Programming and Setup: Removal & Installation Hummer H2 I рестайлинг

Air Suspension Control Module Replacement

If the electronic suspension control module is replaced, the following setup procedure must be performed

Refer to Suspension Position Calibration .

Air Spring Leveling Sensor Replacement

If an air spring leveling sensor is replaced, the following setup procedure must be performed

Refer to Suspension Position Calibration .

Compressor Assembly Automatic Level Control Replacement

If the compressor assembly automatic level control is replaced, the following setup procedure must be performed

Refer to Suspension Position Calibration .

ECM Replacement

If the engine control module (ECM) is replaced, the following procedures must be performed

1. ECM Reprogramming-Refer to «Service Programming System (SPS)»(ref-299148-S39074817972008092200000) .
2. The CKP System Variation Learn-Refer to «Crankshaft Position System Variation Learn»(ref-299142-S30680208552008092200000) .
3. Engine Oil Life Remaining-When available, use a scan tool to reset the Engine Oil Life Remaining back to the original percentage recorded before the module was replaced.
4. Transmission Fluid Life Remaining-When available, use the scan tool to reset the Transmission Fluid Life Remaining back to the original percentage recorded before the module was replaced.
5. Theft Deterrent-Refer to «Immobilizer System Component Programming»(ref-299168-S33661783492008092200000) .

Setup for Component Replacement

The replacement of some components will require a setup procedure for complete repair.

If any of the following components are replaced, the CKP Variation Learn Procedure must be performed. Refer to Crankshaft Position System Variation Learn .

1. Engine replacement
2. Any engine repair that disturbs the CKP sensor or its relationship with the crankshaft reluctor wheel
3. CKP sensor

The garage door opener (GDO) programming and setup procedures must be performed after replacement. Refer to Garage Door Opener Programming - Universal .

Each of the following service procedures may require programming or setup procedures to be performed on the HVAC control module or HVAC actuators.

HVAC Control Module Replacement

If the HVAC control module is replaced, an automatic re-calibration of all the actuators will occur. No additional procedures are necessary.

Actuator Replacement

If an actuator is replaced, the following procedure must be performed

Re-Calibrating Actuators-Refer to Actuator Recalibration .

1. Key on, Engine off. Program the SDM, refer to «Service Programming System (SPS)»(ref-299148-S39074817972008092200000) .
2. Key OFF then ON again. If a DTC is set current after programming, follow the diagnostic procedure for that fault. If the programming event was successful, the SIR Malfunction indicator should begin flashing with no current DTCs present.
3. Use the scan tool to perform the "Setup SDM Primary Key in BCM" Special Function in Module Setup.
4. Use the scan tool to perform the Setup New SDM special function. If during this procedure a fault is detected, the SDM will not allow this procedure to complete. Repair any existing DTC and then use the scan tool to command the special function again.
5. Key off then on again. Clear all codes and verify no current faults are present.

1. Key ON, Engine OFF. With the scan tool perform the Setup New ROS procedure for the inflatable restraint vehicle rollover sensor (ROS).
2. Key OFF then ON again. Clear all codes and verify no current faults are present.

Remote Control Door Lock Receiver Replacement - Copy and Paste TPM Information

This procedure will learn the TPM information to the new RCDLR using the Copy and Paste function on the scan tool. This procedure will extract the TPM Tire Type information as well as the sensor data from the existing RCDLR prior to its replacement and store this information in the scan tool. After RCDLR replacement and SPS programming, the tire type and sensor data stored in the scan tool is written to the new RCDLR, negating the need to perform the tire type setup and sensor learn procedure.

This procedure should be considered as the first programming choice when replacing an RCDLR. The Copy and Paste procedure eliminates the possibility of incorrectly inputting the tire type or learning stray TPM sensors.

1. Using a scan tool, navigate to the Copy and Paste TPM Information procedure and copy the existing TPM information from the RCDLR using the outline below. Follow the on-screen instructions after selecting Step 1: Vehicle Control Systems Module Setup Remote Control Door Lock Receiver Copy and Paste TPM Information Step 1
2. At this point, install the new RCDLR.
3. Program the RCDLR - Refer to «Service Programming System (SPS)»(ref-299148-S39074817972008092200000) .
4. Using a scan tool, navigate to the Copy and Paste TPM Information procedure to paste the stored TPM information using the outline below. Follow the on-screen instructions after selecting Step 2: Vehicle Control Systems Module Setup Remote Control Door Lock Receiver Copy and Paste TPM Information Step 2
5. Program the keyless entry transmitters - Refer to «Transmitter Programming»(ref-299151-S10370791362008092200000) .

Remote Control Door Lock Receiver Replacement - TPM Sensor Learn

This procedure will learn TPM information to the new RCDLR by manually inputting the tire type using the scan tool and performing the TPM sensor learn. This procedure should be performed if the above Copy and Paste procedure can not be completed. An example of this would be an RCDLR that is unable to communicate with the scan tool and is required to be replaced.

1. RCDLR Programming-Refer to «Service Programming System (SPS)»(ref-299148-S39074817972008092200000) .
2. Keyless Entry Transmitter Programming-Refer to «Transmitter Programming»(ref-299151-S10370791362008092200000) .
3. Tire Type Setup: Install a scan tool. Select Remote Control Door Lock Receiver under Module Setup in the Vehicle Control System menu. Select Tire Type/Pressure Selection. Follow the on-sceen instructions.
4. Tire Pressure Monitoring Sensor Learn-Refer to «Tire Pressure Sensor Learn»(ref-299169-S39353641412008092200000) .