTIONS FOR SUPPLEMENTAL RESTRAINT SYSTEM (SRS) "AIR BAG" AND "SEAT BELT PRE-TENSIONER"
- PRECAUTIONS FOR WORKING WITH HFC-134A (R-134A)
- Contaminated Refrigerant
- GENERAL REFRIGERANT PRECAUTIONS
- LUBRICANT PRECAUTIONS
- PRECAUTIONS FOR REFRIGERANT CONNECTION
- Features Of New Type Refrigerant Connection
- PRECAUTIONS FOR SERVICING COMPRESSOR
- Recovery/Recycling Equipment
- Electronic Leak Detector
- Vacuum Pump
- Manifold Gauge Set
- Service Hoses
- Service Couplers
- Refrigerant Weight Scale
- Charging Cylinder
- PRECAUTIONS FOR LEAK DETECTION DYE
- SPECIAL SERVICE TOOLS
- HFC-134A (R-134A) SERVICE TOOLS AND EQUIPMENT
- Refrigerant Flow
- Freeze Protection
- Refrigerant Pressure Sensor
- Pressure Relief Valve
- General
- Lubricant
- SYSTEM CONSTRUCTION
- Transmission Data And Transmission Order
- Air Mix Door Control (Automatic Temperature Control)
- Fan Speed Control
- Intake Door Control
- Outlet Door Control
- Self-Diagnostic System
- Display Screen
- Auto Switch
- Temperature Switch (Potentiometer Temperature Control) (Driver Side)
- Temperature Switch (Potentiometer Temperature Control) (Passenger Side)
- Recirculation (Rec) Switch
- Fresh (Fre) Switch
- Defroster (Def) Switch
- Rear Window Defogger Switch
- Off Switch
- A/C Switch
- Mode Switch
- Fan Switch
- Dual Switch (With Left And Right Ventilation Temperature Separately Control System)
- FAIL-SAFE FUNCTION
- CONSULT-II
- AUTO AMP. TERMINALS AND REFERENCE VALUE
- Auxiliary Mechanism: Temperature Setting Trimmer
- Auxiliary Mechanism: Foot Position Setting Trimmer
- Auxiliary Mechanism: Inlet Port Memory Function
- Checking Memory Function
- Checking Blower
- Checking Recirculation
- Checking Temperature Decrease
- Checking Temperature Increase
- Check A/C Switch
- Checking Auto Mode
- POWER SUPPLY AND GROUND CIRCUIT FOR AUTO AMP.
- Unified Meter And A/C Amp. (Automatic Amplifier)
- Potentio Temperature Control (PTC)
- LAN SYSTEM CIRCUIT
- MODE DOOR MOTOR CIRCUIT
- Component Parts
- Mode Door Motor
- AIR MIX DOOR MOTOR CIRCUIT
- Air Mix Door Motor
- AIR MIX DOOR MOTOR PBR CIRCUIT
- INTAKE DOOR MOTOR CIRCUIT
- Intake Door Motor
- BLOWER MOTOR CIRCUIT
- Automatic Mode
- Starting Fan Speed Control
- Blower Speed Compensation
- Brush-less Motor
- Blower Motor
- MAGNET CLUTCH CIRCUIT
- Low Temperature Protection Control
- INSUFFICIENT COOLING
- INSUFFICIENT HEATING
- MEMORY FUNCTION
- Ambient Sensor
- Ambient Temperature Input Process
- In-Vehicle Sensor
- Aspirator
- Sunload Sensor
- Sunload Input Process
- Intake Sensor
- Function
- Driver Side
- Passenger Side
- Discharging Refrigerant
- COMPONENTS
- Coil
- CHECKING FOR REFRIGERANT LEAKS
- CHECKING SYSTEM FOR LEAKS USING THE FLUORESCENT LEAK DETECTOR
- DYE INJECTION
- Precautions For Handling Leak Detector
- Checking Procedure
- ENGINE IDLING SPEED
- BELT TENSION
- WIRING DIAGRAMS AND TROUBLE DIAGNOSIS
- Diagnostic Procedure For A/C System
- Diagnostic Procedure For Mode Door Motor
- Diagnostic Procedure For Air Mix Door
- Diagnostic Procedure For Air Mix Door PBR
- Diagnostic Procedure For Intake Door Motor
- Diagnostic Procedure For Blower Motor
- Diagnostic Procedure For Magnet Clutch
- Test Conditions
- Test Reading
- Trouble Diagnosis For Unusual Pressure
- Diagnostic Procedure For Insufficient Cooling
- SELF-DIAGNOSIS
- Diagnostic Procedure For Ambient Sensor
- Diagnostic Procedure For In-Vehicle Sensor
- In-Vehicle Sensor
- Diagnostic Procedure For Sunload Sensor
- Diagnostic Procedure For Intake Sensor
- Inspection
- Lubricant Adjusting Procedure For Components Replacement Except Compressor
- Lubricant Adjusting Procedure For Compressor Replacement
- Removal
- Installation
