Crankcase Capacity
Crankcase capacity, including oil filter, is 6.7 qts. (6.35L).
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) |
|---|
| A/C Compressor Bolt | 17-27 (23-37) |
| Balance Shaft Sprocket Bolt | 34-42 (46-58) |
| Bellhousing-To-Engine Bolt | 25-33 (34-45) |
| Camshaft Bearing Cap Bolts (1) |
| Step 1 | (2) |
| Step 2 | 12-15 (16-20) |
| Camshaft Sprocket Bolt | 48-70 (65-95) |
| Connecting Rod Cap Nut |
| Step 1 | 30-33 (41-45) |
| Step 2 | Additional 90-120 Degrees |
| Crankshaft Damper Bolt |
| Step 1 | 77-99 (104-134) |
| Step 2 | Loosen bolt 360 Degrees |
| Step 3 | 35-39 (47-53) |
| Step 4 | Additional 85-95 Degrees |
| Cylinder Block Bearing Holder Bolt | 16-22 (22-30) |
| Cylinder Head Bolt (3) |
| Step 1 | 20-23 (27-31) |
| Step 2 | Additional 85-95 Degrees |
| Flexplate-To-Converter Bolt | 20-33 (27-44) |
| Flywheel Bolt | 55-61 (75-83) |
| Idler Pulley Bolt | 37-38 (50-52) |
| Lower Intake Manifold Bolt | 14-20 (18-27) |
| Lower Cylinder Block Bolt (4) |
| Bolts 1-10 | 17-20 (23-27) |
| Bolts 11-20 | 28-31 (38-42) |
| Bolts 1-20 | Additional 85-95 Degrees |
| Bolts 21-31 | 15-22 (20-30) |
| Power Steering Pump Bolt | 14-20 (18-27) |
| Power Steering Pulley Bolt | 41-50 (56-68) |
| Sub-frame to body bolt | 57-76 (77-103) |
| Timing Chain Cover-To-Block | 14-20 (18-27) |
| Upper Intake Manifold Bolt | 14-20 (18-27) |
| Water Pump Bolt | 14-20 (19-27) |
| INCH Lbs. (N.m) |
| Oil Pump Bolt | 80-115 (9-13) |
| (1) Tighten in sequence. (Схема №8)& 6. (2) Tighten bolts to 62-106 INCH lbs. (7-12 N.m) (3) Always use NEW cylinder head bolts. Tighten in sequence. (Схема №10) (4) Tighten in sequence. (Схема №11) |
| (1) | Tighten in sequence. (Схема №8)& 6. |
| (2) | Tighten bolts to 62-106 INCH lbs. (7-12 N.m) |
| (3) | Always use NEW cylinder head bolts. Tighten in sequence. (Схема №10) |
| (4) | Tighten in sequence. (Схема №11) |
GENERAL SPECIFICATIONS
| Application | Specification |
|---|
| Displacement | 207 Cu. In. (3.4L) |
| Bore | 3.25" (82.9 mm) |
| Stroke | 3.13" (79.5 mm) |
| Compression Ratio | 10:1 |
| Fuel System | SFI |
| Horsepower @ RPM | 235 @ 6100 |
| Torque Ft. Lbs. @ RPM | 230 @ 4800 |
OIL PUMP SPECIFICATIONS
| Application | In. (mm) |
|---|
| Rotor Tip Clearance | .0024-.0094 (.06-.24) |
| Rotor Housing Side Clearance | .0012-.0035 (.030-.090) |
| Rotor Shaft Clearance | .0012-.0037 (.030-.095) |
| Oil Pump Gear-To-Housing Clearance | .0039-.0069 (.100-.175) |
| Relief Valve-To-Bore Clearance | .0020-.0035 (.052-.088) |
