Home ReviewsRefund Car not listed?
Home/Hyundai/Santa Fe/Hyundai Santa Fe I (2000-2012)/Repair manual/Heating, Ventilation & Air Conditioning/INSPECTION
Contents Section: Heating, Ventilation & Air Conditioning All sections

INSPECTION Hyundai Santa Fe I

Heating, Ventilation & Air Conditioning 17 illustrations ~425 words

INSPECTION

Apply the battery voltage as shown and check the blower motor rotation.

Scheme 66

Scheme 66: INSPECTION
Scheme 66: INSPECTION

Scheme 67

Scheme 67: INSPECTION
Scheme 67: INSPECTION
  1. Manually operate the control switch and measure the voltage of blower motor between pin 1 and 2.
  2. Select the control switch to raise voltage until high relay operates POWER TRANSISTOR SPECIFICATIONS Fan Motor Voltage First speed 3.8V +/- 0.5V Second speed 5.2V +/- 0.5V Third speed 6.5V +/- 0.5V Fourth speed 7.9V +/- 0.5V Fifth speed 9.5V +/- 0.5V Sixth speed 10.6V +/- 0.5V Seventh speed 12.0V (high relay operates)

Scheme 68

Scheme 68: REPLACEMENT
Scheme 68: REPLACEMENT

Scheme 69

Scheme 69
Scheme 69

Scheme 70

Scheme 70
Scheme 70

Scheme 71

Scheme 71
Scheme 71

Scheme 72

Scheme 72
Scheme 72
  1. Remove the negative (-) battery terminal
  2. After opening the glove box, pull it downward by pressing the both side of glove box inward
  3. Remove the lower side cover of the crash pad.
  4. Remove the upper cover of the glove box.
  5. Loosen the bolts of glove box.
  6. Disconnect the power transistor connector (A).
  7. Loosen the power transistor fixing screw and remove the power transistor CAUTION: Use the short length positive (+) screwdriver to remove the screw.
  8. Replace the power transistor with a new one.
  9. Reinstallation is the reverse order of the removal.

Scheme 73

Scheme 73: INSPECTION
Scheme 73: INSPECTION

Scheme 74

Scheme 74
Scheme 74
  1. Measure terminal-to-terminal resistance of the blower resistor.
  2. If measured resistance is not within specification, the blower resistor must be replaced. (After removing the resistor).

Scheme 75

Scheme 75: REPLACEMENT
Scheme 75: REPLACEMENT

Scheme 76

Scheme 76
Scheme 76

Scheme 77

Scheme 77
Scheme 77

Scheme 78

Scheme 78
Scheme 78

Scheme 79

Scheme 79
Scheme 79
  1. Remove the negative (-) battery.
  2. After opening the glove box, pull it downward by pressing the both side of glove box inward.
  3. Remove the lower side cover of the crash pad.
  4. Remove the upper cover of the glove box.
  5. Loosen the bolts of glove box.
  6. Disconnect the blower heater resistor connector (A).
  7. Loosen the resistor fixing screw and remove the resistor. CAUTION: Use the short length positive (+) screwdriver to remove the screw.
  8. Replace the resistor with a new one.
  9. Reinstallation is the reverse order of the removal.

Scheme 80

Scheme 80: REPLACEMENT
Scheme 80: REPLACEMENT

Scheme 81

Scheme 81
Scheme 81

Scheme 82

Scheme 82
Scheme 82
  1. After opening the glove box, pull it downward by pressing both sides of the glove box inward.
  2. After turning the knob of the filter cover counter clockwise, remove the filter cover.
  3. Remove the air conditioner upper filter by pulling it horizontally in ward as shown.
  4. Remove the lower filter by pulling it horizontally inward after lifting.
  5. Reinstall all removed components in reverse order of the removal

Note. When you replace the filters, be sure to align the grooves with lugs in the upper and lower filters for correct installation. Be sure to pull and push the filters horizontally to remove and install the filters