- Install pump gears into pump body with marked gear teeth indexed. If pick-up tube was removed, apply sealant to tube end. Tap tube end into pump using plastic hammer. Reassemble remaining components in reverse order of disassembly.
- Prime oil pump with engine oil. Install pump and extension shaft, ensuring slot on top of extension shaft engages with drive tang on end of distributor shaft. Tighten oil pump bolt to specification. See «TORQUE SPECIFICATIONS»(ref-49853-S42132455842001011600000) . Install oil pan.
Home/GMC/Jimmy Typhoon/GMC Jimmy Typhoon (1992-1993)/Repair manual/Mechanical/Reassembly & Installation
Contents
Section: Mechanical- Model Identification
- Engine Identification
- Valve Clearance Adjustment (VIN W)
- Valve Clearance Adjustment (VIN Z)
- Trouble Shooting
- Removal & Installation
- Fuel Pressure Release
- Engine
- Removal & Installation (astro & Safari)
- Removal & Installation (bravada)
- Removal & Installation ("c" & "k" Series)
- Removal & Installation (commercial Van)
- Removal & Installation ("g" Series)
- Removal & Installation ("s" Series)
- Removal & Installation ("t" Series, Except Syclone & Typhoon)
- Removal (VIN W)
- Removal (VIN Z, Except Syclone & Typhoon)
- Removal (syclone & Typhoon)
- Rocker Arm Studs (press-In Type)
- Oil Pan
- Removal (except "s" & "t" Series)
- Removal (bravada, Syclone & Typhoon)
- Removal ("s" Series)
- Removal ("t" Series, Except Bravada, Syclone & Typhoon)
- Installation (all Models)
- Valve Springs
- Valve Stem Oil Seals
- Valve Guides
- Valves
- Rocker Arm Assembly
- Piston & Rod Assembly
- Fitting Pistons
- Piston Rings
- Rod Bearings
- Crankshaft & Main Bearings
- Thrust Bearing
- Cylinder Block
- Engine Lubrication System
- Oil Pressure
- Oil Pump
- Removal & Disassembly
- Reassembly & Installation
- Engine Cooling
- Torque Specifications
- General Engine Specifications
- Crankshaft, Main & Connecting Rod Bearings Specifications
- Connecting Rods Specifications
- Pistons, Pins & Rings Specifications
- Cylinder Block Specifications
- Valves & Valve Springs (non-Turbo) Specifications
- Cylinder Head Specifications
- Camshaft Specifications
- Fluid Capacities Specifications
- Abbreviations
- Accessory Drive Belts
- Adjustments
- Anti-Lock/traction Control
- Application
- Automatic Trans
- Auxiliary Emission Control Systems
- Basic Trouble Shooting
- Brakes
- Charging System
- Check Lists
- Clutches Manual & Hydraulic
- Computer Relearn
- Cooling System (mechanical)
- Cruise Control Systems
- Diagnostic Connector Locations
- Differentials & Drive Axles
- Door Locks & Anti-Theft Systems
- Driveline/axles
- Driveshaft & Universal Joints
- Electrical
- Electrical Component Locations
- Electronic Suspension
- Emission Applications
- Engine
- Engine Performance
- Fuses & Circuit Breakers
- Gauges & Instrument Panels
- General Servicing - All Makes
- Heated Glass/defoggers
- Heater
- Identification
- Manual & Power Steering
- Manual HVAC System
- Manual Trans
- MAP Guidelines
- Mechanical
- Mechanical - Hydraulic
- Metric Conversions
- Mirrors
- Pin Voltage Charts
- Procedures
- Removal & Installation
- Reset Procedures
- Rpo Codes
- Sensor Range Charts
- Specifications
- Starter
- Steering
- Steering Column
- Steering Column Switches
- Steering Gear
- Suspension Front
- Suspension Rear
- Testing & Diagnostics
- Theory & Operation
- Traction Control Disable
- Transfer Case
- Transmission
- Wheel Alignment
- Windows
- Wiper/washer Systems
- Wiring Diagrams - Engine Performance