- Replacement Timing
- Replacement Procedures
- Removal Of Center Ventilator Grille
- Removal Of Side Ventilation
- Removal Of Rear Ventilator Grille
- Removal of Foot Ducts
- ALPHABETICAL INDEX
- SUPPLEMENTAL RESTRAINT SYSTEM (SRS) "AIR BAG" AND "SEAT BELT PRE-TENSIONER"
- PRECAUTIONS
- ATF Cooler Service
- SPECIAL SERVICE TOOLS
- SHIFT MECHANISM
- N Position
- TCM FUNCTION
- Control System Outline
- Normal Control
- Back-Up Control (Engine Brake)
- During Shift Change
- SHIFT CONTROL
- Shift Change
- LOCK-UP CONTROL
- Lock-Up Released
- Lock-Up Applied
- Smooth Lock-Up Control
- Half-Clutched State
- Slip Lock-Up Control
- OBD-II FUNCTION FOR A/T SYSTEM
- One Trip Detection Logic
- Two Trip Detection Logic
- Freeze Frame Data and 1st Trip Freeze Frame Data
- FAIL-SAFE
- Vehicle Speed Sensor
- Accelerator Pedal Position Sensor
- Throttle Position Sensor
- PNP Switch
- Starter Relay
- A/T Interlock
- A/T 1st Engine Braking
- Line Pressure Solenoid
- Low Coast Brake Solenoid
- Input Clutch Solenoid
- Direct Clutch Solenoid
- Front Brake Clutch Solenoid
- High And Low Reverse Clutch Solenoid
- Turbine Revolution Sensor 1 Or 2
- Work Flow
- Information From Customer
- CHECK BEFORE ENGINE IS STARTED
- CHECK AT IDLE
- CONSULT-II
- CONSULT-II Setting Procedure
- Data Monitor Mode
- Possible Cause
- With CONSULT-II
- With GST
- Check PNP SW Circuit
- Check TCM
- Detect Malfunction Item
- Detect Malfunctioning Item
- Check CAN Communication Line
- Judgement of A/T Interlock
- Manual Mode Switch
- DTC NO. INDEX
- ON BOARD DIAGNOSTIC (OBD) SYSTEM OF A/T AND ENGINE
- How To Read DTC And 1st Trip DTC
- How To Erase DTC
- How To Erase DTC (With CONSULT-II)
- How To Erase DTC (With GST)
- How To Erase DTC (No Tools)
- DTC INSPECTION PRIORITY CHART
- Stall Test
- Road Test
- CRUISE TEST - PART 1
- CRUISE TEST - PART 2
- CRUISE TEST - PART 3
- SYMPTOM CHART
- TCM Inspection Table
- OBD-II Self-Diagnostic Procedure (With GST)
- OBD-II Self-Diagnostic Procedure (No Tools)
- Diagnostic Procedure
- DTC TEST PROCEDURES
- DTC Confirmation Procedure
- Check DTC
- Symptom
- PRECAUTIONS NECESSARY FOR STEERING WHEEL ROTATION AFTER BATTERY DISCONNECT
- PRECAUTIONS FOR DISCONNECTING FUEL PIPING
- SPECIAL SERVICE TOOLS
- CHECKING DRIVE BELTS
- Air Conditioner Compressor Belt
- Intake Manifold Collector (Lower)
- Water Hose
- Air Fuel Ratio Sensor and Heated Oxygen Sensor
- Check on Fuel Leakage
- Timing Chain
- Outer Diameter of Camshaft Journal
- Calculation of Camshaft Journal Oil Clearance
- Valve Lifter
- Outer Diameter of Valve Lifter
- Valve Lifter Hole Diameter
- Calculation of Valve Lifter Clearance
- Cylinder Head Distortion
- Valve Stem Diameter
- Valve Guide Inner Diameter
- Valve Guide Clearance
- Outline
- Preparation
- Vehicle Underbody
- When New Cylinder Block is Used
- When New Connecting Rod and Crankshaft are Used
- Undersize Bearings Usage Guide
- When Cylinder Block and Crankshaft are Reused
- Piston Pin Hole Diameter
- Piston to Piston Pin Oil Clearance
- Connecting Rod Bearing Housing Diameter (Big End)
- Piston Pin Bushing Inner Diameter (Small End)
- Connecting Rod Bushing Oil Clearance (Small End)
- Factory Installed Parts Grading
- Piston Skirt Diameter
- Piston-to-Cylinder Bore Clearance
- Re-boring Cylinder Bore
- Crankshaft Main Journal Diameter
- Main Bearing Cap Bolt Outer Diameter
- Oil Jet
- STANDARD AND LIMIT
- Engine Performance Diagnostic Routine Outline - General Information
- Engine Performance Safety Precautions
- Parasitic Load Explanation & Test Procedures - General Information 2
- Waveforms - Injector Pattern Tutorial - General Information 2
- Electrostatic Discharge Warning - General Information
