Home ReviewsRefund Car not listed?
Home/Hyundai/Genesis/Hyundai Genesis I рестайлинг (2011-2016)/Repair manual/Warning System/Front Back Warning System Diagnosis: Other
Contents Section: Warning System All sections

Front Back Warning System Diagnosis: Other Hyundai Genesis I рестайлинг

Warning System 10 illustrations ~646 words

Verification of Vehicle Repair

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 81

Scheme 81: Component Location
Scheme 81: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 82

Scheme 82: Component Location
Scheme 82: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 83

Scheme 83: Component Location
Scheme 83: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 84

Scheme 84: Component Location
Scheme 84: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 85

Scheme 85: Component Location
Scheme 85: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 86

Scheme 86: Component Location
Scheme 86: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 87

Scheme 87: Component Location
Scheme 87: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 88

Scheme 88: Component Location
Scheme 88: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 89

Scheme 89: Component Location
Scheme 89: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

Scheme 90

Scheme 90: Component Location
Scheme 90: Component Location

After a repair, it is essential to verify that the fault has been corrected.

  1. Connect scan tool and select "DTC Analysis" mode.
  2. Clear the DTCs and Operate the vehicle within DTC Enable conditions in General information.
  3. Is any DTC outputted again? YES Go to the applicable troubleshooting procedure. NO System performing to specification at this time.

More articles — Front Back Warning System Diagnosis