Test Description
| WARNING | While engine is operating, the exhaust system will become extremely hot. To prevent burns avoid contacting a hot exhaust system. |
The numbers below refer to the step numbers in the diagnostic table.
- 3: The exhaust system has very low back pressure under normal conditions. If the exhaust system is restricted, a significant increase in the exhaust pressure is noticed on the J 35314-A Exhaust Back Pressure Gauge. See «Special Tools»(ref-364567-S30235984852010063000000) .Removing the heater oxygen sensor (HO2S) may set a diagnostic trouble code (DTC). When finishing this diagnostic table, be sure to clear all codes.
- 4: This step will isolate the catalytic converter from the remainder of the exhaust system.
- 7: Confirming that the condition has been fixed is essential. If the symptom still exists and the vehicle has a dual exhaust system, proceed to Step 2 and repeat the diagnostic procedure on the opposite exhaust pipe.
| Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
| 1 | Did you verify the customers complaint? | Go to Step 2 | ||
| 2 | Did you review the exhaust symptoms diagnostic information and perform the necessary inspections? | Go to Step 3 | Go to Symptoms - Engine Exhaust | |
| 3 | Remove the heated oxygen sensor (HO2S) that is in front of and closest to the catalytic converter. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) or Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) or Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) or Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) . Install the J 35314-A Exhaust Back Pressure Gauge in place of the HO2S sensor. See Special Tools . Start the engine. Increase and monitor the engine speed at 2,000 RPM. Observe the exhaust system back pressure reading on the gauge. Does the reading exceed the specified value? | 3.4 kPa (0.5 psi) | Go to Step 4 | Go to Step 7 |
| 4 | Turn the engine OFF and place the ignition in the lock position. Remove the J 35314-A . See Special Tools . Re-install the HO2S sensor. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) or Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) or Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) or Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) . Remove the post-catalyst HO2S sensor. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) or Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) or Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) or Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) . Install the J 35314-A in place of the post HO2S sensor. See Special Tools . Start the engine. Increase and monitor the engine speed at 2,000 RPM. Observe the exhaust system back pressure reading on the gauge. Does the reading exceed the specified value? | 3.4 kPa (0.5 psi) | Go to Step 5 | Go to Step 6 |
| 5 | Inspect the exhaust system for the following conditions: Damage in the exhaust pipe Debris in the exhaust pipe Muffler internal failure Two-layer exhaust pipe separation Did you find and correct the condition? | Go to Step 7 | ||
| 6 | Replace the catalytic converter. Refer to Catalytic Converter Replacement (with Exhaust Flange) or Catalytic Converter Replacement (with Exhaust Clamp) . Did you find and correct the condition? | Go to Step 7 | ||
| 7 | Remove the J 35314-A . See Special Tools . Re-install the HO2S sensor. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) or Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) or Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) or Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) . Clear any codes. Road test the vehicle in order to verify the repair. Did you correct the condition? | System OK | Go to Step 2 |
Exhaust System Description
| IMPORTANT | Use of non-OEM parts may cause driveability concerns. |
The exhaust system carries exhaust gases, treated by the catalytic converter, through the muffler and into a resonator, if applicable where exhaust noise is lessened.
In order to secure the exhaust muffler assembly to the exhaust manifold, a flange and seal-joint coupling is utilized. The exhaust system may utilize a slip-joint coupling design with a clamp and a U-bolt or a flange connection with a gasket.
Exhaust hangers and rubber insulators help to support the weight of the exhaust system along with insulating any exhaust system vibration, rattle, or noise.
Exhaust hangers also space the exhaust system away from the underbody of the vehicle and allows the exhaust system to expand as the exhaust system warms up.
Exhaust heat shields are used to protect the underbody and other components from damage due to the heat from the exhaust system.
The exhaust system may be comprised of the following components
- Catalytic converter
- Exhaust hanger
- Exhaust heat shield
- Exhaust insulator
- Exhaust manifold
- Exhaust muffler
- Exhaust pipe
- Exhaust resonator, if equipped
- Exhaust tail pipe, if equipped