Maintenance Schedule: Other — Ford Taurus VI (2009-2012)

Engine Idle Hour Meter - Crown Victoria Police Interceptor, Taxi and Executive Series Town Car Equipped with Engine Idle Hour Meter

The vehicle may be equipped with an engine idle hour meter to indicate how much time the vehicle is idling in PARK or NEUTRAL. The engine idle hour meter is incorporated with the vehicle odometer. Depressing the odometer reset button once will display the trip odometer (miles followed by a T for trip odometer). Depressing the odometer reset button a second time will display the engine idle hour meter (hours followed by an H for hours). The engine idle hour meter will only accumulate time when the vehicle is in PARK or NEUTRAL. Displayed time is cumulative for the vehicle and the engine idle hour meter cannot be reset to zero . Emergency vehicles, such as police/fire and fleet vehicles, often experience long periods of idling, during which time the engine oil will continue to break down but mileage is not accumulated on the odometer.

To assist fleet managers in maintaining proper oil change intervals, the engine idle hour meter will help determine when an oil change is required. For every hour that the vehicle idles, it has accumulated the equivalent of approximately 53 km (33 mi) of driving. Using the combination of the vehicle odometer and the engine idle hour meter allows the fleet manager to better determine when the oil needs to be changed.

Engine idle hour meter calculation

Idle hours x 33 = miles equivalency
Miles driven + miles equivalency = oil change interval

Example: In metric units, this calculation would be 4,828 km + 3,233 (61 idle hours x 53 km/idle hour) = 8,061 km. When the odometer has accumulated 3,000 miles + 2,013 (61 hours x 33 miles/idle hour) = 5,013 miles, the oil change interval will have been reached.

Special Operating Condition Requirements

When towing a trailer or using a camper or car-top carrier

Change engine oil and install a new oil filter every 8,000 km (5,000 mi) or 6 months.
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise every 8,000 km (5,000 mi). Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Change automatic transmission fluid and filter (not required on 6R60/6R75/TorqShift® transmissions) every 48,000 km (30,000 mi).
Change transfer case fluid every 96,000 km (60,000 mi).
Change manual transmission fluid every 96,000 km (60,000 mi).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings as required.
Replace wheel bearing grease and install new grease seals on Rear Wheel Drive (RWD) front wheel bearings (if non-sealed bearings) every 48,000 km (30,000 mi).

Extensive idling and/or low speed driving for long distances, as in heavy commercial use such as delivery, taxi, patrol car or livery

Change engine oil and install a new oil filter every 8,000 km (5,000 mi), 6 months or every 200 hours of engine operation.
Install a new cabin air filter as required (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise every 8,000 km (5,000 mi). Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Inspect brake system every 8,000 km (5,000 mi).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings every 8,000 km (5,000 mi) or 6 months (if equipped).
Install a new fuel filter every 24,000 km (15,000 mi) on Crown Victoria, Grand Marquis, Town Car, Mustang, Ranger, F-Super Duty, Expedition EL and Navigator EL (not required for Fusion, Milan, MKZ, Edge, MKX, Taurus, E-Series, Expedition and Navigator with short wheelbase, F-150, Flex, MKS, Escape, Mariner, F-Series [non-Super Duty] and Transit Connect).
Change automatic transmission fluid and filter (not required on 6R60/6R75/TorqShift® transmissions) every 48,000 km (30,000 mi).
Replace wheel bearing grease and install new grease seals on RWD front wheel bearings (if non-sealed bearings) every 48,000 km (30,000 mi).
Install new spark plugs every 96,000 km (60,000 mi).
Change transfer case fluid every 96,000 km (60,000 mi).

When operating in dusty conditions such as unpaved or dusty roads

Change engine oil and install a new oil filter every 8,000 km (5,000 mi) or 6 months.
Install a new cabin air filter as required (if equipped).
Install a new engine air filter as required.
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise every 8,000 km (5,000 mi). Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings every 8,000 km (5,000 mi) or 6 months (if equipped).
Install a new fuel filter every 24,000 km (15,000 mi) on Crown Victoria, Grand Marquis, Town Car, Mustang, Ranger, F-Super Duty, Expedition EL and Navigator EL (not required for Fusion, Milan, MKZ, Edge, MKX, Taurus, E-Series, Expedition and Navigator with short wheelbase, F-150, Flex, MKS, Escape, Mariner, F-Series [non-Super Duty] and Transit Connect).
Change automatic transmission fluid and filter (not required on 6R60/6R75/TorqShift® transmissions) every 48,000 km (30,000 mi).
Replace wheel bearing grease and install new grease seals on RWD front wheel bearings (if non-sealed bearings) every 48,000 km (30,000 mi).
Change manual transmission fluid every 80,000 km (50,000 mi).
Change rear axle lubricant every 80,000 km (50,000 mi) (E-450 and F-450/550 only).
Change transfer case fluid every 96,000 km (60,000 mi).

