Crankcase Oil Capacity
During oil change 3.25 qts. (3.7L) is required to fill crankcase (including oil filter).
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) |
|---|
| A/C Tensioner Pulley Bracket Bolt | 17-20 (23-27) |
| Auto Tensioner Bolt | 15-20 (20-27) |
| Camshaft Bearing Cap Bolt (1) | 14-15 (19-20) |
| Camshaft Sprocket Bolt | 59-74 (80-100) |
| Connecting Rod Nut | 37-39 (50-53) |
| Crankshaft Pulley Bolt | 15-22 (20-30) |
| Crankshaft Sprocket Bolt | 81-96 (110-130) |
| Cylinder Head Bolt (2) | 65-74 (90-100) |
| Engine Support Bracket Bolt |
| Front | 37-48 (50-65) |
| Left | 22-31 (30-42) |
| Exhaust Manifold Nut | 18-22 (25-30) |
| Exhaust Pipe-To-Manifold Nut | 22-30 (30-40) |
| Flywheel/Drive Plate Bolt | 96-103 (130-140) |
| Front Cover Bolt | 11-13 (15-18) |
| Front Tensioner Pulley Bolt | 32-41 (43-55) |
| Idler Pulley Bolt | 25-31 (34-42) |
| Intake Manifold Bolt/Nut |
| 8-mm | 11-15 (15-20) |
| 10-mm | 22-31 (30-42) |
| Intake Manifold Bracket Bolt | 18-22 (25-30) |
| Main Bearing Cap Bolt | 48-52 (65-70) |
| Oil Filter Bracket Bolt | 11-16 (15-22) |
| Oil Pan Drain Plug | 26-61 (35-45) |
| Oil Pump Cover Bolt | 11-13 (15-18) |
| Oil Pump Driven Gear Bolt | 25-30 (34-40) |
| Oil Pump Pick-Up Tube Bolt | 11-16 (15-22) |
| Oil Pump Sprocket Nut | 37-44 (50-60) |
| Oxygen Sensor | 30-37 (40-50) |
| Plug Cap | 15-20 (20-27) |
| Rear Tensioner Retaining Bolt | 11-16 (15-22) |
| Rocker Arm Assembly Bolts | 14-15 (19-20) |
| Silent Shaft Sprocket Bolt | 32-36 (43-49) |
| Throttle Body Bolt | 11-16 (15-22) |
| Water Pump Mounting Bolt |
| Except 8 x 65 mm | 11 (15) |
| 8 x 65 mm | 15-20 (20-27) |
| Inch Lbs. (N.m) |
| Crankshaft Position Sensor Nut | 89-106 (10-12) |
| Distributor Nut | 89-106 (10-12) |
| Fuel Rail Bolt | 89-106 (10-12) |
| Oil Pan Bolt | 53-71 (6-8) |
| Oil Pressure Switch | 71-106 (8-12) |
| Rear Crankshaft Oil Seal Case Bolt | 89-106 (10-12) |
| Timing Belt Cover Bolt | 89-106 (10-12) |
| Valve Body Bolt | 89-106 (10-12) |
| Valve Cover Bolt | 22-31 (2.5-3.5) |
| Water Pump Pulley Bolt | 71-89 (8-10) |
| (1) Tighten bolts in sequence. (Схема №11) (2) Tighten bolts in sequence with engine cold. (Схема №1) |
| (1) | Tighten bolts in sequence. (Схема №11) |
| (2) | Tighten bolts in sequence with engine cold. (Схема №1) |
ENGINE SPECIFICATIONS
| Application | Specification |
|---|
| Displacement | 122 Cu. In. (2.0L) |
| Bore | 3.35" (85.0 mm) |
| Stroke | 3.46" (88.0 mm) |
| Compression Ratio | 9.0:1 |
| Fuel System | MFI |
| Horsepower @ RPM | 137 @ 6000 |
| Torque Ft. Lbs. @ RPM | 129 @ 5000 |
BALANCE SHAFT SPECIFICATIONS
| Application | In. (mm) |
|---|
| Left Balance Shaft |
| Journal O.D. |
| Front | .7270-.7276 (18.467-18.480) |
| Rear | 1.6126-1.6132 (40.959-40.975) |
| Oil Clearance |
| Front Journal | .0008-.0021 (.020-.054) |
| Rear Journal | .0017-.0033 (.042-.083) |
| Right balance Shaft |
| Journal O.D. |
| Front | 1.6519-1.6526 (41.959-41.975) |
| Rear | 1.6122-1.6129 (40.951-40.967) |
| Oil Clearance |
| Front Journal | .0008-.0024 (.020-.061) |
| Rear Journal | .0020-.0036 (.050-.091) |
BALANCE SHAFT SPECIFICATIONS
