| Astro & Safari |
| Ball Joint-To-Control Arm Nuts (5) | 22 (30) |
| Ball Joint-To-Steering Knuckle Nut (1) (5) |
| Lower | 92 (125) |
| Upper | 94 (128) |
| Drive Axle Shaft Nut | 173 (234) |
| Drive Axle Shaft-To-Differential Drive Flange Bolts | 60 (80) |
| Hub & Bearing-To-Steering Knuckle Bolts | 66 (90) |
| Lower Control Arm-To-Frame Pivot Bolt Nuts (2) (3) (5) | 135 (185) |
| Shock Absorber Nuts (4) | 66 (89) |
| Splash Shield Bolts | 12 (16) |
| Stabilizer Bar Clamp-To-Frame Bolts | 12 (16) |
| Stabilizer Bar Spacer Bolt | 22 (33) |
| Tie Rod End-To-Steering Knuckle Nut | 35 (47) |
| Torsion Bar Retainer-To-Support Nuts |
| Center Nut | 18 (24) |
| Edge Nuts | 46 (62) |
| Upper Control Arm-To-Frame Pivot Bolt Nuts (2) (5) | 88 (120) |
| "K" Series Blazer & Pickup, Sierra, Suburban & Yukon |
| Ball Joint-To-Control Arm Nuts (5) |
| Lower | 45 (60) |
| Upper |
| K15 & K25 Series Pickup and Sierra, Suburban & Yukon | 17 (23) |
| K35 Series Pickup & Sierra K35 | 52 (70) |
| Ball Joint-To-Steering Knuckle Nut (1) (5) |
| Lower | 94 (128) |
| Upper | 84 (115) |
| Drive Axle Shaft Nut | 173 (234) |
| Drive Axle Shaft-To-Differential Drive Flange Bolts | 60 (80) |
| Hub & Bearing-To-Steering Knuckle Bolts | 133 (180) |
| Lower Control Arm-To-Frame Pivot Bolt Nuts (2) (3) (5) | 135 (185) |
| Shock Absorber Nuts (4) | 66 (89) |
| Splash Shield Bolts | 19 (26) |
| Stabilizer Bar Clamp-To-Frame Bolts | 13 (18) |
| Stabilizer Bar Spacer Nut | 12 (16) |
| Tie Rod End-To-Steering Knuckle Nut | 35 (47) |
| Torsion Bar Retainer-To-Support Nuts |
| Center Nut | 18 (24) |
| Edge Nuts | 46 (62) |
| Upper Control Arm-To-Frame Pivot Bolt Nuts (2) (5) | 139 (188) |
| Bravada, Jimmy, Sonoma, Syclone, Typhoon & "T" Series Blazer & Pickup |
| Ball Joint-To-Control Arm Nuts (5) | 17 (23) |
| Ball Joint-To-Steering Knuckle Nut (1) (5) |
| Lower | 83 (112) |
| Upper | 61 (83) |
| Drive Axle Shaft Nut | 181 (245) |
| Hub & Bearing/Shield-To-Steering Knuckle Bolts | 86 (117) |
| Lower Control Arm-To-Frame Pivot Bolts (4) (5) | 148 (201) |
| Lower Control Arm-To-Frame Pivot Bolt Nuts (2) (4) (5) | 92 (125) |
| Shock Absorber Nuts (3) | 54 (73) |
| Stabilizer Bar Clamp-To-Frame Bolts | 35 (47) |
| Stabilizer Bar-To-Lower Control Arm Bolts | 24 (33) |
| Tie Rod End-To-Steering Knuckle Nut | 35 (47) |
| Torsion Bar Retainer-To-Support Bolts | 26 (35) |
| Torsion Bar Retainer-To-Support Nut | 25 (34) |
| Upper Control Arm-To-Frame Pivot Bolt Nuts (5) | 70 (95) |
| (1) Tighten nut to align cotter pin hole. DO NOT tighten nut more than an additional 1/6 turn to align cotter pin hole. (2) Use NEW nuts during reassembly. (3) Install both bolts with nuts facing rear of vehicle. (4) Install upper/rear bolt with nut facing rear of vehicle. Install lower/front bolt with nut facing front of vehicle. (5) Complete tightening of bolts and/or nuts with vehicle at proper riding height specification. |