When operating in off-road conditions

Change engine oil and install a new oil filter every 8,000 km (5,000 mi) or 6 months.
Install a new cabin air filter as required (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise every 8,000 km (5,000 mi) or 6 months. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings as required.
Change automatic transmission fluid and filter (not required on 6R60/6R75/TorqShift® transmissions) every 48,000 km (30,000 mi).
Replace wheel bearing grease and install new grease seals on RWD front wheel bearings (if non-sealed bearings) every 48,000 km (30,000 mi).
Change manual transmission fluid every 80,000 km (50,000 mi).
Change rear axle lubricant every 80,000 km (50,000 mi) (E-450 and F-450/550 only).
Change transfer case fluid every 96,000 km (60,000 mi).

Use of E85 fuel 50% of the time or greater (flex fuel vehicles only)

If run exclusively on E85, fill the fuel tank with a full tank of regular unleaded fuel every 4,800 km (3,000 mi).
Change engine oil and install a new oil filter every 8,000 km (5,000 mi) or 6 months.
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise every 8,000 km (5,000 mi). Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

When operating a Crown Victoria Police Interceptor, taxi or Town Car-Executive series equipped with an engine idle hour meter

Inspect brake system every 8,000 km (5,000 mi).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for play and noise every 8,000 km (5,000 mi). Vehicles with different front-to-rear tire pressure, the tire pressure must be adjusted and the tire pressure sensor trained.
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings every 8,000 km (5,000 mi) or 6 months (if equipped).
Change engine oil and replace filter every 8,000 km (5,000 mi), 6 months or as indicated by the time/mileage calculation.
Replace fuel filter every 24,000 km (15,000 mi).
Change automatic transmission fluid every 48,000 km (30,000 mi).
Install new spark plugs every 96,000 km (60,000 mi).
Inspect and replace cabin air filter as required (if equipped).

Checks and Services

Certain basic maintenance checks and inspections should be carried out at specified intervals. Any recognized adverse condition should be corrected as soon as possible.

In-Line, Service-Installed Transmission Fluid Filter (if equipped)

Some vehicles may be equipped with an in-line, service-installed transmission fluid filter. This filter is installed in the transmission fluid cooler return line. If equipped, install a new in-line filter during transmission fluid change intervals.

Maximum Oil Change Interval (Normal Schedule)

12,000 km (7,500 mi) or 6 months.

Maximum Oil Change Interval (Special Operating Conditions)

8,000 km (5,000 mi), 6 months or 200 hours of engine operation, whichever occurs first.

Engine Coolant Change Interval

6 years or 169,000 km (105,000 mi).
After initial change: 3 years or 73,000 km (45,000 mi).

Multi-Point Inspection

The following inspections are recommended at every service interval

Check and top off fluid levels for brakes, coolant, manual and automatic transmission (if equipped with an underhood fluid level indicator), power steering (if equipped) and window washer fluids.
Inspect tires for wear and correct air pressure, including spare tire.
Check exhaust system for leaks, damage, loose parts and foreign material.
Check battery performance.
Check operation of horn, exterior lamps, turn signals and hazard warning lights.
Check radiator, coolers, heater and A/C hoses.
Inspect windshield wiper spray and wiper operation.
Check windshield for cracks, chips and pitting.
Inspect for oil and fluid leaks.
Inspect halfshaft dust boots (if equipped).
Check shocks, struts and other suspension components for leaks and damage.
Inspect steering and linkage.
Inspect accessory drive belt(s).
Inspect clutch operation (if equipped).

Monthly Checks

Check each of the following items every month

All interior and exterior lights for correct operation.
Tires for wear and correct air pressure, including spare tire.
Engine oil fluid level.
Windshield washer solvent fluid level.

Six Month Checks

Check each of the following items at least every 6 months

Lap/shoulder belts and seat latches for wear and function.
External mounted spare tire is stowed correctly (tight to body).
Power steering fluid level (if equipped).
Washer spray, wiper operation and clean all wiper blades (install new wiper blades as necessary).
Parking brake for correct operation.
Lubricate all hinges, latches, door check straps and outside locks.
Lubricate upper and lower sliding door tracks (if equipped).
Clean sliding door contact switches (if equipped).
Lubricate door rubber weatherstrips.
Clean body and door drain holes.
Safety warning lamps (brake, ABS, air bag, safety belt) for correct operation.
Coolant system fluid level and correct strength.
Battery connections. Clean if necessary.
Clutch fluid level, if equipped.