- State Emission Standards - Diesel
- Diagnostic Trouble Code Definitions - General Information
- Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
- Precautions for NVIS/IVIS (NISSAN/INFINITI VEHICLE IMMOBILIZER SYSTEM - NATS) (If Equipped)
- Precautions Necessary for Steering Wheel Rotation After Battery Disconnect
- General Precautions
- Precautions for Three Way Catalyst
- Precautions for Fuel (Unleaded Premium Gasoline Recommended)
- Precautions for Fuel (Unleaded Premium Gasoline Required)
- Precautions for Multiport Fuel Injection System or Engine Control System
- Precautions for Engine Oils
- Health Protection Precautions
- Environmental Protection Precautions
- Precautions for Air Conditioning
- Terms
- Units
- Connector Symbols
- Component Indication
- Switch Positions
- Detectable Lines & Non-Detectable Lines
- Multiple Switch
- Reference Area
- Connector And Terminal Pin Kit
- How To Probe Connectors
- Male Terminal
- How to Check Enlarged Contact Spring of Terminal
- Sensors & Relays
- Engine Compartment
- Behind The Instrument Panel
- Under Seating Areas
- Heat Sensitive
- Freezing
- Water Intrusion
- Electrical Load
- Cold or Hot Start Up
- Continuity Check Method
- Voltage Check Method
- Resistance Check Method
- Voltage Drop Tests
- Measuring Voltage Drop (Accumulated Method)
- Measuring Voltage Drop (Step-By-Step Method)
- Checking Equipment
- Special Service Tools
- Garage Jack and Safety Stand
- 2-pole Lift
- Board-on Lift
- Tow Truck Towing
- AWD Models
- Recommended Chemical Products and Sealants
- SAE J1930 Terminology List
- Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
- OUTLINE
- COMBINATION SWITCH READING FUNCTION
- EXTERIOR LAMP BATTERY SAVER CONTROL
- VEHICLE SECURITY SYSTEM
- XENON HEADLAMP
- CAN Communication Unit
- Display Item List
- CONSULT-II Functions (IPDM E/R)
- High Beam Indicator Lamp Does Not Illuminate
- For details, refer to the regulations in your own country
- DELAY TIMER FUNCTION
- Major Components and Functions
- SETTING CHANGE FUNCTIONS
- Outline
- CAN COMMUNICATION UNIT
- WORK FLOW
- CONSULT-II FUNCTION
- 1. Check Fuse And Fusible Link
- 3. Check Ground Circuit
- 1. Check Door Switch Input Signal
- 2. Check Door Switch Circuit
- 3. Check Door Switch
- 1. Check Back Door Switch Input Signal
- 3. Check Back Door Switch
- 1. Check Key Switch Input Signal
- 2. Check Key Switch (With Intelligent Key)
- 3. Check Key Switch (Without Intelligent Key)
- 1. Check Door Lock And Unlock Switch Input Signal
- 2. Check Output Signal
- 2. Check Door Lock Actuator Signal
- 1. Check Front Door Key Cylinder Switch Input Signal (Lock Signal)
- 2. Check Front Door Key Cylinder Switch
- 1. Check Front Door Key Cylinder Switch Input Signal (Unlock Signal)
- CONSULT-II Inspection Procedure
- ACTIVE TEST
- Trouble Diagnosis Symptom Chart - With Front Power Window Anti-pinch System
- Trouble Diagnosis Symptom Chart - With Front and Rear Power Window Anti-pinch System — Part 1
- Trouble Diagnosis Symptom Chart - With Front and Rear Power Window Anti-pinch System — Part 2
- PRECAUTIONS FOR SUPPLEMENTAL RESTRAINT SYSTEM (SRS) "AIR BAG" AND "SEAT BELT PRE-TENSIONER"
- PRECAUTIONS
- SERVICE NOTICE
- SPECIAL SERVICE TOOLS
- AWD Warning Lamp
- FAIL-SAFE FUNCTION
- Basic Concept
- CONSULT-II Setting Procedure
- AWD Control Unit Part Number
- CONSULT-II Reference Value In Data Monitor Mode
- WHILE DRIVING, AWD WARNING LAMP FLASHES RAPIDLY (WHEN FLASHING IN APPROX. 1 MINUTE AND THEN TURNING OFF)
- WHILE DRIVING, AWD WARNING LAMP FLASHES SLOWLY (WHEN CONTINUING TO FLASH UNTIL TURNING IGNITION SWITCH OFF)
- Cases
- Bearing
- Shaft
- Gears And Chain