Retighten Lug Nuts

The following check procedures should be carried out for all cars, minivans, light trucks, sport utilities, vans and Four-Wheel Drive (4WD) vehicles.

Retighten the wheel nuts to the specified torque at 800 km (500 mi) after any wheel disturbance (tire rotation, changing a flat tire or wheel removal).
On vehicles equipped with dual rear wheels, retighten the wheel nuts to the specified torque at 160 km (100 mi) and again at 800 km (500 mi) of new vehicle operation or after any wheel disturbance (tire rotation, changing a flat tire or wheel removal).

Normal Schedule

12,000 km (7,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

24,000 km (15,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Inspect automatic transmission fluid level (if equipped with an underhood fluid level indicator).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Inspect halfshaft boots (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Inspect brake pads, rotors, brake linings, drums, brake lines, hoses and parking brake system.
Inspect engine cooling system and hoses.
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

36,000 km (22,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Inspect cabin air filter (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

48,000 km (30,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Install a new engine air filter.
Install new climate controlled seat cushion filters (if equipped).
Install a new fuel filter on Crown Victoria, Grand Marquis, Town Car and Mustang (not required for Fusion, Milan, MKZ, Edge, MKX, Taurus, Focus, E-Series, Expedition and Navigator with short wheelbase, F-150, Flex, MKS, Escape, Mariner, F-Series [non-Super Duty] and Transit Connect).
Inspect automatic transmission fluid level (if equipped with an underhood fluid level indicator).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Inspect halfshaft boots (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Inspect brake pads, rotors, brake linings, drums, brake lines, hoses and parking brake system.
Inspect engine cooling system and hoses.
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

60,000 km (37,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Inspect cabin air filter (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

72,000 km (45,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Inspect automatic transmission fluid level (if equipped with an underhood fluid level indicator).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Inspect halfshaft boots (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Inspect brake pads, rotors, brake linings, drums, brake lines, hoses and parking brake system.
Inspect engine cooling system and hoses.
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

84,000 km (52,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Inspect cabin air filter (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

96,000 km (60,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Install a new engine air filter.
Install new climate controlled seat cushion filters (if equipped).
Install a new fuel filter on Crown Victoria, Grand Marquis, Town Car and Mustang (not required for Fusion, Milan, MKZ, Edge, MKX, Taurus, Focus, E-Series, Expedition and Navigator with short wheelbase, F-150, Flex, MKS, Escape, Mariner, F-Series [non-Super Duty] and Transit Connect).
Inspect automatic transmission fluid level (if equipped with an underhood fluid level indicator).
Change automatic transmission fluid and filter on all vehicles equipped with the TorqShift® transmission.
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Inspect halfshaft boots (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Replace wheel bearing grease and install new grease seals on RWD front wheel bearings (if non-sealed bearings).
Inspect brake pads, rotors, brake linings, drums, hoses and parking brake system.
Inspect engine cooling system and hoses.
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

108,000 km (67,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Inspect cabin air filter (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

120,000 km (75,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Inspect automatic transmission fluid level (if equipped with an underhood fluid level indicator).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Inspect halfshaft boots (if equipped).
Inspect brake pads, rotors, brake linings, drums, hoses and parking brake system.
Inspect engine cooling system and hoses.
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

132,000 km (82,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Inspect cabin air filter (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

144,000 km (90,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Install a new engine air filter.
Install new climate controlled seat cushion filters (if equipped).
Install a new fuel filter on Crown Victoria, Grand Marquis, Town Car and Mustang (not required for Fusion, Milan, MKZ, Edge, MKX, Taurus, Focus, E-Series, Expedition and Navigator with short wheelbase, F-150, Flex, MKS, Escape, Mariner, F-Series [non-Super Duty] and Transit Connect).
Install new spark plugs.
Inspect automatic transmission fluid level (if equipped with an underhood fluid level indicator).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Inspect halfshaft boots (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Inspect brake pads, rotors, brake linings, drums, brake lines, hoses and parking brake system.
Inspect engine cooling system and hoses.
Inspect accessory drive belt(s).
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

156,000 km (97,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Inspect cabin air filter (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

168,000 km (105,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Inspect automatic transmission fluid level (if equipped with an underhood fluid level indicator).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Inspect halfshaft boots (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Change rear axle fluid on vehicles equipped with DANA axles which use synthetic lubricants.
Inspect brake pads, rotors, brake linings, drums, brake lines, hoses and parking brake system.
Change engine coolant.
Inspect engine coolant system and hoses.
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

180,000 km (112,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Inspect cabin air filter (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

192,000 km (120,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Install a new engine air filter.
Install new climate controlled seat cushion filters (if equipped).
Install a new fuel filter on Crown Victoria, Grand Marquis, Town Car and Mustang (not required for Fusion, Milan, MKZ, Edge, MKX, Taurus, Focus, E-Series, Expedition and Navigator with short wheelbase, F-150, Flex, MKS, Escape, Mariner, F-Series [non-Super Duty] and Transit Connect).
Change automatic transmission fluid and filter on all vehicles equipped with the TorqShift® transmission.
Inspect automatic transmission fluid level (if equipped with an underhood fluid level indicator).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Replace wheel bearing grease and install new grease seals on RWD front wheel bearings (if non-sealed bearings).
Inspect halfshaft boots (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Inspect brake pads, rotors, brake linings, drums, brake lines, hoses and parking brake system.
Inspect engine cooling system and hoses.
Inspect accessory drive belts.
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

204,000 km (127,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Inspect cabin air filter (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

216,000 km (135,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Inspect automatic transmission fluid level (if equipped with an underhood fluid level indicator).
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Inspect halfshaft boots (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Inspect brake pads, rotors, brake linings, drums, brake lines, hoses and parking brake system.
Inspect engine cooling system and hoses.
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

228,000 km (142,500 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Inspect cabin air filter (if equipped).
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.

240,000 km (150,000 mi)

Change engine oil and install a new oil filter.
Perform «MULTI-POINT INSPECTION (RECOMMENDED)»(ref-355695-S05366984762010012800000) .
Rotate tires, inspect tires for wear, measure tread depth and inspect wheel ends for end play and noise. Vehicles with dual rear wheels should only be rotated if unusual wear is noted. For vehicles with different front-to-rear tire pressures, the tire pressure must be adjusted and the tire pressure sensor training must be done.
Install a new cabin air filter (if equipped).
Install a new engine air filter.
Install new climate controlled seat cushion filters (if equipped).
Install a new fuel filter on Crown Victoria, Grand Marquis, Town Car and Mustang (not required for Fusion, Milan, MKZ, Edge, MKX, Taurus, Focus, E-Series, Expedition and Navigator with short wheelbase, F-150, Flex, MKS, Escape, Mariner, F-Series [non-Super Duty] and Transit Connect).
Change automatic transmission fluid and filter (except for 6F35, 6F50, AWF-21, FNR5 and TorqShift® transmissions).
Change manual transmission fluid (if equipped).
Change transfer case fluid, 4WD (if equipped).
Change front differential fluid, 4WD (if equipped).
Replace rear axle lubricant on all RWD vehicles.
Inspect and lubricate control arms, steering linkage, steering ball joints, U-joints and driveshaft with zerk fittings (if equipped).
Inspect halfshaft boots (if equipped).
Inspect and lubricate 4WD front axle shaft U-joints (if equipped).
Install new front wheel bearings (if not sealed units).
Inspect brake pads, rotors, brake linings, drums, brake lines, hoses and parking brake system.
Change engine coolant.
Inspect engine cooling system and hoses.
Install a new accessory drive belt(s) (if a new belt(s) has not been installed within the last 160,000 km [100,000 mi]).
Inspect exhaust system and heat shields.
Check the rear spring U-bolt nuts for correct torque every 24,000 km (15,000 mi) (Transit Connect).

Maximum Oil Change Interval

Normal schedule: 12,000 km (7,500 mi) or 6 months, whichever occurs first.
Special operating conditions: 8,000 km (5,000 mi), 6 months or 200 hours of operation, whichever occurs first.

Motorcraft® Coolant

Change engine coolant at 6 years or 168,000 km (105,000 mi) of the vehicle's life, whichever occurs first.
After the initial change, change coolant every 3 years or 72,000 km (45,000 mi) thereafter.

Class A Motorhome

Every 2 years - change brake fluid.
Every 96,000 km (60,000 mi) change automatic transmission fluid.

Every 8,000 km (5,000 mi) change oil and filter.
Every 8,000 km (5,000 mi) rotate tires.

Mustang Shelby GT500

Every 8,000 km (5,000 mi) rotate tires.
Every 72,000 km (45,000 mi) replace spark plugs.

Maintenance Schedule: Other Ford Taurus VI